Sanjin SE-6000 User manual

PROFESSIONAL DSP KARAOKE MIXER
CAUTION
DO NOT OPEN
USER’S MANUAL
USER’S MANUAL
SE-6000

FEATURES
BBE BOOST to control gain of bass for BBE effect with BBE ON/OFF
Build-in 24-bit high-speed DSP digital chip with 48KHz sampling rate
Build-in real-time feedback eliminator processor to filter out howling feedback noise from the speakers
automatically
Supports up to 16 internal effects including 8 fixed effects and 8 programable effects
DSP Echo & Vocal Reverb with Level control
DSP Vocal Echo with Level, Repeat and Delay controls
5 microphone channels(3 front+2 rear) with individual Master volume control and LF,MLF,MHF,HF filters
Assignable Music channel with volume, Balance, BBE BOOST control & LF,MF, HF filter
4-Band Equalizer for best fidelity and precision tuning for music control
6-Band Equalizer for best fidelity and precision tuning for microphone control
User Lock-Down mode to prevent most user from changing any setting
2 switchable stereo A/V channel input and 1 A/V output
Balance subwoofer output with Proportion Volume and Frequency controls
Balance center output with assignable Volume & Balance Controls
Balance rear output with Volume control
Balanced L/R XLR Master output & Unbalanced L/R RCA Master output
Supports external controller
Full functions LCD display for setup menu
19" rack mountable
*Feedback Eliminator- SE-6000's real-time feedback eliminator processor was designed to provide state-
of-the-art feedback elimination processing, while maintaining a simple control interface. You just select one
of the 3 room sizes and it will automatica lly filter out howling feedback noise from the speakers. This is a
necessary function for any venue that is looking for a professional sound environment or any KJ who are
looking to prolong your speakers' life.
*Digital Effect Processor- The SE-6000 has a powerful built-in Reverb and Echo Effects that can dramatically
increase the quality of your p erformance. A “reverb” is created when a sound is prod uced in an encl osed
space causing a large number of echoes to build up and the slowly decay. Reverb is most noticeable when
the sound source stops but the reflections continue, decreasing in amplitude, until they can no longer be
heard. T he SE -6 00 0 e na bles you to adjust the reverb tim e, re ve rb le ve l, ec ho re pe at and echo delay to
optimize your sound effects.
*13 -B and Musi c and 22- Ba nd Micro ph one Equali zer (EQ)- The S E-6000 h as two inde pendent 13 band
equalizers for the music and microphone volume. Using a powerful EQ, it can compensate for your music
or singer's shortcomings or when you would like to add more treble or bass to your performance. For music,
the 13 band frequencies are at 80Hz, 800Hz, 900Hz, 1kHz 1.2kHz,1.6 kHz,3.2 kHz,4.6 kHz,5.6 kHz,6.8 kHz,
7.2 kHz,8 kHz and 12 kHz. For the microphone, the frequency bands are at 35Hz-1kHz(10-Band in MLF),
500Hz-15 kHz(10-Band in MHF), 80Hz and 12kHz. You can fine tune each frequency to your desired level.
DESCRIPTIONS：
*Microphone Noise Gate- This powerful auto-mute function enables your mixer to automatically turn off the
microphone when it is not in-use. The powerful noise gate function allows a microphone signal to pass through
only when it is above the preset threshold value from 1 to 40. The mixer utilizes and advanced fading technique
to cut in and out of sound so you will not hear your microphone abruptly cut off once it has fallen below the
threshold or hear a loud click when the noise gate re-opens form mute.
*5 Microphone Inputs with 2 XLR Input Connectors- The SE-6000 includes 3 microphone inputs in the front
and 2 balanced audio connectors (XLR) for high quality microphone signal inputs form the rear. This XLR
connector allows for the use of long cables while reducing susceptibility to external noise. You can ensure
to transmit the upmost vocal signal to your SE-6000 Mixer using the XLR inputs. The rear inputs also enable
you to connect to most wireless microphone units while reducing the messy cables going from the front.
*Multiple-Channel Surround Sound Configuration- The SE-6000 has additional audio signal outputs for
center speaker (C)， sub-woofer (S)，and 2 rear speakers (SR). You can configure the mixer using one of
the many types of settings from 2.0 (L+R), 3.0(L+C+R), 2.1(L+R+S), 3.1 (L+C+R+S) AND 5.1(L+C+R+SR+
SL+S). Using one of the many surround sound configurations will help you create the enveloping effect inside
of a concert hall.
1 2
SE- 60 00

3 4
*User Lock-Down Mode- The mixer has built-in 'user lock' feature that can prevent most users from changing
any SE-6 000 's s ett ing. You can also define the maximum allowed volume for the music o r micro pho ne t o
prevent users form blowing out speakers. The SE-6 000 is designed to be used i n public places including
bars or karaoke rooms. This useful function will help you preserve the best sound quality I all occasions.
*Center Speakers and Rear Speakers Signal Control- When you enable the center speakers and surround
speakers, not only can you in dependently control it s vo lume, but you can also independent ly c ontrol the
balance between the music and vocal. Using the turning knob, you can fine tune if you want to hear only the
music, only the vocal, or a mix of music+ vocal from the center speaker or from the rear speakers.
*Subwo of er Si gnal Contr ol - S E-6000 h as 3 p ow erful subw oo fe r setting to f in e t une your subw oo fe r's
performance. You can adjust 1) Subwoofer Volume 2) Subwoofer LPF: the low-pass-filter ranges from 40 to
150 Hz enable you to decide how much of the low frequency signal should be coming from the subwoofer 3)
Subwoofer Volume Reducer: this function help you reduce subwoofer volume when you are singing. This
dynamic feature comes handy when a singer has low vocal range. SE-6000 will automatically reduce the
subwoofer volume to let the singer's voice comes out loud enough to be heard.
*Music and Microphone Balance- This powerful feature is designed for you to compensate for your irregular
roo m c onfiguration o r w hen your sp ea ke rs are not p la ced symmetri ca ll y form the a ud iences. Using t hi s
fun ct io n, you can e as il y adjust both th e m usic level an d e cho delay for each speaker to compensate f or
speakers that are further away from audiences.
*Auto -Source Detection- The SE-6000 has a built-in auto-source selection functions that enables the mixer
to automatically play music and video from one of the 3 available inputs. When the music stops, it will auto-
matically play the background A/V source (BGM) until the next song begins. This useful function will keep
your entertainment alive even when the performance ended and DJ is changing the disc for the next singer.
*8 Preset Memory Recall Program- You can save all of your optimal setting to preset memory inside. Audio
effects such as echo, reverb, music volume, and microphone volume can be recalled by either pressing the
button on the remote control or on the front panel. Once you have tuned and saved your favorite settings,
you will never need to adjust the mixer again.
*XLR Line Outputs- All of the SE-6000's line outputs i ncl udi ng Left, Right, Center and Sub woo fer audio
si gn al a re u sin g XLR B ala nce d Audi o Co nne ct ors to p res er ve t he c lea nes t s ign al t o your pro fes sio na l
amplifier.
FEATURES
1. MIC VOL
Master Microphone Volume Control –To control the master volume of microphone input from -70dB-+10dB
2. MUSIC VOL
Master Music Volume Control –To control the master volume of music input from -70dB-+10dB
3. MUSIC EQ
Equalizer for adjustment of music
LF：To adjust the gain of frequency below 80Hz , range is +-15dB.
MF: To adjust the gain of middle frequency, range is +-15dB.
MF: To adjust the point of middle frequency, rage is 800Hz-8KHz.
HF: To adjust the gain of frequency upper 12KHz , range is +-15dB.
4. BBE BOOST
To adjust the gain of bass of BBE effects.
5. MUSIC BALANCE
To adjust the balance of volume of LEFT and RIGHT music channel.
6. MIC LEVEL (1/A, 2/ B, 3)
1/A: use for adjusting the microphone volume of MIC 1 and MIC A on rear panel.
2/B: use for adjusting the microphone volume of MIC 2 and MIC B on rear panel.
3: use for adjusting the microphone volume of MIC 3 on front panel.
7. ECHO VOL / LPF
VOL: This knob is used for adjusting the master echo effect volume of microphone
LPF: This knob is used for adjusting the low pass filter of echo.
8. MIC EQ
1. LF: To adjust the gain of frequency below 80Hz , range is +-15dB.
2. MLF：To adjust the gain of selected middle-low frequency, range is +-15dB.
3. MLF: To adjust the point of middle-high frequency, range is 35Hz-1KHz.
4. MHF: To adjust the gain of corresponding middle-high frequency point, range is +-15dB.
5. MHF: To adjust the point of middle-high frequency, rage is 500Hz-15KHz.
6. HF: To adjust the gain of frequency upper 12KHz, range is +-15dB.
9. MIC INPUT JACKS (1,2,3)
Microphone jacks for MIC1,MIC2,MIC3
FRONT PANEL DE SC RI PT IO N
SE- 60 00

1. AC INPUT
AC power input
2. POWER SWITCH
Switch power on/off, I is power on, 0 is power off.
3. CONTROL
Line control input for external controller.
4. FUSE HOLDER
5. SUBWOOFER OUT
On：swi tc h of bass ou tp ut on/off, pres s t his butt on ON then t he re wil l b e not bas s s ignal ou tp ut fro m
MIX OUT terminal.
PROPORTIONAL: To adjust attenuation proportion of bass, used to adjust attenuation proportion of bass
when there is microphone input.
FREQ: to adjust the frequency of bass, frequency division range is 35Hz-250Hz.
VOLUME: to adjust the volume output of bass.
6. CENTER OUT
Output terminal of the center channel.
Volume: to adjust the level of center output volume.
Balance: to adjust the music and microphone mixing level output
7. REAR OUT
Volume: to adjust the level of rear output channel volume.
8. MIX OUT
Main channel output.
9. MUSIC INPUT
There are two sets of RCA input jack for VOD and BGM input.
10. MIC INPUT JACKS (A,B)
Jacks for microphone input
11. VIDEO IN
There are two sets of input jack (VOD, BGM) for video input.
12. VIDEO OUT
Video output for connecting TV.
REAR PANNEL DE SC RI PT IO N
1. LCD screen
The screen to show the setting and information.
2. REMOTE SENSOR
Please always face the remote sensor while using remote
controller.
4. ECHO MODE
DOWN: Used the previous Echo mode.
KTV/USER: used the KTV fixed echo modes (8 kinds of none- programmable mode) or use USER to edit
echo modes (8 kinds of programmable mode).
UP: Use the next Echo mode.
5. BBE BUTTON
Press this button to on or off BBE. Light on is ON BBE, light off is OFF BBE.
6. INPUT: audio input.
VOD: select to VOD audio input.
BGM: select to BGM audio input.
AUTO: select to VOD audio or BGM audio input automatically.
7. FBX
Press this button to on or off FBX(Feedback eliminator) . Light on is ON FBX, light off is OFF FBX.
8. MENU
Press this button to get into the menu edition mode.
Press ⑧ MENU then rotate ③ SETUP/ENTER to left or right to change the setting ,push to enter the sub-menu.
Model No. of the player will be displayed first. once power on, music volume, music input, mic volume and
echo mode will be displayed after system self-checking. Please follow the below instructions if you want to
change the settings:
MENU SETUP/ENTER
Press ⑧
MENU A (Volume setup) A1. Defaulted music volume setup.
A2. Max. music volume setup.
A3. Defaulted microphone volume setup.
A4. Max. microphone volume setup.
Press ⑧ again
MENU B (Echo setup) B1. Echo volume adjustment.
B2. Left channel delay adjustment.
B3. Right channel delay adjustment.
B4. Repeat times adjustment.
B5. Effects mix echo adjustment.
Press ⑧ again
MENU C (Effects setup) C1. To adjust the strength of effect
C2. Pre-delay adjustment, to adjust the first interval time of effect and vocal
C3. To adjust the wide of effect.
C4. To adjust the deep of effect.
C5. To adjust attenuation of effect.
Press ⑧ again
MENU D (Setting of lock) D1. Switch of Lock and unlock..
If Menu Lock is ON then you need to input passwords if you want to change the
setting next time.
Passwords Input buttons: Press “UP” twice then press “FBX” twice.
Press ⑧ to exit menu , system will save all setting data automatically.
DISPLAY SCRE EN F UN CT IO N DE SC RI PT IO N
5 6
3. SETUP/ ENTER
Function key: Press to confirm to enter in the next functions.
Turn left or right to adjust the gain (-70dB to +10dB) or state
(ON/ OFF).
Press ⑧ MENU to make indicator lighting first before operation.
SE- 60 00

7 8
Before using this equipment, please read through this handbook. For safe purpose, please observe all the
operation and usage warning which are written here and on the equipment.
1. Power: only the power source that indicated in the specification or the equipment can be used.
2. Power cord protect: pay attention to the usage of power cord, do not push, extrusion the cord.
3. Water and moisture: water cups, flower vases and other cases with water are not allowed to put on this
equipment and should not be sued near water placed such as bathtub, washing pool, kitchen sink, washtub,
wet basement, swimming pool and so on.
4. Heat: this equipment should be put far from heat source such as radiators, heating resistances, different
furnace and other heating equipment.
5. Electric shock: Prevent the matters and water get into the machines or it will case the inner electric shock.
6. Disassembly of cabinet: neve r di smantle, if you touch inner part of this equipment carel essly, s erious
electric shock will happen.
7. Keep it clean: Clean the equipment by soft and dry cloth, if the equipment is very dirty, please clean by
gentle cleaning agent but never clean by diluent paint, otherwise the top paint will be damaged.
8. Unusual odor: Unusual odor or smother found, please cut off power and take out the plug, please connect
with Supplier for repaired.
9. Operate the machine follow by the user manual.
10. If do not use it for a long time, please pull out the power cord.
WARNNING
DISPLAY SCRE EN F UN CT IO N DE SC RI PT IO N
Line Out
SNR（dB)
Distortion(%)
Standard input-signal level(V)
Standard output-signal level(V)
MAX. input-signal level(V)
MAX. output-signal level(V)
Difference of gain (L/R)
Channel Separation
Input impedance(Ω)
Output impedance(Ω)
Frequency response
Pitch adjustment range
Remote control/Line control
MICROPHONE
Sensitivity
SNR（dB)
Distortion(%)
Frequency response
Pitch adjustment range
Muting threshold level
OTHERS
Power Consumption
Packing dimension(W*D*H)
Product dimension(W*D*H)
Net Weigh (N.W)
Gross Weigh (G.W)
LEFT RIGHT CENTER BASS
90 90 88 87
0.03
0.020.010.01
0.775 0.775
0.8 0.8 0.775 0.8
3.5 3.5
4.2 4.2 4.2 4.5
less than 0.1
75dB
47K(Imbalance)
300(Balance)\1K(Imbalance)
10Hz-30KHz
80Hz(15dB), 12KHz(15dB)
Yes
25mV
87dB
0.03%
20Hz-20KHz
80Hz(15dB), 12KHz(15dB)
AGC
<25W
520*210*115(MM)
483*180*66(MM)
3Kg
3.2Kg