Sanus VMPL3B User manual

THANK YOU FOR CHOOSING SANUS
THE #1 TV MOUNT BRAND IN THE US.
VMPL3B Instruction Manual

2
VMPL3B
Lo haremos sin estrés
Si tiene preguntas mientras realiza la instalación, llámenos.
1-800-359-5520 Estamos listos para ayudarlo.
We’ll Make It Stress-Free
If you have any questions along the way, just give us a call.
1-800-359-5520 We’re ready to help!

3
2.95
75.00
MIN VESA
17.00
431.8
28.88
733.7
25.20
640.00
MAX VESA COLLAPSED
2.95
75.00
MIN VESA
17.13
435.00
MIN VESA EXPANDED
44.24
1123.7
40.55
1030.00
MAX VESA
15.75
400.00
MAX VESA
27.00
685.8
0.90
22.9
0.33
8.4
0.33
8.4
16.00
406.4
24.00
609.6
42.30
1074.4
9.02
229.1
5.00
127.00
3.75
95.3
6.00
152.4
3.00
76.2
16.00
406.4
16.00
406.4
12deg
DOWN
6deg
UP
2.50
63.5
17.00
431.8
3-D - COLLAPSED VIEW
FULLY ASSEMBLED MOUNT - COLLAPSED WALL PLATE - COLLAPSED
3-D - EXPANDED VIEW
SIDE VIEW
SIDE VIEW - TILT WALL PLATE - EXPANDED FULLY ASSEMBLED MOUNT - EXPANDED
Dimensions

4
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
Before getting started, let’s make sure this mount is perfect for you! Para Español ver página 25
No — Perfect!
Yes — This mount is NOT compatible. Visit MountFinder.Sanus.com or call
1-800-359-5520 to find a compatible mount.
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Also check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use
of this product, contact Customer Service at 1-800-359-5520
Do you have
all the tools
needed?
1
2
3
4
What is your
wall made of?
280 lbs.
(127 kg)
Ready to
begin?
Does your TV weigh
(including accessories)
more than 280 lbs.
(127 kg)?
CAUTION:
DO NOT install
into drywall alone
Unsure?
Drywall with
wood studs?
Solid concrete or
concrete block?
Call Customer Service:
1-800-359-5520
Perfect! Perfect!
Wood Stud Install
Concrete Install
Pencil Screwdriver
Tape
Measure
7/32 in.
(5.5 mm)
Wood
Drill Bit
Electric Drill Hammer
1/2 in.
(13 mm)
Socket
Wrench Drill Bit
3/8 in.
(10 mm)
Concrete
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed for use in wood stud, solid concrete, and concrete block walls - DO NOT install into drywall alone
●The wall must be capable of supporting five times the weight of the TV and mount combined
●Do not use this product for any purpose not explicitly specified by manufacturer
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use
Stud
Finder Awl

5
STEP 1 Select TV Hardware and Mount TV Brackets
2.5mm spacer
SPACER CUSTOM BLACK
M4X35
M5X35
M6X35
M8x25
M8X35
M8x50
M4/M5 Washer
M6/M8 Washer
THUMBSCREW 1024X03NP05
2.5 mm 22 mm
5.0 mm
M6 x 35mm
M8 x 16mm M8 x 25mm M8 x 35mm M8 x 50mm
M6 x 20mm
M6 x 12mm
5/16 in. x .075 in.
5⁄16 x 2 ¾ in.
UX10x60R
For concrete installations ONLY
3/16 in.
1/4 - 20 x 7/8 in.
NOTE: Not all hardware included will be used.
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged
item to Amazon; contact Customer Service. Never use damaged parts!
Parts and Hardware for STEP 1
04 x4
02 x4 03
01 x2
TV Bracket
TV Screws
TV Washers Spacers
x4x8 x4

6
M6 M8
1.1 Select TV Screw Diameter 1.2 Select TV Screw Length
Hand thread screws into the threaded inserts
on the back of your TV to determine which
screw diameter (M6 or M8) to use.
FLAT BACK ROUND BACK CABLES INSET HOLES
If your TV has a flat back AND you want your TV closer to the
wall, use the shorter screws.
Spacers and longer screws are supplied to accommodate:
●Round/irregular back TVs
●TVs with inset mounting holes
●Extra space needed for cables
Too Short
Too Long
CAUTION:
Verify adequate thread
engagement with the screw or
screw/spacer combination.
- Too short will not hold the TV.
- Too long will damage the TV.
Correct
If your TV included inset
spacers or wall mount
adapters, use them UNDER the
mount hardware.
ab

7
1.3 Attach TV Brackets
01
a
Lay your TV face-down on a soft surface. Position the TV brackets over your TV hole pattern, confirm the brackets are level on the back
of the TV, and install using TV screw and washer combination or you selected for your TV.
01
b
002812.eps
VMPL3 Tilting brackets at monitor
01
002815.eps
VMPL3 Tilting/Lowprole brackets curved
002812.eps
VMPL3 Tilting brackets at monitor
a Screw and washer
b Spacer, screw and washer
02
03
04
02
04
002812.eps
VMPL3 Tilting brackets at monitor

8
STEP 2 Determine Wall Plate Assembly Width
WARNING: This product contains
small items that could be a choking
hazard if swallowed.
Before starting assembly, verify all
parts are included and undamaged.
If any parts are missing or damaged,
do not return the damaged item to
Amazon; contact Customer Service.
Never use damaged parts!
05 x1
Wall Plate
.695 x .350 x.075 in.
3/16 in.
1/4 - 20 x 7/8 in.
5⁄16 x 2 3⁄4 in. UX10x60R
M6/M8
M6 x 35mm
M8 x 16mm M8 x 25mm M8 x 35mm M8 x 50mm
M6 x 20mm
M6 x 12mm
2.5mm
22mm 5mm
For concrete installations ONLY
Parts and Hardware for STEP 2
If the center to center TV bracket width is
9.45 inches (240mm) or greater, the expanded
wall plate can be used to complete a 3-stud
installation. Proceed to the 3-stud installation
process, step 3.
If the center to center TV bracket width is
9.41 inches (239mm) or less, the expanded
wall plate cannot be used. Proceed to the
collapsed/2-stud installation process, step 3.
NOTE: The collapsed wall plate should
be used for all 2-stud installations with TV
bracket widths up to 25.20 inches (640 mm).
Measure the center to center width between TV brackets on the back of your TV.
2.1 Measure TV bracket VESA width

9
STEP 2 Determine Wall Plate Assembly Width
05
1
2.2 Loosen the front wall plate (for 3-stud/slot installation only)
1. Remove the nuts N and washers W from the threaded studs A of the wall plate 05 .
2. Lift the center plate C of the wall plate 05 up and away from the back wall plates B .
N
W
A
2
B
CB

10
2.3 Extend back wall plates
Extend the back wall plates B based on the VESA pattern width of the
TV. This allows for a 3-stud installation. Use the slots on the center plate
to determine how far to extend the wall plates. Threaded studs A should
point up.
NOTE: Be sure the back wall plates B do not protrude from the sides
of the TV.
300mm (11.81 in) VESA
Center
Slots
34567 76543
Slots
Maximum Stud Distance
16.65” 16.65”
Slots
46
Slots
5 3
16” 16”
Slots
5 3
Slots
35
Minimum Stud Distance
B B

11
400mm (15.74 in) VESA 500 (19.68 in)/600mm (23.62 in) VESA
16” 16”
Slots
5 3
Slots
35
Minimum Stud Distance
16” 16”
Slots
5 3
Slots
35
Minimum Stud Distance
Maximum Stud Distance
18.45” 18.45”
Slots
57
Slots
6 4
Maximum Stud Distance
20.25” 20.25”
Slots
57
Slots
7 5

12
2.4 Tighten extended wall plate
After determining the correct width of the back wall plates B , gently set the front wall plate C down evenly over the threaded studs A .
Reattach the nuts N and washers W to the threaded studs A and tighten using 1/2 inch (13mm) socket.
CAUTION: To avoid personal injury or property damage, all four threaded studs A must be securely fastened to the front wall plate C .
CB
N
W
A
B

13
STEP 3 Mount the Wall Plate
2.5mm spacer
SPACER CUSTOM BLACK
M4X35
M5X35
M6X35
M8x25
M8X35
M8x50
M4/M5 Washer
M6/M8 Washer
THUMBSCREW 1024X03NP05
2.5 mm 22 mm
5.0 mm
M6 x 35mm
M8 x 16mm M8 x 25mm M8 x 35mm M8 x 50mm
M6 x 20mm
M6 x 12mm
5/16 in. x .075 in.
5⁄16 x 2 ¾ in.
UX10x60R
For concrete installations ONLY
3/16 in.
1/4 - 20 x 7/8 in.
Parts and Hardware for STEP 3
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and
undamaged. If any parts are missing or damaged, do not return the damaged item to Amazon; contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
05 x1
Collapsed Wall Plate
Washer
Anchors
.695 x .350 x.075 in.
3/16 in.
1/4 - 20 x 7/8 in.
5⁄16 x 2 3⁄4 in. UX10x60R
M6/M8
M6 x 35mm
M8 x 16mm M8 x 25mm M8 x 35mm M8 x 50mm
M6 x 20mm
M6 x 12mm
2.5mm
22mm 5mm
For concrete installations ONLY
Extended Wall Plate
NOTE: Only 4x lag bolts are needed for 2-stud/slot installations;
Only 6x lag bolts are needed for 3-stud/slot installations.
Lagbolts
06 x6
07 x6
08

14
CAUTION: Avoid potential personal injuries and property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1½ x
3½ in. (38 x 89 mm)
●Minimum horizontal space between fasteners: 16 in. (406mm)
●Stud center must be verified
1
Min. 3 1/2 in.
(89 mm)
Min. 1 1/2 in.
(38 mm)
STEP 3A Wood Stud Option
1. Verify the center of the stud(s) using an awl, a thin nail, or an edge
to edge stud finder.
NOTE: 2-stud width options = 16" to 24"
NOTE: 3-stud width options = 16" to 20.25"
Min. 16 in.
(406mm)
Max. 5/8 in.
(16 mm)

15
2. Place the assembled wall plate 05 at your desired height and position the slotted holes over your stud center line. Level the wall plate
05 and mark the hole locations.
NOTE: For assistance in determining wall plate location, see HeightFinder at SANUS.com.
IMPORTANT: Be sure you mark and drill into the center of the stud.
05
22-Stud Installation 23-Stud Installation
05
HEAVY! You may need assistance with this step.
4X
6X

16
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2 ¾ in. (70 mm).
NOTE: Drilling into 2 studs is only available for 16” to 24” stud spacing.
NOTE: Drilling into 3 studs is only available for 16” to 20.25” stud spacing.
32-Stud Installation 33-Stud Installation
2 ¾ in. (70 mm)
7/32 in. (5.5
mm)
4X
6X

17
4. Install and tighten lag bolts 06 only until the washers 07 are pulled firmly against the wall plate 05 .
CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage, DO NOT over-
tighten the lag bolts 06 .
05
42-Stud Installation 43-Stud Installation
05
06 07
06 07
4X
6X

18
CAUTION: Avoid potential personal injuries and property damage!
●Mount the collapsed wall plate 05 directly onto the concrete surface
●Minimum solid concrete thickness: 8 in. (203 mm)
●Minimum concrete block size: 8 x 8 x 16 in. (203 x 203 x 406 mm)
1. Position the collapsed wall plate 05 on the wall at your desired height. Level the wall plate 05 and mark the hole locations.
NOTE: For assistance in determining wall plate location, see Height Finder at sanus.com.
NOTE: 24 in. installation spacing shown.
05
STEP 3B Solid Concrete or Concrete Block Option
1

19
Solid Concrete or Concrete Block Option
2. Drill pilot holes using a 3/8 in. (10 mm) diameter drill bit.
IMPORTANT: Pilot holes must be drilled to a depth of 2 ¾ in. (70 mm). Never drill into the mortar between blocks.
3. Insert lag bolt anchors 08 .
NOTE: Be sure the anchors 08 are seated flush with the concrete surface.
2
3/8 in.
(10 mm)
3 in. (75 mm)
002862.eps
3
08

20
05
4
07
06
06
4. Insert lag bolts 06 through the washer 07 , wall plate 05 , and into the anchors 08 .
CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage:
●Tighten the lag bolts 06 only until the washers 07 are pulled firmly against the wall plate 05 .
●DO NOT over-tighten the lag bolts 06 .
07