Santec KLASSICA 9570KL User manual

KLASSICA COLLECTION
MODEL: 9570KL
KEEP THIS INSTRUCTION BOOKLET FOR FUTURE REFERENCE
Important : Please register your product online at www.santecfaucet.com within
30 days of purchase. Santec reserves the right to request additional documents
before servicing warranty requests.
0 1
MODEL: 9570KR
MODEL: 9570KT
BIDET

02
Vacuum Breaker
NOTE: See diagram on next page for removing and reinstalling the
complete trim.
Remove the complete trim from the Vacuum Breaker valve.
Insert Vacuum Breaker valve up from below and reinstall complete trim
except for the handle cap. Make sure to install the black plastic lock
nut in the position shown in the diagram on the next page. Snugly
tighten down the black plastic lock nut and trim cylinder by hand
tightening only.
until it stops. Pop the handle cap into the handle with the “spritzer”
icon facing frontwards or at the 6 o’clock position (see handle cap
diagram below).
supply lines.
Hole size for the spout and Handle Trim is a minimum of 1-1/4” and a
maximum of 1-1/2”.
Vacuum Breaker Installation
6
1 2
3
9
Spritzer
Handle Cap
9570 KL, KR, KT _ _

03
9570 KL, KR, KT _ _
Black plastic lock nut
Trim Cylinder
Handle
Screw
Handle Cap
Black Soft Seating China Seals
Black Soft Seating China Seals
White Nylon Slip Washer
Vacuum Breaker Valve
Elbow
Wye
Complete Trim

04
9570KL, KR, KT _ _
Handle Tr i m
Remove the Valve Body Mounting Hardware from the valve body. Slip
appropriate hole next to the vacuum breaker (HOT-left & COLD-right).
Apply a ring of silicone caulking around the handle hole on the bidet
top. DO NOT USE PLUMBER’S PUTTY, WHICH CAN DAMAGE FINISH.
Connecting Hoses toward Wye Connector.
For proper handle turning direction, install the handle with the “COLD”
blue label at the right side of the sink (front view) and the handle with
the “HOT” red label at the left side of thesink.
HANDLE TRIM IS READY FOR DROP-IN INSTALLATION. DO NOT
DISASSEMBLE HANDLE TRIM.
Handle Trim Installation (1)
Valve Body
Mounting Hardware
Washer
Brass Lock Nut
Wye connecting hoses

0 5
9570KL, KR, KT _ _
From beneath of the bidet, screw the Valve Body Mounting Hardware
back onto the valve body. First the washer, then the brass locknut.
Align the lever or cross handle properly against the vacuum breaker
the Inlet Hoses to the Supply Lines. Tighten to avoid leakage.
Handle Tr i m
Washer
Brass lock nut
Handle Trim Installation (2)
Inlet Hose
Supply Line

0 60 6
9570KL, KR, KT _ _
Sprit z e r
Apply a ring of silicone caulking around the hole designated for Spritzer
Slip Spritzer through the appropriate hole in bidet. From underneath
attach the Rubber Washer, Metal Washer and Shank Lock Nut. Tighten
Attach 24” hose from Spritzer to bidet elbow and tighten both ends
Spritzer Installation
Bidet
Basin
Rubber washer
Shank lock nut
Metal washer
Housin g
Basket
Wash e r
Spritzer Assembly
Spritzer
Front View

07
9570KL, KR, KT _ _
Pop U p Drai n
Remove Drain Flange and Drain Plug from pop-up assembly.
Apply a ring of silicone caulking to underside of Drain Flange. Do not use
Insert the threaded end of the assembly up from below and into thepop up
drain hole.
Completely thread the drain body into the Drain Flange and align with the Ball
Rod Hole facing back. Then tighten lock nut from below. Clean excess silicone
with paper towel.
Pop Up Drain Installation (1)
Drain Plug
Drain Flange
Ball Rod Hole
Gasket
Washer
Lock nut

08
9570KL, KR, KT _ _
Remove the Brass Lock Nut, Rubber Washer and Metal Washer from the
lift rod assembly. Inser t Lift Rod Flange into designated hole and
reassemble the Metal Washer, Rubber Washer and Brass Lock Nut from
below the bidet basin. Firmly tighten the Brass Lock Nut to secure Lift
Rod Flange.
Insert theLift Rod into Lift RodFlange from above.
Pop Up D rai n
PopUpDrainInstallation(2)
Metal Washer
Rubber Washer
Brass Lock Nut
Lift Rod
Lift Rod Flange

09
9570KL, KR, KT _ _
Insert Drain Plug into Drain Flange. Make sure the adjustable eye-screw
it.
Insert Ball Rod Washer into drain body followed by the Ball Rod, 2nd
Washer and Ball RodNut. Tighten the Ball Rod Nut until snug.
Gently push the Horizontal Ball Rod down to place the plunger in the
up position.
Connect the Lift Rod with the Ball Rod using the Pop-up connection and
tighten securely with screwdriver.
Test Pop-up for smoothoperation and adjust if necessar y.
Drain plug
Drain tube
Lift rod
Pop-up connection
Pop UpDr a i n
PopUpDrainInstallation(2)
Ball rod
assembly
(ball rod, ball rod
nut, & 2 washers)

10
9570KL, KR, KT _ _
Flu s h T h e Lin e
After all connections have been made from inlet supplies to angle
stops, remove Spritzer Housing, Basket and Washer (see Spritzer
Installation on page 5).
Open both hot and cold valves. Slowly open angle stops from below
Turn water off and reinstall Spritzer Housing, Basket and Washer.
INLET HOSEINLET HOSE