Sanus BMF320 User manual

BMF 320
INSTRUCTION MANUAL
Texto en español, página 13
GET IT
RIGHT
THE FIRST TIME
Follow this step-by-step
instruction manual to
speed up your installation.
WE’RE HERE TO HELP
Our US-based install experts
are standing by to help.
Call us at:
800-359-5520
Or, chat at:
SANUS.com/chatSP
Get it right the first time.
HeightFinder™ shows you
where to drill.
Check it out at:
SANUS.com/1172
Want to watch a video that
shows how easy this DIY
project will be?
Watch it now at:
SANUS.com/2782

2
Wood Stud Install
Concrete Install
Awl
Pencil Level Tape
Stud
Finder
ScrewdriverTape
Measure
1/8 in.
(3 mm)
Wood
Drill Bit
Electric
Drill
Hammer
7/16 in.
(11 mm)
Socket
Wrench
Drill Bit
3/8 in.
(10 mm)
Concrete
55 lbs.
(24.9 kg)
IMPORTANT SAFETY INSTRUCTIONS – PLEASE READ MANUAL PRIOR TO USE –
SAVE THESE INSTRUCTIONS
Please read through these instructions completely to be sure you’re comfortable with this easy install process.
Check your TV owner’s manual to see if there are any special requirements for mounting your TV.
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product,
contact Customer Service 1-800-359-5520.
CAUTION: Avoid potential personal injuries and property damage!
●This product is designed ONLY to be installed into wood studs, solid concrete or concrete block.
— DO NOT INSTALL INTO DRYWALL ALONE — DRYWALL ALONE WILL NOT HOLD THE WEIGHT OF YOUR TV.
●This product is designed for INDOOR USE ONLY.
●The wall must be capable of supporting five times the weight of the TV and mount combined.
●Do not use this product for any purpose not explicitly specified by manufacturer.
●Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
TV Weight Limit
(including accessories)
DO NOT EXCEED
If your TV (including accessories) exceeds
this weight, this mount is NOT compatible.
Visit SANUS.com or call customer service to
find a compatible mount.
1-800-359-5520
Call Customer Service
1-800-359-5520
Tools Needed
Wall
Construction
ONLY install on
these acceptable
wall types. Drywall alone
will NOT hold
the weight of
your TV.
Unsure
wood studs Solid concrete or
concrete block
ACCEPTABLE ACCEPTABLE
CAUTION:
DO NOT install
in drywall alone

3
7/16 in.
(11 mm)
16.28
413.4
15.75
400.0
16.40
416.6
18.03
458.0
0.38
9.7
3.94
100.0
3.94
100.0
11.39
289.3
2.59
65.8
0.33
8.4
13.03
331.0
15.93
404.5a
2.46
62.5
OFFSET
20.00
508.1
60.00°
SIMULATED 49"
FLAT SCREEN TV
15°
5°
2.04
51.8
TV INTERFACE
WALL PLATE
FULLY ASSEMBLED MOUNT
TOP VIEW - EXTENDED
TOP VIEW - RETRACTED
SIDE VIEW - EXTENDED
SIDE VIEW - RETRACTED
3-D
Dimensions
BEFORE YOU BEGIN
Remove the stand
from your TV — if attached.
Install any accessories
you may have purchased, if they
requireTV removal prior to assembly.
The TV is removable for future
accessory purchases.
Soft clean surface
Protect the face
of your TV when laying it
down for installation.

4
• Flat Back TV
[TV brackets lay flat on your TV]
NO SPACER SPACER NEEDED
A B
Only one screw size fits your TV.
M6 M8
01
Use short TV screws 01 .
Spacers 03 not needed.
STEP 1 Attach TV Bracket to TV
Use long TV screws 01 and spacers 03 to create
extra space between the TV and TV bracket.
• Flat Back TV with extra space needed
[for deep inset holes or cable interference]
• Rounded or Irregular Back TV
[TV brackets NOT resting flat on your TV]
CAUTION: Verify adequate thread engagement with your screw 01 ,
washer 02 , spacer 03 combination AND TV bracket 06 .
— Too short will not hold your TV. — Too long will damage your TV.
1.2 Select TV Screw Length and Spacers1.1 Select TV Screw Diameter
NOTE: If your TV
included inset spacers
or adapters, use them
UNDER the mount
hardware.
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included
and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts!
NOTE: Not all hardware included will be used.
M4
M8 x 35mm
M8 x 16mm
M5 x 10mm
M6 x 12mm M6 x 35mm
M4 x 12mm M4 x 35mm
M8 x 50mm 22mm
2.5mm
5mm
M8 x 25mm
STEP 1 Parts and Hardware
TV Screws
(qty. 4 each) [Only one size fits your TV]
Washers
(qty. 4 each)
Spacers
[If necessary]
(qty. 4 each)
03
02
01
M6/M8
M4/M6/M8
M6
M4
M4
M8
(qty. 1)
04
(qty. 4)
05
(qty. 2)
06
TV Bracket Vertical
Interface Screw
TV Bracket
Horizontal
MOUNTING TABS
(ATTACHED)
RELEASE CORD
(ATTACHED)
MOUNTING TABS
M
R

5
1.3 Attach TV Brackets to Your TV
TV Bracket
Horizontal
W
Adjust mounting tabs M on TV brackets 06 to match the width W
of your TV's mounting hole pattern.
300 mm position illustrated
2ADJUST TO WIDTH W
Measure the WIDTH and HEIGHT of your TV's mounting hole pattern.
1MEASURE
inch dimensions are approximate
W
H
06
M
M
inches cm mm
410 100
7⅞20 200
11 ¾ 30 300
15 ¾ 40 400
inches
cm
mm
4
10
100
7
⅞
20
200
11 ¾
30
300
15 ¾
40
400
W
H
mm
mm
inches
For height 200 mm or less For height greater than 200 mm
For hole pattern height H greater than 200 mm, align horizontal TV
brackets 06 with mounting tabs M to the outside.
For hole pattern height H 200 mm and less, align horizontal TV
brackets 06 with mounting tabs M to the inside.
3a ASSEMBLE FOR HEIGHT H3b ASSEMBLE FOR HEIGHT H
≤ 200 mm > 200 mm
04 04
06
06
06 06
MM

6
TV bracket 04 must be centered on your TV, but can be offset up or
down to avoid cable interference.
5CENTER
Adjust TV brackets 06 to align with your TV hole pattern. Install using the
screw 01 /washer 02 /spacer 03 combination you selected for your TV.
04
06
4LOOSELY ASSEMBLE
4X
06
06
01
02 02
03
01
NO SPACER SPACER NEEDED
A B
Secure the TV brackets using four interface screws 05 , starting with
the top two screws in the notches shown.
6SECURE ASSEMBLY
2X
05
2X
05
05
2X
0505
Securely tighten the screws from STEP 4 and STEP 6.
7TIGHTEN ALL SCREWS
8X
01
05
a
b

7
Attach Wall Plate to Wall
STEP 2
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are
included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
Never use damaged parts!
NOTE: Not all hardware included will be used.
Fischer UX10 x 60R
1/4 x 2¾ in.
1/4 in.
09 x2
10 x2
07 x1 08 x1
11
x2
Parts and Hardware for STEP 2
Lag Bolt Washer
Arm Assembly
Wall Plate
Template
Concrete Anchor
0
For concrete installations ONLY
CAUTION: Do not use in drywall or wood
CABLE COVERS
(ATTACHED)
C
x2
WALL PLATE
COVER
(ATTACHED)
P
For WOOD STUD
INSTALLATIONS
For CONCRETE
INSTALLATIONS
Follow 2A on PAGE 8
Follow 2B on PAGE 9
For
WOOD STUD
INSTALLATIONS
Follow 2A on PAGE 8
For
CONCRETE
INSTALLATIONS
Follow 2B on PAGE 9

8
STEP 2A Attach Wall Plate Wood Stud Installation
Min. 3 ½ in. (8.9 cm)
Min. 1 ½ in. (3.8 cm)
Max. 5/8 in. (1.5 cm)
CAUTION: Avoid potential personal injury or property damage!
●Drywall covering the wall must not exceed 5/8 in. (1.5 cm)
●Minimum wood stud size:
nominal 2 x 4 in. (5.1 x 10.2 cm) actual 1 ½ x 3 ½ in. (3.8 x 8.9 cm)
●Stud center must be verified
1LOCATE STUD 2VERIFY 3MARK
2X
2X
2 ¾ in. (7.0 cm)
1/8 in.
(3 mm)
5DRILL
CAUTION:
Be sure you drill into the
CENTER of the stud.
07
6REMOVE COVERS
08
P
P
TIP:
To calculate your precise wall plate location,
check out our HeightFinder at sanus.com
[www.sanus.com/1172].
sanus.com
/1172
HeightFinder™
Visit
4POSITION TEMPLATE
7SECURELY TIGHTEN 8INSERT COVERS
2X 08
09
Go to STEP 3 on PAGE 10.
P
P
TIP: You can make small
level adjustments by loosening
the bottom lag bolt 09 and
shifting the wall plate until level.
Both lag bolts 09 MUST BE firmly tightened to prevent unwanted
movement of arm assembly 08 . Ensure the wall plate is securely
fastened to the wall before continuing on to the next step.
CAUTION: Avoid potential personal injury or property damage!
09
10
08

9
Solid Concrete or Concrete Block Installation
STEP 2B Attach Wall Plate
●Mount the arm assembly 08 directly
onto the concrete surface (no surface
covering)
●Minimum solid concrete thickness:
8 in. (20.3 cm)
●Minimum concrete block size:
8 x 8 x 16 in. (20.3 x 20.3 x 40.6 cm)
CAUTION: Avoid potential personal
injury or property damage! sanus.com
/1172
HeightFinder™
Visit
TIP:
TIP: To calculate your precise wall plate location, check out our HeightFinder at
sanus.com [www.sanus.com/1172].
07
1POSITION TEMPLATE
CAUTION:
Never drill into the mortar
between blocks.
2DRILL
2X
CAUTION:
3/8 in.
(10 mm)
3 in. (7.5 cm) 4REMOVE COVERS
08
P
P
14
3
2X
CAUTION:
Be sure the anchors 11 are seated
flush with the concrete surface.
CAUTION:
11
3INSERT ANCHORS
5SECURELY TIGHTEN 6INSERT COVERS
2X
08
09
P
P
TIP: You can make small
level adjustments by loosening
the bottom lag bolt 09 and
shifting the wall plate until level.
Both lag bolts 09 MUST BE firmly tightened to prevent unwanted
movement of arm assembly 08 . Ensure the wall plate is securely
fastened to the wall before continuing on to the next step.
CAUTION: Avoid potential personal injury or property damage!
09
10
08

10
WARNING: Before starting assembly, verify this part is
undamaged. If damaged, do not return the damaged item to your dealer;
contact Customer Service. Never use damaged parts!
Attach TV to Wall Plate
STEP 3
Hang the TV onto the arm assembly 08 by hooking the top support
on TV bracket 04 as shown.
1HANG YOUR TV
HEAVY! You may
need assistance
with this step.
04
08
12
To lock the TV onto arm assembly 08 , install the securement
screw 12 on the vertical TV bracket 04 using hex key 14 .
Always make sure your securement screw 12 is tightened, so
the TV is securely fastened to the arm assembly 08 .
CAUTION: Avoid potential personal injury or property damage!
3SECURELY TIGHTEN
04 08
14
08
Press the bottom of the TV into the arm assembly 08 until you hear
the lock click, securing the TV in place.
2ATTACH
04
3/32 in.
5/32 in.
10-32 x 1/4 in.
Parts and Hardware for STEP 3
Hex Key
Hex Key
12
x1
13
x1
14
x1
Securement
Screw
NOTE: TV shifts 2.4 in. (6.2 cm) to the right or left when in the home
position. Consider this when selecting the location of your wall mount.