SANWEI TTR007 User manual

TT.Robot
TTR007
发球机使用说明书
USER MANUAL

目 录
P2标准配件、技术参数
P3-P4安装步骤
P7故障处理
P9-P10配件更换
P5-P6功能介绍
P8注意事项
01
TTR007
P2 Accessories & Technical Specification
P3-P4 Installation
P5-P6 Functions
P7 Troubleshooting
P8 Precautions
P9-P10 Parts Replacement

标准配件
技术参数
02
A.
C.
D.
E.
F.
B.
TTR007
G.W.: 4.5KG
N.W.: 3.3KG
Packing Size: 40 x 38 x 37CM
Rated Voltage: 100-240V
Rated Power: 36W
Spin: Top Spin, Down Spin,
non-spin, Side spin
Serving Frequency: 40-70/Min
Serving Speed:3-30m/s
Maximum ball storage: 120 balls
Minimum ball storage: 10 balls
Serving Range: Covering whole table
Color: Black
毛重：4.5KG
净重：3.3KG
包装体积：长40*宽38*高37CM
额定电压：100-240V
额定功率：36W
出球旋转：上旋转、下旋转、
不旋转、左右侧旋球
出球频率：40-70/分钟
出球速度：3-30m/s
最大储球量：120个
最少储球量：10个
出球落点：全台不定点
颜色：黑色■
Providing 9 Spins + Non-Spin solutions
Pitch angle is adjustable
Left and right angle is adjustable randomly
可发9种旋转球+1种不旋转球
可上下调整出球角度
可随机调整左右角度
A.主机
B.机头
C.储球筒
D.电源
A. Main Body
B.Robot head
C.Ball storage barrel
D.Power Supply
E.固定架
F.侧球尺
E.Frame
F.Measuring tool
Technical Specification Accessories

安装步骤
03
TTR007
①打开包装，检查配件。
①Unpack and then check
the accessories.
②将机头连接主机，然后用固定盖
固定，扭上螺丝。
④将储球筒安装到主机的卡位上，
旋转固定即可。
⑤取出固定架，安装到标准
球台上，然后将发球机固定
在铁架上
⑥最后将电源插上控制器的
电源插孔。
⑥Finally, plug the power
supply in
⑤Take out the frame and
install to standard table,
then fix robot on the
frame.
④Fix the ball storage barrel to
the main body and rotate it to
fix.
③USB连接线插入主机接口处。
③Connect the USB cable to the
main body.
②Connect the robot head to the
main body.

安装步骤
04
开关和出球频率调整
摆动频率调整
上旋转速调整
下旋转速调整
控制上旋轮转速
控制下旋轮转速
TTR007
A. Switch, and serving frequency
B. Swing frequency
C. Top spin speed
D. Down spin speed
A. 开关和出球频率调整
B. 摆动频率调整
C. 上旋转速调整
D. 下旋转速调整
A. 调节越大，出球频率越快。
B. 调节越大，机头的摆头
频率越快。
C. 调节越大，上旋轮转速
越快。
D. 调节越大，下旋轮转速
越快。
D. Turn it up, down spin
can get stronger
C. Turn it up, top spin can
get stronger
B. Wider the balls can cover
while turning it up
A. Serving frequency is higher
while turning this up

功能介绍
05
0
1
小提示：
发球落点变化范围示意图
摆动范围
TTR007
Serve location range diagram
Swing range
Functions
Tips:
When the Swing Frequency is set to 0, Robot will serve to fixed location.
When the Swing Frequency is set to 1, Robot will serve to all possible locations on
the table.
Controlle

功能介绍
水平线 水平线
上轮
下轮
机头旋转范围
9
180
1
2
3
1 2 1 3
铜旋钮
必须松开铜旋钮才能调整机头高低
当机头正在摇摆时不要调整
发球跳动示意图
06
TTR007
Copper knob
Serve directly (1 jump)
Serve indirectly (2 jumps)
Serving type: Directly (1 jump) and indirectly (2 jumps)
Indirectly type: with a proper speed and spin, it is much more suitable for beginner to
practice different skills of serving and returning ball.
Direct type: compared with indirect type, it is stronger on its speed and spin.
With a proper speed and spin, it can serve loop, attack and high ball. Suitable for daily
training.
Loosen the copper knob first, before
adjusting the elevation of robot head.
DO NOT adjust the knob while the head is
working.
Top-Wheel
horizontal linehorizontal line
Robot head swing range
Functions
Robot can serve 9 kinds of spin ball and a non-spin.
The head can swing within 180 degree.
1 Position: The rotation of top-wheel is top spin, of the
bottom-wheel is down spin. With the same position is
the non-spin.
2 Position: The rotation of top-wheel is left spin, of the
bottom-wheel is right spin. With the same position is
the non-spin.
3 Position: The rotation of top-wheel is right spin, of
the bottom-wheel is left spin. With the same position
is the non-spin.
Adjust two wheels and speed between 1 and 2 or
among 1 to 3, can combine different kinds of spins.

07
故障 现象 故障 原因 处理办法
打开电源机器无反应
不出球
发球无力
不摆头
摆头幅度小
开始开关没反应/频率速度开关不可调
更换电源
插好连线
拆卸机头，清理球道和球
换成标准40mm新球
更换
更换
更换
重插
重插
更换
更换
重插
重插
重新设置调整杆
更换
电源故障
连线没有插好
球道脏
球有伤或球脏、球不标准
供球电机损坏
供球变速箱坏齿轮坏
发球电机坏
插座接触不良
发球电机连线断线
摆头电机损坏
摆头齿轮箱变速齿轮损坏
插座接触不良
摆头电机连线断线
调整杆设置错误
控制盒坏
故障处理
TTR007
Fault phenomenon Failure cause Solutions
Power and no reaction
Balls are not serving out
Serving ball weakly
Not Swinging
Swing range is narrower
Start and speed button no reaction
Adjusting rod is error
Controller is broken
Reset
Replace
Ball groove is dirty
Balls are broken, dirty or not standard
Serving Motor is down
Gearbox is broken
Serving Motor is down
Connection of power socket is poor
Line of motor is disconnected
Swing Motor is down
Swing Gearbox is broken
Connection of power socket is poor
Line of the motor is disconnected
Power failure
Connection is not good
Replace power supply
Replug power cord
Take down the robot head, and then clean the ball groove and balls
Change to standard 40+ balls
Replace
Replace
Replace
Replug
Replug
Replace
Replace
Replug
Replug
Troubleshooting

08
注意事项
1. 儿童必须在成年人或者父母的监护和指导下正确使用发球机。
2. 请使用标准 40MM 或40+乒乓球，可选用三维品牌训练球或一星以上球。请勿使用太软或者
不规则乒乓球，避免造成发球机卡球。
3. 新乒乓球使用前，请用清水或者清洁剂搓洗干净，晾干后再使用。并定期清洗乒乓球和发球机球道，
保持整洁，减少故障发生。
4.请在发球机静止情况下，往储球筒里加入乒乓球，避免卡球。
5. 在长时间不使用发球机时，请清理干净，用袋子包装好储放。
6. 如在操作中遇到任何问题，可联系致电我们售后服务。
TTR007
1. Children must use the robot correctly under directions of adults or parents.
2. Please use the standard 40+ balls. Better performance with SANWEI® ABS 1 Star Ball or others better than 1 star ball.
Please don’t use the balls that are too soft or irregular to avoid any clamping.
3. Please clean the new balls with clear water or cleaning agent and dry them before you use them. And clean the balls and the
ball groove termly to keep the machine clean and reduce the failure.
4. Please add the balls to the storage tube when the machine is off to avoid clamping balls.
5. If you don't use the robot for a long time, please clean it up and with good storage bags.
6. If you have any problems, please contact our after-sale service.
Precautions
Attentions:

09
更换配件
TTR007
请在干净的环境下使用发球机，
定时清理发球机灰尘和清洗乒乓球。
如果在使用TT.Robot发球机时，经过一系列故障排除后，
发球轮不转动，无法发送球，请更换发球机；如在使用一
段时间，发现发球轮损坏和变形，请更换发球轮。
①.请检查和确定损坏是上轮发球轮
还是下轮发球轮
②.拆卸机头侧面4个螺丝
①.Check which driving wheel
is damaged
②.Disassemble 4 screws from
side board
③.然后卸下固定发球轮的螺丝，
取出损坏的发球轮。
④.取出一个新的发球轮进行更换，
按照原先拆卸步骤安装回去。
③.Disassemble the screw
from driving wheel, take out
the damaged wheel
④.Take a new wheel, and put it
inside follow the process before
Parts Replacement
Please use robot in clean environment, clean
the dust and wash the balls regularly.
Down serving motor
In the case the driving wheels are not working and not deliver balls, after trouble-
shooting, might you need to change the motor. In the case that the driving wheel is
damaged or out of shape, you might need to change the driving wheels.
A. Change the serving wheel

10
更换配件
.更换发球电机
④取出电机，剪断连接电机上的
两条正负极电线。
⑤用火机或者剪刀将正
负极电线一小节去皮，
准备好更换的电机，
红色电线对准电机正
极处穿上扭紧，黑色
电线穿过电机的负极
处扭紧。
注：电机上有个小圆
圈，上有个“+”为正
极。
⑥为避免在使用过程中，
正负极电线相互碰撞，
请用胶布密封露出铜
芯的其中一边正负极
电线处。
⑦按照拆卸时的步骤安装回去，即可继续使用。
①先检测出上下电机哪个损坏，
确定之后，需要先拆卸出与之
相对应的上发球轮或者下发球轮。
②取出发球轮后，用螺丝刀拆卸固
定发球轮的2个螺丝。
③然后再用螺丝刀卸下耳盖上的
螺丝，即可取出需要更换的发
球电机。
TTR007
Parts Replacement
A. Change serving moto
1. Find out which motor is damaged.
Disassemble the ball wheel first
2. After taking out the wheel,
disassemble 2 screws.
3. Then disassemble screws of motor
cover, and take out the damaged motor
4. Cut the positive and negative line.
5. Prepare a new motor, connect the red
wire with the positive pole of motor,
and the black wire with its negative pole.
6. Sealing with insulating tape of the
bare wire to avoid the red and black wire
touching each other
PS: The little circle with a “+” symbol is
indicating the positive pole
7. Put it inside follow the process before