Santec Barosa 2429MC User manual

Installation Instruction
Wall Mount Widespread Lavatory Set
BAROSA COLLECTION
Please read the instructions completely before beginning the installation.
Barosa Collection
Model Number: 2429MC
Flush both supply lines before installation, then shut off both supply lines.
Minimum hole size for the spout and handle trim is 1-1/4” and maximum of 1-1/2”
NOTE:
- Where tile construction is planned for the finished walls, allow for
extra thickness dimensions when roughing in the valves.
- Test for proper function before closing walls.
- Determine where the finished wall will be. This measurement is
necessary to accurately plumb in the valve.
- Install the valve making sure that the measurement between the
center of the valve inlet and the outside of the finish wall is 2-3/4”. This
measurement is called the backset.
1
Rev 06/2016
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
- Using 1/2” IPS, connect the corner of the valves to the spout
base at the desired spread.
- Again, allow no more than 1-1/4” diameter holes for the spout and
handles.
2
1/6
ROUGH INSTALLATION
Center of Valve Inlet
Backset
Finished Wall

The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
2/6
NOTE: The length of threaded pipe coming out from the finish wall should be no
longer than 1/2”.
WARNING: Do not use excessive force when threading the spout.
- Wrap the pipe threading for the spout with teflon tape. Then, thread the spout onto
the pipe until it is secured with the spout facing downward.
SPOUT INSTALLATION
1Thread the bonnet nut, all thread, and insert the broach assembly
onto the valve and lightly tighten assembly with a 1” plumber’s
socket Wrench.
2
Thread the escutcheon completely onto the all thread ensuring
the broach properly engages the handle (orientation of the handle
is not important at this point)
4
Rethread the bonnet nut,all thread, and insert the broach
assembly back onto the valve and snugly tighten the assembly
with a 1” plumber’s socket wrench.
5
Ensure the valve is in the closed position and align the handle to
its respective “OFF” Position on the trim.
6
Thread the escutcheon on the handle onto the all thread and
broach assembly ensuring the handle position remains in the
closed position.
3
Measure the distance remaining between the handle base and
wall, remove all trim items from the valve, and cut the excess
distance from the end of the all thread and broach assembly.
HANDLE INSTALLATION
Diagram A
Bonnet Nut
Bonnet Nut
Finished Wall
All Thread

The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
PARTS DRAWING
3/6
* Please specify the finish when ordering the part.
4 6 11 5 15
9
1
10
8
7
12
3171421316
# PART DESCRIPTION PART #
1 Barosa WM WS handle flange PH00149
2 Barosa Wall Mount Tub Filler Spout Flange PH00150
3 Barosa Wall Mount WS Spout PS-6MC00-U-1
4 Valve Extension PM-1111
5 Valve Extension PM-1112
6 20T Broach Extension PM-007-1
7 Metra Classic Widespread Handle Bottom PH00142
8 Metra Classic Widespread Handle Top PH00141
9 Screw PM-509
# PART DESCRIPTION PART #
10 Teflon Washer PM-099
11 Stem Extension SA240
12 Belleville Washer PM-184
13 Screw #6-32 x 1-1/4" PM-179
14 Set Screw PM-508
15 Allen Wrench PM-205
16 Rubber Washer PM-400
17 M24 x 1 Neoperl Hidden Slim Laminar Stream PM-1245

SPECIFICATION SHEET
POP-UP
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
4/6
Ø 2
14
"
1
116
"3
516
"
12"
Ø 1
14
"
2
1
8
"
2
3
8
"
8
1
4
"
7
1
2
"
2
3
8
"
3
1
2
"

We recommend that all faucets, drains, etc., be gently wiped dry with a soft cloth after use to avoid water
spotting and water deposit build-up. A mild liquid hand soap may be used occasionally if desired. Use of a
non-abrasive carnauba wax will add protection to the finish and should be used if the faucets will not be dried
after use. For clear coated finishes, it is recommended to clean your product weekly with a soft moist cloth.
WARNING: Do not clean your SANTEC product with ammonia (Window cleaner), bleach, soap, acids,
abrasives, harsh polish, harsh cleaners, a coarse surfaced cloth, coarse sponge, or any type of scouring pad.
Doing so may ruin your faucet finish and/or void the warranty.
Thank you for making SANTEC a part of your lifestyle and luxury spa experience. Our products have been
created as works of enduring quality and sophisticated design.
Luxurious finishes need proper care and attention, so in order to understand how to properly clean your
distinctive luxury finish, please refer to the finish care information below:
Your SANTEC product can be identified in one of two categories: clear coated finishes or non-clear coated
finishes. Clear coated finishes are more scratch-sensitive and are more reactant to harsh cleaning chemicals
than non-clear coated finishes. Once you have identified the specific luxury finish of your SANTEC product,
please follow the important corresponding care instructions.
We recommend that all faucets, drains, etc., be gently wiped dry with a soft cloth after use to avoid water
spotting and water deposit build-up. A mild liquid hand soap may be used occasionally if desired. Use of a
non-abrasive carnauba wax is occasionally required and will add protection to the finish if the faucets will not
be dried after use.
FINISH CARE INFORMATION
CLEAR COATED FINISHES
NON-CLEAR COATED FINISHES
TO OBTAIN WARRANTY SERVICE
Please read ‘WHAT IS COVERED BY OUR WARRANTY’ and ‘EXCLUSIONS AND LIMITATIONS OF
WARRANTY’ sections to understand what is and what is not covered. Please have ready the proof of
purchase (original sales receipt), description of the problem, and carefully package the product or defective
part with postage prepaid. Then, please contact your local SANTEC Showroom or write to SANTEC Technical
Services.
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
5/6

LIFETIME LIMITED WARRANTY
SANTEC is committed to enhancing your bathroom experience by creating luxury products that will provide
enduring satisfaction. Every effort has been made to satisfy the highest standards of design and production,
to create lasting peace of mind for our customers. We provide the following limited warranties on our products:
LENGH OF WARRANTY & WHO IS COVERED BY OUR WARRANTY
This warranty extends to the original consumer purchaser only and extends for as long as the original
purchaser owns the product and the home in which the product is installed.
WHAT IS COVERED BY OUR WARRANTY
FINISHES: SANTEC Polished Chrome, Polished Nickel and Satin Nickel finishes carry a Lifetime Limited
warranty against manufacturing defects and tarnish to the original purchaser. All other finishes carry a ten
(10) year limited warranty against manufacturing defects and tarnish to the original puchaser only.
CARTRIDGES: Santec cartridges carry a lifetime limited warranty, with the exception of thermostatic and
pressure balanced cartridges, which carry a three (3) year limited warranty against manufacturing defects
to the original purchaser.
PARTS: Santec parts carry a 10-year limited warranty against manufacturing defects, to the original
purchaser.
EXCLUSIONS & LIMITATIONS OF WARRANTY
Damage due to negligence, accident, abuse, improper installation, or improper maintenance such as, but
not limited to: heat from soldering during installation, the use of plumber’s putty, damage from tools used
during installation, the use or exposure to chemicals or cleaning products either abrasive or non-abrasive,
or the use of any cleaning tool or product other than a soft, clean cloth. Reverse osmosis may also shorten
the life of the finish.
Changes in the finish or in the product due to normal wear or aging does not cover any products or parts
which have been altered or used in a manner not typical for the product.
Loss, damages, or expense, incidental or consequential whatsoever, originating from the purchase,
installation, use, repair, failure, or replacement of any SANTEC product or part, allowed by law.
This warranty does not cover:
Commercial and/or Industrial installations and use of the product.
This warranty does not include labor, travel charges, or any costs incurred for repair, removal, installation,
servicing, diagnosing, or handling of either defective or replacement parts.
SANTEC reserves the product components of the covered product will be repaired, refinished, or replaced
at the sole discretion of SANTEC. SANTEC reserves the right to examine any product claimed defective prior
to any warranty claim being accepted or processed, at its sole discretion. This warranty gives you specific
legal rights and you may have other rights which may vary from state to state.
The measurements shown are for reference only. Products and specifications shown are subject to change without notice.
www.santecfaucet.com | P: 310.542.0063 F: 310.542.5681
Damage or deterioration caused by environmental impacts.
6/6