Sanus SAN55BA User manual

Customer Service
Americas: 800-359-5520 • 651-484-7988 • [email protected]om
Europe, Middle East, and Africa: + 31 40 2324700 • [e-mail]
Asia Pacific: 86 755 8996 9226 • [e-mail]
SANUS · 2221 Hwy 36 West · Saint Paul, MN 55113 USA
©2011 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone.
All other brand names or marks are used for identification purposes and are trademarks of their respective owners.
We are here to help!
Please contact Customer Service with any questions.
accents.sanus.com
(6904-002015 <01>)
SAN55BA Instruction Manual

6904-002015 <01>
2
Specications
Weight capacity--DO NOT EXCEED: 58.9 kg (130 lbs) includes TV, mount, and any accessories
CAUTION: Avoid potential personal injuries and property damage!
Do not use this product for any purpose not explicitly specied by Sanus Systems.
The wall must be capable of supporting ve times the weight of the monitor and mount combined.
This product is not designed for use in metal stud walls!
If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this
product, contact manufacturer Customer Service or call a qualied contractor.
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE
484.1 mm
19.06 in.
177.8 mm
7.0 in.
736.6 mm
29 in.
50 mm to 758 mm
450 mm
17.72 in.
26.5 mm
1.05 in.

6904-002015 <01> 3
Required Tools
Supplied Parts and Hardware
WARNING: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the
damaged item to your dealer; contact Customer Service. Never use damaged parts!
NOTE: M4, M6, or M8 describes the diameter, mm describes the length of screws that are labeled M# x ##mm. Not all
hardware included will be used.
5.5mm
(7/32 in.)
13mm
(1/2 in.)
13mm
(1/2 in.)
M4 x 12mm
[04] x 4
[01] x 1
[02] x 1 [03] x 1
M4 x 30mm
[05] x 4
M6 x 12mm
[06] x 4
M8 x 16mm
[09] x 4
[15] x 6 [16] x 6
⁄ in. x 2 ½ in.
[17] x 6
M6 x 20mm
[07] x 4
M6 x 35mm
[08] x 4
M8 x 40mm
[10] x 4
M4
[11] x 8
M4
[13] x 4
M6/M8
[12] x 4 M6/M8
[14] x 4
⁄ in. Hex Key
[18] x 1

6904-002015 <01>
4
1 Select TV Hardware and Mount TV Brackets
1-1 Choose screw length and diameter
1-2 Select the hardware conguration
Hand thread screws into the threaded inserts on the back of your
TV to determine the correct screw diameter (M4, M6, or M8).
Verify that there are adequate threads to secure the brackets to
the monitor. If you encounter resistance, stop immediately and
contact customer service.
CAUTION: Avoid potential personal injuries and property
damage! Use the shortest screw and spacer combination to
accomodate your needs. Using hardware that is too long may
damage your monitor’s internal components.
Your TV type will help you determine which hardware conguration to use. Match your type of TV to the suggested
hardware conguration on the next page.
A. Installation option without spacers (TVs with at backs).
B. Installation option using spacers (TVs with obstructed backs or inset mounting holes).
A B

6904-002015 <01> 5
1-3 Attach selected hardware
M4/M6/M8
M6/M8
M4
[04], [06],
[07], [09]
[11], [12]
[03]
[03]
[02]
[02]
[08], [10]
[13]
[14]
[11]
[11]
[12]
[05]
For TVs with an irregular back
Ensure the brackets is level on the back of the TV.
Standard congurations are shown. For special applications,
or if you are uncertain about your hardware selection, contact
Customer Service.
For TVs with a at back
Ensure the bracket is level on the back of the TV.
If you require additional space for cables, recesses, or
protrusions, see the conguration below.
[02], [03]
[02], [03]
[02], [03]

6904-002015 <01>
6
For ease of access, straps should be level with the bottom of the TV.
2 Adjust Strap
40.6 - 61 cm
(16 - 24 in.)
< 16 mm
(5/8 in.)
3 Wall Mounting - Wood Stud
3-1 Locate stud
3-2 Level wall plate [01] and mark hole locations
Verify the center of the stud using an awl, a thin nail, or an edge to edge stud
nder.
CAUTION: Avoid potential personal injuries and property damage!
Any material covering the wall must not exceed 16 mm (5/8 in.).
Minimum wood stud size: common 2 x 4 in (nominal 1.5 x 3.5 in).
[01]
5.5mm
(7/32 in.)
13mm
(1/2 in.)

6904-002015 <01> 7
3 Wall Mounting - Solid Concrete
and Concrete Block
3-1 Level wall plate [01] and mark hole locations
[16]
[17]
[01]
[01]
3-3 Drill pilot holes as illustrated
3-4Tighten lag bolts [17] only until the washers [16] are pulled rmly against the wall plate [01]
3Wall Mounting - Wood Stud - continued
CAUTION: Improper use could reduce the holding power of the lag
bolt. To avoid potential injuries or property damage: pilot holes MUST be
drilled to a depth of 75 mm (3 in.), using a 5.5 mm (7/32 in.) diameter drill
bit.
CAUTION: Improper use could reduce the holding power of the lag
bolt. To avoid potential injuries or property damage DO NOT over-tighten
the lag bolts [17].
75 mm
3 in.
CAUTION: Avoid potential personal injuries and property damage!
Mount the wall plate [01] directly onto the concrete surface.
Minimum solid concrete thickness: 8 in.
Minimum concrete block size: 8 x 8 x 16 in.
13 mm
(1/2 in.)
13 mm
(1/2 in.)

6904-002015 <01>
8
3-2 Drill pilot holes as illustrated
3-3 Insert anchors [15]
3-4Tighten lag bolts [17] only until the washers [16] are pulled rmly against the wall plate [01]
75 mm
(3 in.)
[15]
3 Wall Mounting - Solid Concrete and Concrete
Block - continued
CAUTION: To avoid potential injuries or property damage:
Pilot holes MUST be drilled to adepth of 75 mm (3 in.) using a 13 mm
(1/2 in.) diameter drill bit.
Never drill into the mortar between blocks.
CAUTION: To avoid potential injuries or property damage be sure
the anchors [15] seat ush with the concrete surface.
CAUTION: Improper use could reduce the holding power of the lag
bolt. To avoid potential injuries or property damage DO NOT over-tighten
the lag bolts [17].
[01]
[16]
[17]

6904-002015 <01> 9
4 Hang the TV with Mounting Brackets onto the Wall Plate
To remove the TV
HEAVY! You will need assistance with this step.
Pull down the straps (S) to disengage the locking tabs,
then lift the TV o the wall plate. Swing TV / bracket
assembly forward from the bottom and lift the TV from the
wall mount.
HEAVY! You will need assistance with this step.
Install the TV / Bracket assembly by tting the top hook
of the mounting bracket over the top edge of the wall
mount. Swing the mounting bracket down until the spring
loaded locking tabs (L) slip over and fully engages the
bottom edge of the wall mount.
CAUTION: Be sure the locking tabs (L) engage into
the locked position. There is an audible click when the
parts are correctly assembled.
(L)
(S)

6904-002015 <01>
10
Milestone AV Technologies and its aliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete.
However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible
contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or
obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or suciency of the information contained in this document.