Sanus OLF22-B2 User manual

OLF 22-B2
INSTRUCTION MANUAL
FULL-MOTION
TV WALL MOUNT

2
125 lbs.
(56.6 kg)
IMPORTANT SAFETY INSTRUCTIONS – PLEASE READ MANUAL PRIOR TO USE – SAVE THESE INSTRUCTIONS
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product,
contact Customer Service: U.S.: 800-359-5520 • EMEA: [phone] •UK: 0800 056 2853
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed ONLY to be installed into wood studs, solid concrete or concrete block.
—DO NOT INSTALL INTO DRYWALL ALONE — DRYWALL ALONE WILL NOT HOLD THE WEIGHT OF YOUR TV.
●This product is designed for INDOOR USE ONLY.
●The wall must be capable of supporting five times the weight of the TV and mount combined.
●Do not use this product for any purpose not explicitly specified by manufacturer.
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
TV Weight Limit
(including accessories)
DO NOT EXCEED
If your TV (plus accessories) weighs MORE, this
mount is NOT compatible.
Visit SANUS.com or call customer service to find a
compatible mount. U.S.: 800-359-5520
• EMEA: [phone] •UK: 0800 056 2853
Texto en español, página 20 Deutscher Text Seiten 26 Svensk text sida 32
中文文字说明请参见第 38 页
Texte français page 23 Nederlandse tekst op pagina 29
Русский текст: стр. 41
日本語は 35 ページ

3
Tools Needed
Wall
Construction
ONLY install on
these acceptable
wall types. Drywall alone will
NOT hold the weight
of your TV.
wood studs Solid concrete or
concrete block
ACCEPTABLE ACCEPTABLE
Wood Stud Install
Concrete Install
Awl
Pencil Level Tape
Stud
Finder
ScrewdriverTape
Measure
7/32 in.
(5.5 mm)
Wood
Drill Bit
Electric
Drill
Hammer
1/2 in.
(13 mm)
Socket
Wrench
Drill Bit
3/8 in.
(10 mm)
Concrete
CAUTION:
DO NOT install
in drywall alone
Call Customer Service
U.S.: 800-359-5520
P: [phone]
UK: 0800 056 2853
Unsure

4
0.35in
9mm
15.98in
406mm
0.87in
22mm
9.00in
228.5mm
7.62in
193.5mm
5.31in
135mm
5.31in
135mm
25.91in
658mm
17.13in
435mm
35deg
35deg
2.53in
64.2mm
9.24in
234.6mm
7.89in
200.4mm
22.00in
558.8mm
15deg
DOWN
8deg TILT
SIMULATED 70"
FLAT SCREEN TV
WALL PLATE TOP VIEW - SWIVEL
3-D
SIDE VIEW - EXTENSION/TILT
SIDE VIEW - RETRACTED FRONT VIEW - TILT FULLY ASSEMBLED MOUNT
WALL IS ON RIGHT
WALL IS ON RIGHT
WALL IS ON TOP
WALL IS ON TOP
15.75in
400mm
MAX
23.62in
600mm
MAX
7.87in
200mm
MIN
TV INTERFACE
MIN
200mm
7.87in
Dimensions

5
5/16 in.
5/16 x 2¾ in.
M5 x 8mm
M5
M6/M8
2.5mm
5mm
22mm
M8 x 50mm
M6 x 12mm
M6 x 35mmM6 x 20mm
M8 x 20mm M8 x 40mm
M8x30 mm
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to
Amazon; contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
STEP 1 Parts and Hardware
TV Screws
(qty. 4 each)
[Only one size fits your TV]
M6
M8
Washer
(qty. 4 each) Spacers (qty. 4 each)
[If necessary]
03
02
01 Vertical TV Bracket
Horizontal TV Bracket
Wing Nuts
M5
05
04 qty. 1
qty. 2
06 qty. 4
Dimensions
Shipped Attached

6
5/16 in.
5/16 x 2¾ in.
M5 x 8mm
M5
M6/M8
2.5mm
5mm
22mm
M8 x 50mm
M6 x 12mm
M6 x 35mmM6 x 20mm
M8 x 20mm M8 x 40mm
M8x30 mm
Wall Plate Assembly
Wall Plate Template
Lag Screw
09
07
08
10
Washer [Lag Screw]
STEP 2 Parts and Hardware
qty. 1
qty. 4
qty. 4
qty. 1
Concrete Anchor
For concrete installations ONLY
CAUTION:
Do not use in drywall or wood
(qty. 4)
11

7
Securement Screw
Washer [Securement Screw]
Hex Key
Cable Ties
12
13
14
15
STEP 3 Hardware Installation / Adjustments
qty. 1
qty. 1
qty. 1
M4
qty. 4
5/16 in.
5/16 x 2¾ in.
M5 x 8mm
M5
M6/M8
2.5mm
5mm
22mm
M8 x 50mm
M6 x 12mm
M6 x 35mmM6 x 20mm
M8 x 20mm M8 x 40mm
M8x30 mm

8
STEP 1 Attach TV Bracket to TV
Inset Holes Cables Rounded Back
Only one screw size fits your TV.
M6 M8 • Flat Back TV
[TV brackets
lay flat on your TV]
NO SPACER SPACER NEEDED
• Flat Back TV with
Extra Space Needed
[for deep inset holes
or cable interference]
• Rounded or
Irregular Back TV
[TV brackets NOT
resting flat on your TV]
A B
Use short TV screws 01 .
Spacers 03 not needed. Use long TV screws 01 and spacers 03 to
create extra space between the TV and TV bracket.
01
CAUTION: Verify adequate thread engagement with your
screw 01 , washer 02 , spacer 03 combination AND TV bracket 05 .
—Too short will not hold your TV. —Too long will damage your TV.
Too Short
Too Long
Correct
1.2 Select TV Screw Length and Spacers1.1 Select TV Screw Diameter

9
1.3 Attach TV Brackets to Your TV
inch dimensions are approximate
inches cm mm
7⅞20 200
11 ¾ 30 300
15 ¾ 40 400
23 ¾ 60 600
1 2
H
H
H
Hmm = 200 mm
> 200 mm
05
05
04
06
05
05 05
05
04

10
3
04
Screw
posts
05
05
04
4
05
TV HOLE
PATTERN
TOP OF TV
05
04
= 200 mm
H
H

11
06
5
03 02
02
01
01
6
Center the TV bracket assembly over your TV's hole pattern and attach using
screw combination Aor Byou selected for your TV.
CAUTION: Avoid potential personal injuries and property damage! DO NOT
use power tools for this step. Tighten the screws 01 only enough to secure the TV
brackets to the TV.
05
06
05
04
NO SPACER
SPACER NEEDED
A
B

12
12
MIN.
16 in.
(406 mm)
STEP 2A Attach Wall Plate Wood Stud Installation
MAX 5/8 in. (16 mm)
CAUTION: Avoid potential personal injury or property damage!
●Drywall covering the wall must not exceed 5/8 in. (16 mm)
●Minimum wood stud size: nominal 2 x 4 in. (51 x 102 mm) actual 1 ½ x 3 ½ in. (38 x 89 mm)
●Minimum horizontal space between fasteners: 16 in. (406 mm)
●Stud centers must be verified
07

13
09
3 4
10
Install the wall plate 08 using four lag bolts 09 and washers 10 .
CAUTION: Improper use could reduce the holding power of the lag
bolt 09 . Tighten all lag bolts 09 only until the washers 10 are pulled firmly
against the wall plate.
DO NOT over-tighten the lag bolts 09 .
Go to STEP 3 on PAGE 16.
07 08
7/32 in.
(5.5 mm)
2¾in. (70 mm)
4X
4X

14
CAUTION: Avoid potential personal injury or property damage!
●Mount the wall plate assembly 08 directly onto the concrete surface
●Minimum solid concrete thickness: 8 in. (203 mm)
●Minimum concrete block size: 8 x 8x 16 in. (203 x 203 x 406 mm)
●Minimum horizontal space between fasteners: 16 in. (406 mm)
12
MIN.
16 in.
(406 mm)
002862.eps
STEP 2B Attach Wall Plate
Solid Concrete or Concrete Block Installation
07
07
3/8 in.
(10 mm)
3 in. (75 mm)
4X

15
34
08
09
10
11
Install the wall plate 08 using four lag bolts 09 and washers 10 into the
cocrete anchors 11 .
CAUTION: Improper use could reduce the holding power of the lag bolt
09 . Tighten all lag bolts 09 only until the washers 10 are pulled firmly against
the wall plate. DO NOT over-tighten the lag bolts 09 .
4X
4X

16
HEAVY! You may need assistance with this step.
STEP 3 Hang TV onto Wall Plate
CAUTION! Avoid potential personal injuries and property damage!
Screw 12 and washer 13 must be installed to secure your TV onto the wall plate assembly 08 .
DO NOT use power tools for this step. Tighten the screw 12 only enough to secure the TV.
1 2
08
04
12
13
CAUTION: Avoid potential personal injuries and property
damage! DO NOT use power tools for this step. Tighten the
screws 01 only enough to secure the TV brackets to the TV.

17
STEP 3 Hang TV onto Wall Plate Manage Cables
IMPORTANT: Fully extend the arms before routing cables.
08
15

18
TV Adjustments
TILT LEVEL
1. Loosen the tilt lever T.
2. Adjust the TV tilt position.
3. Tighten tilt lever Tto secure the TV in place
at your desired tilt angle.
NOTE: If needed, tighten screw T2for
additional tilt tensioning.
T2
T
Tighten
Tighten
Loosen
Loosen
1. Loosen the screw 12 on the rear of wall plate assembly 08 .
2. Level your TV.
3. Retighten screw 12 to secure in place.
Tighten
Loosen
14
08
08
12
CAUTION! Avoid potential personal injuries and property damage!
Screw 12 and washer 13 must be installed to secure your TV onto the
wall plate assembly 08 .
DO NOT use power tools for this step. Tighten the screw 12 only enough
to secure the TV.

19
TV Adjustments
REMOVING THE TV
To remove your TV from the wall plate assembly 08 :
1. Disconnect all cables.
2. Remove screw 12 and washer 13 .
3. Lift the TV up and off of wall plate assembly 08 .
HEAVY! You may need assistance with this step.
3
2
108
12
13

20
INSTRUCCIONES IMPORTANTES DE SEGURIDAD: GUARDE ESTAS INSTRUCCIONES Y
LEA TODO EL MANUAL ANTES DE UTILIZAR ESTE PRODUCTO.
ESPAÑOL
Antes de empezar, asegúrese de que este es el soporte adecuado para usted.
1 ¿Su televisor pesa más de 56,6 kg (125 lb), incluidos los accesorios?
No. ¡Perfecto!
Sí. Este soporte NO es compatible. Visite SANUS.com o llame al servicio de atención al cliente (consulte la cubierta trasera)
para encontrar un soporte compatible.
2 ¿De qué
está hecha
la pared?
3 ¿Tiene todas las
herramientas
necesarias?
4 ¿Preparado para empezar?
Lea atentamente estas instrucciones en su totalidad para asegurarse de que está familiarizado con el sencillo proceso de instalación. Consulte
igualmente el manual de su televisor para conocer si existen requisitos especiales para el montaje de su aparato.
Si no entiende las instrucciones o si tiene dudas acerca de la seguridad de la instalación, el montaje o el uso del producto, póngase en contacto
con el servicio de atención al cliente (consulte la cubierta trasera).
PRECAUCIÓN: ¡Evite posibles lesiones personales y daños materiales!
●Este producto se ha diseñado para usarse en montantes de madera, hormigón macizo y paredes de bloques de hormigón: NO lo instale en
paredes únicamente de yeso
●La pared debe ser capaz de soportar hasta cinco veces el peso combinado del televisor y el soporte
●No utilice este producto para ningún otro propósito que no sea el explícitamente especificado por el fabricante
●El fabricante no se responsabiliza de ningún daño o lesión resultante del montaje incorrecto o el uso indebido del producto
56,6 kg
(125 lb)
Instalación en
montantes de madera
Instalación en
hormigón
Cinta
métrica Lápiz Nivel Destornillador Taladro eléctrico Llave de tubo Localizador
de montantes Punzón Broca para madera Broca para mampostería Martillo
13 mm
(1/2 pulg.) 5,5 mm
(7/32 pulg.)
10 mm
(3/8 pulg.)
¿Hormigón
macizo o bloque
de hormigón?
¿Paneles de yeso
con montantes
de madera?
PRECAUCIÓN:
NO instalar
en paredes
únicamente de yeso
¿No está seguro?
Llame al servicio de atención
al cliente (consulte la
cubierta trasera)
?
¡Perfecto! ¡Perfecto!