Sanji ZX400 User manual

SANJI SECURITY SYSTEMS (PTY) LTD
106 16TH ST MIDRAND
GAUTENG, SOUTH AFRICA
TEL [phone]
FAX [phone]
E Mail : [email protected]
http://www.sanji.co.za
29) USING YOUR PINCODE OVERRIDE (ZX400 & 500 ONLY)
The ZX400 and ZX500 can be temporarily overridden by
entering the supplied 5 digit pincode override by means of
turning the ignition switch on and off in a sequence as
per instructions below. If the unit is in immobiliser armed
mode (dash led solid) you can begin to enter your code. If
the alarm is set, open the door and turn the ignition on.
Wait for the unit to stop sounding, turn the ignition off.
You can begin to enter your code.
ZX300-400-500-USER-REV3
EXAMPLE
PINCODE
3 1 4 2 1
FITMENT CENTRE STAMP:
dash led
30) ANTI KEY THEFT KEYPAD
The optional anti key theft keypad protects the vehicle
against theft in the event of key theft or driver mugging.
A personal pin code has to be entered into the keypad
before the vehicle can be driven. The unit will come default
with code 1 1 1 1.
RESETTING THE IMMOBILISER :
Reset the alarm via your remote control (unlock button),
the alarm dash led will be flashing rapidly. Turn the
ignition on and enter your 4 digit code, the keypad led
will turn on for 5 seconds, the unit will reset the
immobiliser, the alarm dash led will turn off, the vehicle
can now be driven. You can also enter your code before
turning the ignition on however once you have entered
your code you then have 5 seconds to turn the ignition on
in order for the immobiliser to be reset so the vehicle can
be driven.
KEYPAD NUMBERS AND BUTTONS :
When you press any button the unit will beep and the
numbers will light up for 10 seconds. If a door is opened
the keypad numbers will light up.
INCORRECT CODE :
If an incorrect code is entered the unit will sound a rapid
beep to warn you that the wrong code was entered. You
have 4 attempts to enter your correct code, after the 4th
attempt the unit will lock up for 10 minutes. The unit will
beep and flash the numbers for a 10 minute period to
warn you that the keypad has locked up. During this time
you will be unable to reset your immobiliser.
CHANGING YOUR 4 DIGIT CODE :
Press button 1 and 5 simultaneously until the unit sounds
a long beep.
A) Enter your current 4 digit code, if the correct code is
entered the unit will sound a long beep and enter change
code mode. The keypad led will turn on solid. (If incorrect
code is entered the unit will exit change code mode and
revert back to normal operation).
B) Enter your new 4 digit code, after the 4th digit is
entered the unit will sound a long beep.
C) Enter your new 4 digit code again as confirmation. If
the 1st code matches the 2nd code, the new code will be
saved, if they don't match the new code will not be saved
and the current code will remain.
*
1 2 3 4 5
If you enter an incorrect digit the unit will not flash the
indicators and will revert back to the first digit. If you
enter an incorrect digit 3 times the unit will sound the
alarm. Turn the ignition on and wait for the unit to stop
sounding. You can now re-enter your code.
Digit 2 [number 1]
Turn ignition key on, led will start to flash, after the
FIRST flash, turn ignition key off, the indicators will flash
once, you have now successfully put your second digit in.
Digit 1 [number 3]
Turn ignition key on, led will start to flash, on the THIRD
flash, turn ignition key off, the indicators will flash once,
you have now successfully put your first digit in.
Digit 3 [number 4]
Turn ignition key on, led will start to flash, after the
FOURTH flash, turn ignition key off, the indicators will
flash once, you have now successfully put your third digit
in.
Digit 4 [number 2]
Turn ignition key on, led will start to flash, after the
SECOND flash, turn ignition key off, the indicators will
flash once, you have now successfully put your fourth
digit in.
Digit 5 [number 1]
Turn ignition key on, led will start to flash, after the
FIRST flash, turn ignition key off, the indicators will flash
once, you have now successfully put your fifth digit in
and have successful overridden your vehicle.
31) REMOTE LOW BATTERY WARNING
The remote led will normally be on solid when pressing
any button. If the remote batteries are low the led on your
remote control will flash. Replace the batteries with:
2 x CR1220 lithium batteries.

Briefed with the idea of “The Super intelligent Design Concept”
Sanji engineers developed the ZX Range of vehicle
security alarm and immobiliser systems. The ZX range
professional
represents the 'state of the art' in vehicle security. Read these
instructions for correct system operation. All points marked
are optional features. Refer to the back of the leaflet to find out
which product you have.
1) SETTING THE
ALARM To enable the
immobiliser
and full
alarm
features.
Press the lock button, the unit
will sound 2 soft chirps and the
indicators will flash twice. If
fitted with central locking the
doors will lock and the sensor
will switch on.
2) DOOR / BOOT /
BONNET OPEN
WARNING
To warn the
driver that a
door or boot
is open when
setting the
alarm.
The unit will sound two
additional loud chirps and flash
the indicators twice when
setting the alarm. If a door is
still open when the unit fully
arms, the doors will be
bypassed. The system will
assume a faulty door switch.
4) ALARM FAST
ARM To skip the 25
second delay
period.
After the alarm has been set
press the lock button again. The
unit will now go to fully armed
and the dash led will flash
slowly.
3) ALARM DELAY
PERIOD 25 second
arming delay. The dash led will flash rapidly
during the 25 second delay
period. After the delay, the dash
led will start to flash slowly. The
alarm and immobiliser is now
fully armed.
*
dash led
flashing
rapidly
dash led
flashing
slowly
dash led
flashing
rapidly
5) ALARM ARMED
CONFIRMATION To confirm
alarm armed
mode.
Press the lock button, the
indicators will flash once to
confirm that the alarm is fully
set.
15) REMOTE
PANIC To enable the
siren to
sound and the
indicators to
flash under
emergency
conditions.
Press either button continuously
for +/- 3 seconds. When in panic,
the unit can be driven. Press the
unlock button to reset panic.
16) HI-JACK
SERVICE
MODE
To temporarily
disable hi-jack. In drive, (ignition on, dash led
off), press the lock and unlock
buttons simultaneously, the siren
will chirp once. Hi-jack is now
disabled.
To reactivate
hi-jack repeat the above
procedure, the siren will chirp
twice.
When the ignition is
turned on to drive, the unit will
flash the indicators once to warn
the user that the unit is in hi-
jack service mode.
Dash led
off
*
12) DOOR LOCK
ON START Automatic
locking of all
doors when
ignition is
turned on.
When the ignition is turned on, if
all the doors, boot and bonnet
are closed, the doors will lock.
13) DOOR LOCK
/ UNLOCK
IN DRIVE
To lock or
unlock the
doors from
the remote
while the car
is running.
Press the unlock button to
unlock the doors. Press the lock
button to lock the doors.
*
14) DOOR
UNLOCK
ON IGNITION
OFF
To open the
doors when
the ignition is
turned off.
Switch the ignition off. All the
doors will unlock. If fitted with
selective unlock, only the driver’s
door will open. Press the unlock
button to open the passenger
doors.
*
UNLOCK
LOCK
6) SENSOR SHUT
DOWN
7) RESETTING
THE ALARM
9) AUTO ZONE
BYPASS
10) VIOLATION
CHIRPS
To reset the
immobiliser
and alarm.
Auto-
matically
bypass a
defective
zone.
To indicate to
user that the
alarm has
triggered
in his/her
absence.
Press the unlock button. The
unit will sound 1 soft chirp and
the indicators will flash once. If
fitted with central locking the
doors will unlock.
If the unit detects a permanently
faulty zone, e.g. door or sensor
during alarm set, the system will
sound 3 times then isolate
the faulty zone.
When the alarm is reset, the
unit will sound 4 loud chirps
if the alarm had triggered during
the alarm set mode.
11) STARTING
THE
VEHICLE
To start the
vehicle after
the alarm has
been reset.
When the alarm is reset the
dash led will be off, the vehicle
can be started within 60
seconds. After 60 seconds the
immobiliser will be armed, dash
led on. Press the unlock button
the dash led will turn off, the
vehicle can now be started.
8) SELECTIVE
UNLOCK ON
ALARM
RESET
To reset the
alarm and
open the
driver’s door
only.
Press the unlock button. The unit
will reset and selectively only
open the driver’s door. To open
the passenger doors press the
unlock button again.
*
dash led
off
IGNOR POINTS 11 & 12 FOR AN ALARM ONLY PRODUCT
To disable the
interior sensor
so that a pet
or person can
remain inside
the vehicle
when the
alarm is set.
Press both buttons together
when setting the alarm. The
siren will sound 4 loud chirps
and the indicators will flash
twice. The sensor has now
been disabled (green LED will
turn off). After 25 seconds the
system will be fully armed.
17) FORCED
HI-JACK
MODE
Forced hi-jack
in drive.
*
When you start the vehicle, the
unit will enter hi-jack, the dash
led will give a 1 second pulse.
Refer to point 21 to reset hi-jack.
If you start the vehicle with the
hidden button pressed, the unit
will not enter forced hi-jack.
18) DRIVER’S
DOOR
HI-JACK
To activate
hi-jack. In drive open then close driver’s
door. If all doors, bonnet and
boot are closed the dash led will
give a 1 second pulse. The unit
has entered hi-jack phase.
*
To reset the
unit back to
normal drive
mode.
21) RESETTING
HI-JACK
*
Press the hidden push button at
any time for +/- 2 seconds, the
unit will chirp once to confirm
that hi-jack has been reset.
19) HI-JACK
OPERATION Hi-jack mode. Countdown period is 90 sec. If
ignition is turned off during this
time, the timer will stop. When
the ignition is turned on again
the timer will continue. If you try
to set the alarm during the
countdown period, the unit will
sound 4 loud chirps to warn you
that you are in hi-jack mode.
*
20) HI-JACK
WARNING
PERIOD
Hi-jack
warning
mode.
After the countdown period the
unit will enter the 20second
warning period. The unit will
chirp and flash the indicators.
After this period the unit will
enter the 8 second slow down
period. At any point in time you
can reset hi-jack by pressing the
hidden button.
*
23) ONE EVENT
OVERRIDE To override
the
immobiliser
or alarm, in
the event of a
flat remote
battery.
In any mode, turn the Ignition on
and press the hidden push button
for +/- 2 seconds until the unit
chirps once, the system will be
reset. This is a once off
override.
24) PERMANENT
OVERRIDE To put the
unit into
permanent
override.
In drive mode, press and hold the
hidden button until the
unit chirps once. The unit is now
in permanent override. The dash
led will flash continuously. The
alarm and immobiliser features
will now be dormant.
Repeat this procedure to
exit service mode.
(+/-10sec)
If you try to
set the alarm you will hear 8
chirps.
ZX300 ONLY
26) BOOT
RELEASE
FUNCTION
To open the
boot.
*
Press the boot release button
(ignition off). The boot will open.
If the alarm was set the boot will
open and the alarm will be reset.
ZX500 ONLY
27) REMOVE
SET / RESET
CHIRPS
Set / reset
chirps OFF. You can deactivate the set/reset chirps so when you set or reset
the alarm there will be no chirps.
Just press the unlock and boot
release buttons together. The unit
will chirp once as confirmation.
28) ENABLE
SET / RESET
CHIRPS
Set / reset
chirps ON. You can activate the set/reset chirps so when you set or reset
the alarm there will be chirps.
Just press the lock and boot
release buttons together. The unit
will chirp twice as confirmation.
22) FINAL
HI-JACK To confirm
what phase
the unit is in.
*
In final hi-jack the siren will
sound on and off at 5 second
intervals and the indicators will
flash. The immobiliser will be
armed. The unit can be reset by
pushing the hidden button for
+/- 2 seconds. Push the hidden
button for +/- 6 sec for ZX500.
ZX300 & ZX400 ONLY
25) REMOVE
SET/RESET
CHIRPS
Set / reset
chirps OFF. In drive mode press the hidden
button and turn the ignition off
immediately. Continue to press
the button until the unit chirps
once. The set / reset chirps have
now been removed. To turn the
set / reset chirps back on repeat
the above procedure, the unit will
chirp twice.