Sanus San213 User manual

Sanus Systems 2221 Hwy 36 West, Saint Paul, MN 55113 USA

Customer Service: 1-800-359-5520 • 651-484-7988

[email protected]om • www.accents.sanus.com

are registered trademarks, and Sanus Accents and the Sanus Accents logo are trademarks of Milestone.

All other brand names or marks are used for identification purposes and are trademarks of their respective owners.

SAN213

(6904-100136 <00>)

Thank you for choosing an Accents wall mount.The SAN213 is designed to mount monitors with VESA 75x75, 100x100,

or 200x100 hole patterns, weighing less than 45 lbs (20.5 kg) to a vertical wall; it is also adjustable, allowing ±15° of tilt.

Do not use this product for any purpose not explicitly specied by Accents. Improper assembly may cause

property damage or personal injury. If you do not understand these directions, or have doubts about the safety

of the assembly, contact Customer Service or call a qualied contractor. Accents is not responsible for damage or

injury caused by incorrect assembly or use.

CAUTION

This product contains small items that could be a choking hazard if swallowed. Keep these items away

from young children!

WARNING

OPT

Hardware and procedures for multiple mounting configurations are included.When you see this symbol,

choose the correct configuration to suit your needs. Not all hardware included will be used.

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS

The wall must be capable of supporting up to five times the weight of the monitor and mount combined. If you

have any doubts about the ability of the wall to support the monitor, contact Customer Service, or a qualified

contractor.

CAUTION

6904-100136 <00>

Supplied Parts and Hardware

Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item

to your dealer; contact Customer Service. Never use damaged parts!

3/8 in.

3/16 in.

[11] x 4

[06] x 1

[01] x 1

[18] x 1

[07] x 1

[17] x 4

[02] x 1

[03] x 2 [04] x 2 [05] x 1

[08] x 1 [09] x 1 [10] x 2

[12] x 4 [13] x 4 [14] x 2 [15] x 4 [16] x 8

1/4-20 x 3.25 in.

M8 0.5 in. 0.5 in.

M4 x 30mm M4 / M5 8-32 x 0.5 in.

M4 x 10mm

6904-100136 <00>

1-1: Wood Stud Mounting

3/16 in.

Do not over-tighten the lag bolts

[03]. Tighten the lag bolts [03]

only until they are pulled against

the wall plate [01].

CAUTION

Any material covering the wall must not

exceed 13 mm (1/2 in.).

CAUTION

Use awl to verify stud location.

NOTE

[01]

[03]

64 mm

(2.5 in.)

6904-100136 <00>

1-2: Concrete Block Mounting

3/8 in.

Do not over-tighten the lag bolts

[03]. Tighten the lag bolts [03]

only until they are pulled against

the wall plate [01].

CAUTION

For concrete block walls, install

the fasteners into the face of the

block. Never drill into mortar

between blocks. Ensure the

anchors [04] seat ush with the

block.

CAUTION

[01]

[03]

[04]

6904-100136 <00>

2-1: TV with Flat Back

[02]

[11]

[13]

[02] [12]

2-2: TV with Curved Back or Obstruction

6904-100136 <00>

[05]

[10]

[09]

[06]

[07]

[08] [01]

3: Attach Head to Arm Assembly

[18]

[02]

6904-100136 <00>

[16]

[02] [16]

[01]

[16]

6904-100136 <00>

[17]

[15]

[14]

Pull the arm to its full extension

then route the cables through

the arm, leaving enough slack

to prevent stretching the cables

when the arm is moved.

6904-100136 <00>

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively,“Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information

contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product.The information contained in this document is

subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein.Milestone assumes no responsibility for