Sanyo PLC-XP41 User manual

FILE NO.
Notice
CORRECTION ●PRODUCTION CHANGE
SERVICE FLASH ADD INFORMATION
REVISION-5
Please add this notice to the Service Manual listed below.
Category : Multi-media Projector Issued Date : June / 2004
PLC-XP41 MB8-XP4101
Model : PLC-XP41L Effective from : Chassis No. MB8-XP41L01
Canada, U.S./Europe,
Destination : Asia, Africa,U.K REF. NO. : SM5110329
NOTE: Match the Chassis No. on the unit’s back cover with the Chassis No. in the Service
Manual.
If the Chassis. No. does not match the unit’s, additional service literature is required.
Only the difference service information is given in this manual. For detailed service infor-
mation, refer to the original service manual SM5110329, issued in April 2002, for
Models PLC-XP41/41L.
PRODUCT CODE
PLC-XP41 PLC-XP41L
1 122 110 30 (MB8AB) 1 122 110 90 (MB8AP)
1 122 111 30 (PB8AB) REFERENCE NO. SM5110329-05
FILE WITH ORIGINAL SERVICE MANUAL (SM5110329)
Differences:
Outline
PLC-XP41,PLC-XP41L Power and Sub Power Board were changed.

-2-
■Specifications
●The specifications are subject to change without notice.
This symbol on the nameplate means the product is Listed by Underwriters
Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety stan-
dards against risk of fire, casualty and electrical hazards.
Projector Type Multi-media Projector
Dimensions (W x H x D) 12.6” x 6.6” x 16.8” (319mm x 168mm x 429.5mm) (PLC-XP41/X41L)
Net Weight 17.4 lbs (7.9 kg) (PLC-XP41),
15.7 lbs (7.1 kg) (PLC-X41L)
LCD Panel System 1.3” TFT Active Matrix type, 3 panels
Panel Resolution 1024 x 768 dots
Number of Pixels 2,359,296 (1024 x 768 x 3 panels)
Color System 6 color system (PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N)
High Definition TV SIgnals 480i, 480p, 575i, 575p, 720p. 1035i and 1080i
Scanning Frequency H-sync. 15 ~ 100kHz, V-sync. 50 ~ 100Hz
Projection Image Size (diagonal) Adjustable from 31” to 400”
Horizontal Resolution 800 TV lines (HDTV)
Projection Lens F 1.8 ~2.1 lens with f=48.4mm ~ 62.8mm with motor zoom and focus (PLC-XP41)
Throw Distance 4.6’ ~ 47.3’ (1.4m ~ 14.4m) (PLC-XP41)
Motorized Lens Shift Up and Down
Projection Lamp 275watts
Input 1 Jacks DVI Terminal (Digital), HDB 15-pin Terminal (Analog) and Stereo Mini Type
Jack (Audio)
Input 2 Jacks BNC Type x 5 (G or VIDEO/Y, B or Cb/Pb, R or Cr/Pr, H and V), Stereo
Mini Type Jack (Audio)
Input 3 Jacks RCA Type x 3 (VIDEO/Y, Cb/Pb, Cr/Pr), RCA Type x 2 (Audio R and L) and
DIN 4-pin (S-Video)
Other Jacks DIN 8-pin (Control port), USB port (Series B receptacle), Wired Remote
Jack and Network Board Connector Jack
Built-in Speakers 2 speakers Stereo (R and L), 2 watts RMS (T.H.D. 10%)
Feet Adjustment 0˚ to 10.5˚
Voltage and AC 100 ~ 120V (4.8A Max. Ampere), 50/60Hz (The U.S.A and Canada)
Power Consumption AC 200 ~ 240V (2.4A Max. Ampere), 50/60Hz (Continental Europe)
Operating Temperature 41 ˚F ~ 95 ˚F (5˚C ~ 35˚C)
Storage Temperature 14 ˚F ~ 140 ˚F (-10˚C ~ 60˚C)
Remote Control Transmitters Wireless/Wired Remote Control, batteries AA, UM3 or R06 Type x 2

-3-
■Adjustments after Parts Replacement
Condenser lens adjustment ❍●
Relay lens adjustment ❍●
Contrast Adjustment
R-Contrast adjustment ●
G-Contrast adjustment ●
B-Contrast adjustment ●
Output voltage adjustment ●
+16 V adjustment ●
Video center adjustment ●
NRS adjustment ●
PC pedestal adjustment ●
Black level adjustment ●
PC gain adjustment ●
PC gamma shift adjustment ●
HDTV pedestal adjustment ●
HDTV A/D input adjustment ●
HDTV Gain adjustment ●
Video pedestal adjustment ●
Video A/D input adjustment ●
A/D offset adjustment ●
Video gain adjustment ●
Video gamma shift adjustment ●
Common center adjustment ● ●
White balance adjustment ❍ ❍
Disassembly / Replaced Parts
LCD/
Prism
Ass’y
Condenser
Lens
Polarized glass
RGB
Optical Adjustments
Electrical Adjustments
● :Adjustment necessary ❍ :Check necessary
Sub Power
Board Main Board
Relay
Lens
Power
Board

-4-
■Electrical Adjustments
To enter the service mode
To enter the “Service Mode”, press and hold the MENU and IMAGE button on the projector at the same time for
more than 3 seconds. The service menu appears on the screen as follows.
To adjust service data
Select the adjustment group no. by pressing the MENU (+) or IMAGE (-) button, and select the adjustment item
no. by pressing the pointer UP or DOWN button, and change the data value by pressing the VOLUME – or VOL-
UME + button.Refer to the “Service Adjustment Data Table” for further description of adjustment group no., item
no. and data value.
To exit the service mode
To exit the service mode, press the POWER ON-OFF button on the projector or remote control unit.
●Service Adjustment Menu Operation
Service Mode
Input 1
Group No. Data
0032
Ver. 1.00 .00
IC808 on the main board stores the data for the serv-
ice adjustments, and should not be replaced except for
the case of defective device.
If replaced, it should be performed the re-adjustments
following to the “Electrical Adjustments”.
The data of lamp replacement monitor timer is stored
in the IC808.
Please note that the lamp replace counter is reset
when the memory IC (IC808) is replaced.
(Lamp replace counter can not be set to the previous
value.)
● Caution to memory IC replacement
When IC808 is replaced with new one, the CPU writes
down the default data of the service adjustments to the
replaced IC, refer to the service adjustment table. As
these data are not the same data as factory shipped
data, it should be required to perform the re-adjust-
ments following to the “Electrical Adjustments”.
Please note that the lamp replace counter is reset.
● Caution of Main Board replacement (in the case
IC808 is not defective)
When the main board is replaced, IC808 should be
replaced with the one on previous main board. After
replacement, it should be required to perform the re-
adjustments following to the “Electrical Adjustments”.
In this case, the lamp replace counter can be kept the
value as before.
● Memory IC Replacement
Group No. Data value
Item No.

-5-
Electrical Adjustments
[Adjustment Condition]
●Input signal
Video signal .......................... 1.0Vp-p/75Ωterminated, 16 steps gray
scale (Composite video signal)
Computer signal .................... 0.7Vp-p/75Ωterminated, 16 steps gray
scale pattern (XGA)
Component Video signal ...... 0.7Vp-p/75Ωterminated, 16 steps gray
scale (Component video signal with
480p or 1080i format)
●Picture control mode .............. “STANDARD” mode unless otherwise
noted.
Note:
* Please refer to “Service Adjustment Menu Operation” for entering to the service mode and adjusting the service
data.
White 100% Black 100%
After replacing the Power Board readjust the Output
voltage adjustment as follows.
1. Connect a digital voltmeter to pin 1 (+) of K6A and
chassis ground (-).
2. Adjust the voltage by using VR601 on the power
board as following.
AC Input Reading
230V 370 ±2Vdc
or 120V 340 ±2Vdc
Caution:
Be sure to connect the lamp when taking this adjust-
ment.
●Circuit Adjustments
CAUTION: The each circuit has been made by the fine adjustment at factory. Do not attempt to adjust the follow-
ing adjustments except requiring the readjustments in servicing otherwise it may cause loss of per-
formance and product safety.
Output Voltage adjustment
1. Receive the 16-step gray scale video signal with
Input 3 [VIDEO] mode.
2. Connect a digital voltmeter to pin 3 (+) of CN6A and
chassis ground (-).
3. Adjust the voltage to be 15.8 ±0.1Vdc by using
VR681 on the power board.
+16V adjustment
1. Receive the 16-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Connect a digital voltmeter to test point “TP531”(+)
and chassis ground (-).
4. Select group no. “5”, item no. “1”and change data
value to adjust the voltage to be 7.50 ±0.1Vdc.
5. Connect a digital voltmeter to test point “TP501”(+)
and chassis ground (-).
6. Select item no. “0”and change data value to adjust
the voltage to be 7.50 ±0.1Vdc.
7. Connect a digital voltmeter to test point “TP561”(+)
and chassis ground (-).
8. Select item no. “2”and change data value to adjust
the voltage to be 7.50 ±0.1Vdc.
Video Center adjustment
16 steps gray scale pattern
Note:
The above adjustments are carried out at the spare
parts shipment, therefore it is not required when replac-
ing the power board.

-6-
Electrical Adjustments
1. Receive the 16-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP531”(+) and
chassis ground (-).
4. Select group no. “5”, item no. “16”and change data
value to adjust the pedestal level and black level to be
the same level.
5. Connect an oscilloscope to test point “TP501”(+) and
chassis ground (-).
6. Select item no. “15”and change data value to adjust
the pedestal level and black level to be the same
level.
7. Connect an oscilloscope to test point “TP561”(+) and
chassis ground (-).
8. Select item no. “17”and change data value to adjust
the pedestal level and black level to be the same
level.
Pedestal Lebel = Black Lebel
PC Pedestal adjustment
1. Receive the a6-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP3671”(+)
and chassis ground (-).
4. Select group no. “5”, item no. “6”and change data
value to adjust amplitude “a” to be 2.0 ±0.1V.
5. Select item no. “7”and change data value to adjust
amplitude “b” to be 6.5 ±0.1V.
(a)
(b)
GND
NRS adjustment
1. Receive the 16-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP531”(+)
and chassis ground (-).
4. Select group no. “5”, item no. “4”and change data
value to adjust amplitude “a” to be 10.0 ±0.1V.
5. Connect an oscilloscope to test point “TP501”(+)
and chassis ground (-).
6. Select item no. “3”and change data value to adjust
amplitude “a” to be 10.0 ±0.1V.
7. Connect an oscilloscope to test point “TP561”(+)
and chassis ground (-).
8. Select item no. “5”and change data value to adjust
amplitude “a” to be 10.0 ±0.1V.
(a)
black level
black level
Black Level adjustment
1. Receive the 16-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP531”(+)
and chassis ground (-).
4. Select group no. “4”, item no. “4”and set data value
to “600”, and then decrease data to adjust waveform
“a” to be minimum amplitude.
5. Connect an oscilloscope to test point “TP501”(+)
and chassis ground (-).
6. Select item no. “5”and set data value to “600”, and
then decrease data to adjust waveform “a” to be mini-
mum amplitude.
7. Connect an oscilloscope to test point “TP561”(+)
and chassis ground (-).
8. Select item no. “3”and set data value to “580”, and
then decrease data to adjust waveform “a” to be mini-
mum amplitude.
White Level
(a)
PC Gain adjustment

-7-
Electrical Adjustments
1. Receive the 16-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Select group no. “4”, item no. “6”and change data
value to reproduce the proper gray scale picture on
the screen.
PC Gamma Shift adjustment
[480p-PEDESTAL ADJUSTMENT]
1. Receive the 16-step gray scale component signal
[480p] with Input 3 [COMPONENT] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP21G”(+)
and chassis ground (-).
4. Select group no. “3”, item no. “1”and change data
value to adjust the pedestal level and black level to be
the same level.
5. Connect an oscilloscope to test point “TP21B”(+)
and chassis ground (-).
6. Select group no. “5”, item no. “14”and change data
value to adjust the pedestal level and black level to be
the same level.
7. Connect an oscilloscope to test point “TP21R”(+)
and chassis ground (-).
8. Select item no. “13 and change data value to adjust
the pedestal level and black level to be the same
level.
[1080i-PEDESTAL ADJUSTMENT]
1. Receive the 16-step gray scale component signal
[1080i] with Input 3 [COMPONENT] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP21G”(+)
and chassis ground (-).
4. Select group no. “3”, item no. “1”and change data
value to adjust the pedestal level and black level to be
the same level.
5. Connect an oscilloscope to test point “TP21B”(+)
and chassis ground (-).
6. Select group no. “5”, item no. “14”and change data
value to adjust the pedestal level and black level to be
the same level.
7. Connect an oscilloscope to test point “TP21R”(+)
and chassis ground (-).
Pedestal Lebel = Black Lebel
HDTV Pedestal adjustment
8. Select item no. “13 and change data value to adjust
the pedestal level and black level to be the same
level.
[480p-A/D INPUT ADJUSTMENT]
1. Receive the 16-step gray scale component signal
[480p] with Input 3 [COMPONENT] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP21G”(+)
and chassis ground (-).
4. Select group no. “3”, item no. “0”and change data
value to adjust amplitude “a” to be 0.9 ±0.1V.
5. Connect an oscilloscope to test point “TP21B”(+)
and chassis ground (-).
6. Select item no. “4”and change data value to adjust
amplitude “a” to be 0.9 ±0.1V.
7. Connect an oscilloscope to test point “TP21R”(+)
and chassis ground (-).
8. Select item no. “2and change data value to adjust
amplitude “a” to be 0.9 ±0.1V.
[1080i-A/D INPUT ADJUSTMENT]
1. Receive the 16-step gray scale component signal
[1080i] with Input 3 [COMPONENT] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP21G”(+)
and chassis ground (-).
4. Select group no. “3”, item no. “0”and change data
value to adjust amplitude “a” to be 0.9 ±0.1V.
5. Connect an oscilloscope to test point “TP21B”(+)
and chassis ground (-).
6. Select item no. “4”and change data value to adjust
amplitude “a” to be 0.9 ±0.1V.
7. Connect an oscilloscope to test point “TP21R”(+)
and chassis ground (-).
8. Select item no. “2and change data value to adjust
amplitude “a” to be 0.9 ±0.1V.
Note: This adjustment should be done after HDTV
Pedestal adjustment.
(a)
(a)
HDTV A/D Input adjustment

-8-
Electrical Adjustments
1. Receive the 16-step gray scale component signal
[1080i] with Input 3 [COMPONENT] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP531”(+)
and chassis ground (-).
4. Select group no. “4”, item no. “4”and set data value
to “600”, and then decrease data to adjust waveform
“a” to be minimum amplitude.
5. Connect an oscilloscope to test point “TP501”(+)
and chassis ground (-).
6. Select item no. “5”and set data value to “600”, and
then decrease data to adjust waveform “a” to be mini-
mum amplitude.
7. Connect an oscilloscope to test point “TP561”(+)
and chassis ground (-).
8. Select item no. “3”and set data value to “600”, and
then decrease data to adjust waveform “a” to be mini-
mum amplitude.
White Level
(a)
HDTV Gain adjustment
1. Receive the 16-step gray scale video signal with
Input 3 [VIDEO] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP4151G”(+)
and chassis ground (-).
4. Select group no. “3”, item no. “1”and change data
value to adjust the pedestal level and black level to be
the same level.
5. Connect an oscilloscope to test point “TP4151B”(+)
and chassis ground (-).
6. Select group no. “5”, item no. “14”and change data
value to adjust the pedestal level and black level to be
the same level.
7. Connect an oscilloscope to test point “TP4151R”(+)
and chassis ground (-).
8. Select item no. “13 and change data value to adjust
the pedestal level and black level to be the same
level.
Pedestal Lebel = Black Lebel
VIDEO Pedestal adjustment
1. Receive the 16-step gray scale video signal with
Input 3 [VIDEO] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP4151G”(+)
and chassis ground (-).
4. Select group no. “3”, item no. “0”and change data
value to adjust amplitude “a” to be 0.8 ±0.1V.
5. Connect an oscilloscope to test point “TP4151B”(+)
and chassis ground (-).
6. Select item no. “4”and change data value to adjust
amplitude “a” to be 0.8 ±0.1V.
7. Connect an oscilloscope to test point “TP4151R”(+)
and chassis ground (-).
8. Select item no. “2and change data value to adjust
amplitude “a” to be 0.8 ±0.1V.
Note: This adjustment should be done after VIDEO
Pedestal adjustment.
(a)
VIDEO A/D Input adjustment

-9-
Electrical Adjustments
1. Receive the 16-step gray scale video signal with
Input 3 [VIDEO] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP531”(+) and
chassis ground (-).
4. Select group no. “6”, item no. “11”and change data
value to adjust the pedestal level and black level to be
the same level.
5. Connect an oscilloscope to test point “TP501”(+) and
chassis ground (-).
6. Select item no. “12”and change data value to adjust
the pedestal level and black level to be the same
level.
7. Connect an oscilloscope to test point “TP561”(+) and
chassis ground (-).
8. Select item no. “10 and change data value to adjust
the pedestal level and black level to be the same
level.
Pedestal Lebel = Black Lebel
1. Receive the 16-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Project only green light component to the screen.
4. Select group no. “5”, item no. “11”and change data
value to obtain the minimum flicker on the screen.
5. Project only blue light component to the screen.
6. Select item no. “12”and change data value to obtain
the minimum flicker on the screen.
7. Project only red light component to the screen.
8. Select item no. “10”and change data value to obtain
the minimum flicker on the screen.
A/D Offset adjustment
Common Center adjustment
[PC WHITE BALANCE ADJUSTMENT]
1. Receive the 16-step gray scale computer signal with
Input 1 [COMPUTER] mode.
2. Enter the service mode.
3. Select group no. “4”, item no. “7”(Red) or “8”(Blue),
and change data values respectively to make a prop-
er white balance.
[AV WHITE BALANCE ADJUSTMENT]
4. Receive the 16-step gray scale video signal with
Input 3 [VIDEO] mode.
5. Enter the service mode.
6. Select group no. “4”, item no. “7”(Red) or “8”(Blue),
and change data values respectively to make a prop-
er white balance.
Confirm that the same white balance is obtained in
video and computer input.
White Balance adjustment
If you find the color shading on the screen, please
adjust the white uniformity by using the proper comput-
er and “Color Shading Correction” software supplied
separately. The software can be ordered as follows;
COLOR SHADING CORRECTION SOFTWARE
Service Parts No.645 051 2308
NOTE ON WHITE UNIFORMITY
ADJUSTMENT
1. Receive the 16-step gray scale video signal with Input
3 [VIDEO] mode.
2. Enter the service mode.
3. Connect an oscilloscope to test point “TP531”(+)
and chassis ground (-).
4. Select group no. “4”, item no. “4”and set data value
to “600”, and then decrease data to adjust waveform
“a” to be minimum amplitude.
5. Connect an oscilloscope to test point “TP501”(+)
and chassis ground (-).
6. Select item no. “5”and set data value to “600”, and
then decrease data to adjust waveform “a” to be mini-
mum amplitude.
7. Connect an oscilloscope to test point “TP561”(+)
and chassis ground (-).
8. Select item no. “3”and set data value to “580”, and
then decrease data to adjust waveform “a” to be mini-
mum amplitude.
White Level
(a)
Video Gain adjustment
1. Receive the 16-step gray scale video signal with
Input 3 [VIDEO] mode.
2. Enter the service mode.
3. Select group no. “4”, item no. “6”and change data
value to reproduce the proper gray scale picture on
the screen.
Video Gamma Shift adjustment

-10-
Group: 0 TC90A26
0Y-EQ_GAIN 3 0 ~ 3
1Y-EQ_N_C_LIM 3 0 ~ 3
2V-ENH_GAIN 4 0 ~ 7
3V_ENH_CORING 2 0 ~ 3
4NTSC443_SW 1 0 ~ 1 Input signal setting 0:NTSC4.43 1:PAL60 (Only effective for NTSC4.43 signal inputs)
Group: 1 uPD64082
0NRMD 0 0 ~ 3
1HDP 4 0 ~ 7
2CDL 4 0 ~ 7
3DYCOR 4 0 ~ 15
4DYGAIN 15 0 ~ 15
5DCCOR 2 0 ~ 15
6DCGAIN 13 0 ~ 15
7YNRK 0 0 or 1
8YNRINV 0 0 or 1
9YNRLIM 0 0 ~ 3
10 CNRK 0 0 or 1
11 CNRINV 0 0 or 1
12 CNRLIM 0 0 ~ 3
13 VAPGAIN 2 0 ~ 15
14 VAPINV 2 0 ~ 15
15 YPFT 3 0 ~ 3
16 YPFG 9 0 ~ 15
17 V1PSEL 3 0 ~ 3
18 VEGSEL 3 0 ~ 3
19 CC3N 0 0 or 1
20 SELD2FH 1 0 or 1
21 SELDFL 1 0 or 1
22 YHCOR 1 0 ~ 3
23 HPLLFS 1 0 or 1
24 PLLFG 1 0 or 1
25 KILR 3 0 ~ 15
26 HSSL 12 0 ~ 15
27 VSSL 3 0 ~ 15
28 BGPS 7 0 ~ 15
29 BGPW 3 0 ~ 15
Group: 2 TB1274
0TINT 32 0 ~ 63
1SHP_EQ 2 0 ~ 3
2SHP_FO 2 0 ~ 3
3SHP_GAIN 8/8/8/8/8/8/8 0 ~ 15 VideoNT/ PAL,PALM,PALN/SECAM,BW60,BW50/ NT443/ PAL60/ S-Video/YCbCr
4Y_OUT_LEVEL 31/32/32/32/32 0 ~ 63 VideoNT/ NT443/ PAL,PALM,PALN/ PAL60/ SECAM,BW
0.7V 32/32/32/32/32/32 S-VideoNT,BW/ NT443/ PAL,PALM,PALN/ PAL60/ SECAM/ YCbCr
5C_OUT_LEVEL 12/12/15/15/22 0 ~ 63 VideoNT/ NT443/ PAL,PALM,PALN/ PAL60/ SECAM,BW
0.6V 12/12/15/15/22/18/20 S-VideoNT,BW/ NT443/ PAL,PALM,PALN/ PAL60/ SECAM/480i/575i
6Y_DELAY 5/5/4/4/4 0 ~ 15 Video NT,BW60/ PAL,PALM,PALN,BW50/ SECAM/NT443/PAL60
4/4/3/3/4 S-Video NT,BW60/PAL,PALM,PALN,BW50/ SECAM/ NT443/ PAL60
7COL_SYS - -
8X’TAL - -
9NOISE_DET - - Read Only
10 V_FREQ - -
11 Vert. Std - -
12 CID - -
13 VSIG - -
14 MVM 0 0 or 1
15 AFC_GAIN 1 0 ~ 3
16 SECAM_GP 7 0 ~ 7
Group: 3 CXA2101
0PICTURE 15/25/25 0 ~ 63 NT,PAL,SECAM,NT443,PALM,PALN,480i,575i/ 480p,575p/ 1080i,1035i,720p ✻A/D input Adj.[G]
1BRIGHT 50/50/50 0 ~ 63 NT,PAL,SECAM,NT443,PALM,PALN,480i,575i/ 480p,575p/ 1080i,1035i,720p ✻Pedestal Adj.[G]
2R_DRIVE 31/31/31 0 ~ 63 NT,NT443,PAL,PALM,PALN,480i,575i/ 480p,575p/ 1080i,1035i,720p ✻A/D input Adj.[R]
3G_DRIVE 31 0 ~ 63
No. Adjustment Item Initial Value Range Input source / Description
Electrical Adjustments
●Service Adjustment Data Table These initial values are the reference data written from the CPU
ROM to memory IC when replaced new memory IC. The adjust-
ment items indicated with “✻”are required to readjust following
to the “Electrical adjustments”. Other items should be used with
the initial data value.

-11-
4B_DRIVE 31/31/31 0 ~ 63 NT,NT443,PAL,PALM,PALN,480i,575i/ 480p,575p/ 1080i,1035i,720p ✻A/D input Adj.[B]
5HSEP_SEL 1 0 ~ 1
6CR_OFFSET1 7 0 ~ 15
7CB_OFFSET1 7 0 ~ 15
8BLK_BOTTOM 15 0 ~ 15
9R-Y/R 12/13/6/6 0 ~ 15 NT,NT443,480i,480p/PAL,PALM,PALN,PAL60,SECAM,575i,575p/1035i/1080i,720p
10 R-Y/B 12/15/5/5 0 ~ 15
11 G-Y/R 12/12/8/8 0 ~ 15
12 G-Y/B 5/4/10/10 0 ~ 15
13 MAT_OUT 0/0/0/1 0 ~ 3
14 SYSTEM 0/1/2/2 0 ~ 3 NT,NT443,PAL,PALM,PALN,SECAM,480i,575i/ 480p,575p/ 1080i60,1035i,720p/1080i50
15 V_TC 2/1/1/0 0 ~ 3
16 H_WIDTH 2/1/1/0 0 ~ 3
17 HD_TC 1/1/0/0 0 ~ 3
18 HS_MASK 0/1/1/1 0 ~ 1
19 CTI_LEVEL 1/1/1/0/0 0 ~ 3 NT,NT443,PAL,PALM,PALN,SECAM/ 480i,575i/ 480p,575p/ 1080i60,1035i,720p/ 1080i50
20 SUB_SHP 2/2/1/1 0 ~ 3 NT,NT443,PAL,SECAM,PALM,PALN,480i,575i/ 480p,575p/ 1080i60,1035i,720p/ 1080i50
21 SHP_FO 3/3/3/3 0 ~ 3
22 PRE_OVER 2/3/0/0 0 ~ 3
23 LTI_LEVEL 1/1/0/0 0 ~ 3 NT,NT443,PAL,SECAM,PALM,PALN,480i,575i/ 480p,575p / 1080i60,1035i,720p/ 1080i50
24 D_PIC 0/0/1/1 0 ~ 3 NT,NT443,PAL,SECAM,PALM,PALN,480i,575i/ 480p,575p / 1080i60,1035i,720p/ 1080i50”
25 HUE 31/31 0 ~ 63 PAL,PALM,PALN,PAL60,SECAM/ 575i,575p adjutable only those mode.
26 SUB_COL 7/7/7/8/3/3 0 ~ 15 NT,NT443/PAL,PALM,PALN,PAL60,SECAM/480i,480p/575i,575p/1035i/1080i,720p
27 SUB_HUE 7/7/8/7/9/6 0 ~ 15 NT,NT443/PAL,PALM,PALN,PAL60,SECAM/480i,480p/575i,575p/1035i/1080i,720p
28 CINEMA CTI_LEVEL 0
29 CINEMA LTI_LEVEL 0
Group: 4 L3E07050
0B_SUB_BRT 0/0 0 ~ 1023 PC/DVI,AV
1G_SUB_BRT 0/0 0 ~ 1023
2R_SUB_BRT 0/0 0 ~ 1023
3R_SUB_GAIN 367/390/300/420 0 ~ 1023 PC/AV/DVI/HD ✻Gain Adj.[R]
4G_SUB_GAIN 367/390/300/420 0 ~ 1023 ✻Gain Adj.[G]
5B_SUB_GAIN 367/390/300/420 0 ~ 1023 ✻Gain Adj.[B]
6Standard G GAMMA SHIFT 350/390 0 ~ 1023 PC,DVI std/AV Std Center value 512 * Modify RGB data at the sane time when changing G data. ✻
7Standard R GAMMA SHIFT 350/390 0 ~ 1023 PC,DVI std/AV Std Center value 512 ✻White balance Adj.[R] Gamma Shift Adj.
8Standard B GAMMA SHIFT 350/390 0 ~ 1023 PC,DVI std/AV Std Center value 512 ✻White Balance Adj.[B]
9Standard GAMMA 0 0/0 0 ~ 1023 PC,DVI Standard / AV Standard
10 Standard GAMMA 1 160/145 0 ~ 1023 Read only
11 Standard GAMMA 2 274/263 0 ~ 1023
12 Standard GAMMA 3 386/377 0 ~ 1023
13 Standard GAMMA 4 477/471 0 ~ 1023
14 Standard GAMMA 5 544/537 0 ~ 1023
15 Standard GAMMA 6 611/604 0 ~ 1023
16 Standard GAMMA 7 659/648 0 ~ 1023
17 Standard GAMMA 8 700/684 0 ~ 1023
18 Standard GAMMA 9 736/709 0 ~ 1023
19 Standard GAMMA 10 770/737 0 ~ 1023
20 Standard GAMMA 11 802/766 0 ~ 1023
21 Standard GAMMA 12 840/804 0 ~ 1023
22 Standard GAMMA 13 874/837 0 ~ 1023
23 Standard GAMMA 14 926/902 0 ~ 1023
24 Standard GAMMA 15 1023/1023 0 ~ 1023
25 Real/Cinema G GAMMA SHIFT 506/506 385 ~ 639 PC,DVI Real / AV Cinema
26 Real/Cinema R GAMMA SHIFT 512/512 385 ~ 639
27 Real/Cinema B GAMMA SHIFT 502/502 385 ~ 639
28 Real/Cinema GAMMA 0 512/512 385 ~ 639
29 Real/Cinema GAMMA 1 522/527 385 ~ 639
30 Real/Cinema GAMMA 2 518/521 385 ~ 639
31 Real/Cinema GAMMA 3 515/519 385 ~ 639
32 Real/Cinema GAMMA 4 524/516 385 ~ 639
33 Real/Cinema GAMMA 5 512/512 385 ~ 639
34 Real/Cinema GAMMA 6 510/510 385 ~ 639
35 Real/Cinema GAMMA 7 508/508 385 ~ 639
36 Real/Cinema GAMMA 8 505/505 385 ~ 639
37 Real/Cinema GAMMA 9 503/503 385 ~ 639
38 Real/Cinema GAMMA 10 501/501 385 ~ 639
39 Real/Cinema GAMMA 11 499/499 385 ~ 639
40 Real/Cinema GAMMA 12 496/496 385 ~ 639
41 Real/Cinema GAMMA 13 482/482 385 ~ 639
Electrical Adjustments
No. Adjustment Item Initial Value Range Input source / Description

-12-
42 Real/Cinema GAMMA 14 488/488 385 ~ 639
43 Real/Cinema GAMMA 15 512/512 385 ~ 639
44 r_mid2_level 464 0 ~ 1023 _C9D
45 r_mid1_level 560 0 ~ 1023 _C9E
46 r_max_level 632 0 ~ 1023 _C9F
47 g_mid2_level 464 0 ~ 1023 _CA1
48 g_mid1_level 560 0 ~ 1023 _CA2
49 g_max_level 632 0 ~ 1023 _CA3
50 b_mid2_level 464 0 ~ 1023 _CA5
51 b_mid1_level 560 0 ~ 1023 _CA6
52 b_max_level 632 0 ~ 1023 _CA7
53 V-line Correction_R2 0 0 ~ 255 _C48
54 V-line Correction_G2 0 0 ~ 255 _C4D
55 V-line Correction_B2 0 0 ~ 255 _C52
Group: 5 DAC
0B_VIDEO_CENTER 125 0 ~ 255 dac1 ✻Video Center Adj.[B]
1G_VIDEO_CENTER 124 0 ~ 255 dac1 ✻Video Center Adj.[G]
2R_VIDEO_CENTER 125 0 ~ 255 dac1 ✻Video Center Adj.[R]
3REF_B 105 0 ~ 255 dac1 ✻Black Level Adj.[B]
4REF_G 108 0 ~ 255 dac1 ✻Black Level Adj.[G]
5REF_R 107 0 ~ 255 dac1 ✻Black Level Adj.[R]
6NRSB 42 0 ~ 255 NRS B ✻NRS Adj.-1
7NRSA 159 0 ~ 255 NRS A
8-- - ✻NRS Adj.-2
9-- -
10 R_V_COM 69 0 ~ 255 dac2 ✻Common Center Adj.[R]
11 G_V_COM 73 0 ~ 255 dac2 ✻Common Center Adj.[G]
12 B_V_COM 70 0 ~ 255 dac2 ✻Common Center Adj.[B]
13 R_BLK_DC 115/110/115 0 ~ 255 dac3 video/1080i,1035i,720p/480p,525p ✻Pedestal Adj.[R]
14 B_BLK_DC 115/110/115 0 ~ 255 dac3 video/1080i,1035i,720p/480p,525p ✻Pedestal Adj.[B]
15 B_CLMP 30 0 ~ 255 dac4 ✻PC Pedestal Adj.[B]
16 G_CLMP 30 0 ~ 255 dac4 ✻PC Pedestal Adj.[G]
17 R_CLMP 30 0 ~ 255 dac4 ✻PC Pedestal Adj.[R]
Group: 6 AD9883
0pll_divide 938/904 0 ~ 4095 adr01,02(7-4) 625line/525line
1vco_range 0 0 ~ 3 adr03(7-6)
2charge_pump_current 1/1 0 ~ 7 adr03(5-3) 625line/525line
3ad_clk_phase 8/8 0 ~ 31 adr04(7-3) 625line/525line
4clp_placement 128 0 ~ 255 adr05
5clp_width 50 0 ~ 255 adr06
6hsync_out_pulse_width 64 0 ~ 255 adr07
7r_gain 255 0 ~ 255 adr08
8g_gain 255 0 ~ 255 adr09
9b_gain 255 0 ~ 255 adr0A
10 r_offset 60 0 ~ 128 adr0B(7-1) ✻Offset Adj.[R]
11 g_offset 60 0 ~ 128 adr0C(7-1) ✻Offset Adj.[G]
12 b_offset 60 0 ~ 128 adr0D(7-1) ✻Offset Adj.[B]
13 sync_reg 208 0 ~ 255 adr0E
14 clp_corst_pow 154 0 ~ 255 adr0F
15 clp_sel 5 0 ~ 7 adr10(2-0)
16 read_status - 0 ~ 255 read_only adr14
17 ic_ver - 0 ~ 255 read_only adr00
Group: 7 LP05
0LP05_R_GAIN_ud 128 0 ~ 255
1LP05_G_GAIN_ud 128 0 ~ 255
2LP05_B_GAIN_ud 128 0 ~ 255
3LP05_TURBO_GAIN_ud 18 0 ~ 255
4LP05_SHP_EN_SET_ud 805 0 ~ 4095 Set appurture compensation effective period.
5LP05_SHP_EN_RST_ud 14 0 ~ 4095 Set appurture compensation effective period.
6LP05_AB_ON_ud 0 0 ~ 3 Select appurture compensation effective period. 3: 3 point front/back 1: 2 point front/back0: 1 point front/back 2:
Not selection
7LP05_EGE_ud 0 0 ~ 3 Select Frequency characteristics data
Group: 10 Option
0Lamp Time Monitor - - Read only
1RS232C Baudrate 0 0 ~ 1 0: 19200bps 1: 9600bps
2Shootout Mode 0 0 ~ 1 1: Shoot Out Mode Enable 0: Disable
3Cooling Time 3 0 ~ 15 Set cooling period, 1: 30 sec. 3: 90 sec. 15: 450 sec. 0: continus
4Hi-Land SW 0 0 ~ 255 0: Normal 1: Highland mode (Fan spin speed max.)
5V-Douki SW 0 0 ~ 1 0: Syncronized Vertical 1: non-syncronized Vertical
Electrical Adjustments
No. Adjustment Item Initial Value Range Input source / Description

-13-
6Lamp-use time accumulated - - Read only
7Net Board Reset 1 0 ~ 1 0: Invalid , 1: Valid
8Key Stone Option 0 0 ~ 1 0: Fixed, 1: Change with inpt signal
9Logo Off 0 0 ~ 1 0: follow ro menu setting, 1: No logo display
10 Airmouse prohibition 0 0 ~ 1 0: follow to menu setting, 1: prohibition of airmaouse function
10 Auto PC Adj. Disable 0 0 ~ 1 0: fAuto PC Adjust Enable 1:Auto PC Adjust Disable
Group: 11 Fan Control
0FAN_TEMP_A_WARNING 46 30 ~ 100 Temerature to judge abnormal A (Not memorized) Inside projector
1FAN_TEMP_B_WARNING 62 30 ~ 100 Temerature to judge abnormal B (Not memorized) Optical
2FAN_TEMP_C_WARNING 18 0 ~ 100 Temerature to judge abnormal A (Not memorized)Detect the filter clogged
3FAN_CONTROL_SW 0 0 or 1 0: Auto-FanControl 1: Manual
4FAN_A_SPEED 174/251 0 ~ 255 This is effective when FAN_CONTROL_SW is set to “1”.
5FAN_B_SPEED 210/242 0 ~ 255 Normal/Eco mode
6FAN_TEMP_A_MONI - - Read only
7FAN_TEMP_B_MONI - -
8FAN_TEMP_C_MONI
9FAN_PRESSURE - - Read only
Group: 12 PC Real / AV Cinema
0PC Real Contrast 32 0 ~ 63
1PC Real Brightness 32 0 ~ 63
2PC Real Red 32 0 ~ 63
3PC Real Green 32 0 ~ 63
4PC Real Blue 32 0 ~ 63
5PC Real Gamma 8 0 ~ 15
6AV Cinema Contrast 32 0 ~ 63
7AV Cinema Brightness 32 0 ~ 63
8AV Cinema Color 32 0 ~ 63
9AV Cinema Tint 32 0 ~ 63
10 AV Cinema Red 32 0 ~ 63
11 AV Cinema Green 32 0 ~ 63
12 AV Cinema Blue 32 0 ~ 63
13 AV Cinema Sharpness 15 0 ~ 31
14 AV Cinema Gamma 8 0 ~ 15
15 AV Cinema N.R. 0 0 or 1
16 AV Cinema PROGRESSIVE 1 0 or 1
Group: 100 ICS_LP_data
0LP05_R5_VBLKPOL 0 0 ~ 1 R5=ADR133
1LP05_R5_VBLKS 0 0 ~ 2047 Change value automatically according to selected signal.
2LP05_R5_VBLKR 9/14/28/ 0 ~ 2047 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60
28/23/30/35 1080i50 / 720P / 480P / 575P
3LP05_R6_HBLKPOL 0 0 ~ 1 R6=ADR134
4LP05_R6_HBLKS 16 0 ~ 4095 Change value automatically according to selected signal.
5LP05_R6_HBLKR 32 0 ~ 4095 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
6LP05_R7_CLPPOL 0 0 ~ 1 R7=ADR135
7LP05_R7_CLPS 175/175/75/ 0 ~ 4095 Change value automatically according to selected signal.
75/75/156/162 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 /
8LP05_R7_CLPR 270/270/160/ 0 ~ 4095 1080i50 / 720P / 480P / 575P
155/185/260/290
9LP05_R8_VOFFON 0/1 0 ~ 1 R8=ADR136
10 LP05_R8_VOFFS 0 0 ~ 2047 Change value automatically according to selected signal.
11 LP05_R8_VOFFR 0/0/20/20/10/7/7 0 ~ 2047 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
12 LP05_R9_VBLK2POL 0 0 ~ 1 R9=ADR137
13 LP05_R9_VBLK2POS 16 0 ~ 2047 Change value automatically according to selected signal.
14 LP05_R9_VBLK2WID 32 0 ~ 2047 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
15 LP05_RA_HBLK2POL 0 0 ~ 1 RA=ADR138
16 LP05_RA_HBLK2POS 0 0 ~ 4095 Change value automatically according to selected signal.
17 LP05_RA_HBLK2WID 300/300/127/ 0 ~ 4095 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60
120/185/230/265 1080i50 / 720P / 480P / 575P
18 ICS_R0_EnDLS 0 0 ~ 1 R0
19 ICS_R0_EnPLS 1 0 ~ 1 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
20 ICS_R0_Func_Sel 0 0 ~ 1
21 ICS_R0_Fbk_Sel 0 0 ~ 1
22 ICS_R0_Fbk_Pol 0 0 ~ 1
23 ICS_R0_Ref_Pol 1 0 ~ 1
24 ICS_R0_PD_Pol 0 0 ~ 1
25 ICS_R0_Pden 1 0 ~ 1
26 ICS_R1_PSD 2 0 ~ 3 R1
27 ICS_R1_PFD 6 0 ~ 7 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
28 ICS_R3_FBD 2432 0 ~ 8191 R3_R2
Electrical Adjustments
No. Adjustment Item Initial Value Range Input source / Description

-14-
NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
29 ICS_R4_Fil_Sel 0 0 ~ 1 R4
30 ICS_R4_DPA_OS 0 0 ~ 63 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
31 ICS_R5_Mask_Rev 0 0 ~ 63 R5
32 ICS_R5_DPA_Res 0 0 ~ 3 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
33 ICS_R6_Out_Scl 0 0 ~ 3 R6
34 ICS_R6_Ck2_Inv 0 0 ~ 1 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
35 ICS_R6_OE_F 1 0 ~ 1
36 ICS_R6_OE_T2 0 0 ~ 1
37 ICS_R6_OE_P2 0 0 ~ 1
38 ICS_R6_OE_Tck 1 0 ~ 1
39 ICS_R6_OE_Pck 0 0 ~ 1
40 ICS_R7_In_Sel 0 0 ~ 1 R7
41 ICS_R7_Osc_Div 0 0 ~ 127 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
42 ICS_R8_PLL 5 0 ~ 15 R8
43 ICS_R8_DPA 10 0 ~ 15 NTSC & 480i / PAL & SECAM & 525i / 1035i & 1080i60 / 1080i50 / 720P / 480P / 575P
Group: 500 ADC
0ADC R-OFFSET 128 0 ~ 255
1ADC G-OFFSET 128 0 ~ 255
2ADC B-OFFSET 128 0 ~ 255
3ADC R-GAIN 255 0 ~ 255
4ADC G-GAIN 255 0 ~ 255
5ADC B-GAIN 255 0 ~ 255
Group: 502 Keystone Aspect
0ASPECT_SCALE 64 0 ~ 255
1ASPECT_POSITION 64 0 ~ 255
2OSD V Position 0 0 ~ 255
3OSD H Position 0 0 ~ 255
4VScaler 50 0 ~ 255
5VScaler Position 2500 0 ~ 5000
6HScaler 50 0 ~ 255
7HScaler Position 2500 0 ~ 5000
Group: 510 NTSC Gakaku
0NTSC TOTAL DOTS 905 0 ~ 2048 Not used
1NTSC DISP DOTS 1412 0 ~ 2048 NT
2NTSC H BACK PORCTH 295 0 ~ 2048
3NTSC V BACK PORCTH 41 0 ~ 2048
4NTSC DISP LINE 456 0 ~ 2048
5NTSC CLAMP 0 0 ~ 2048
Group: 511 PAL Gakaku
0PAL TOTAL DOTS 939 0 ~ 2048 Not used
1PAL DISP DOTS 1430 0 ~ 2048 PAL
2PAL H BACK PORCTH 296 0 ~ 2048
3PAL V BACK PORCTH 52 0 ~ 2048
4PAL DISP LINE 534 0 ~ 2048
5PAL CLAMP 0 0 ~ 2048
Group: 512 HDTV 1080i-60 Gakaku
0TOTAL DOTS 1203 0 ~ 2048
1DISP DOTS 1024 0 ~ 2048 1080i60
2HBACK PORCTH 145 0 ~ 2048
3VBACK PORCTH 53 0 ~ 2048
4DISP LINE 1052 0 ~ 2048
5CLAMP 7 0 ~ 2048
Group: 513 HDTV 1080i-50 Gakaku
0TOTAL DOTS 1444 0 ~ 2048
1DISP DOTS 1024 0 ~ 2048 1080i50
2HBACK PORCTH 144 0 ~ 2048
3VBACK PORCTH 53 0 ~ 2048
4DISP LINE 1052 0 ~ 2048
5CLAMP 7 0 ~ 2048
Group: 514 HDTV 1035i Gakaku
0TOTAL DOTS 1203 0 ~ 2048
1DISP DOTS 1024 0 ~ 2048 1035i (tempolary)
2HBACK PORCTH 144 0 ~ 2048
3VBACK PORCTH 89 0 ~ 2048
4DISP LINE 1012 0 ~ 2048
5CLAMP 7 0 ~ 2048
Group: 515 HDTV 720p Gakaku
No. Adjustment Item Initial Value Range Input source / Description
Electrical Adjustments

-15-
0TOTAL DOTS 1650 0 ~ 2048
1DISP DOTS 1248 0 ~ 2048 720p
2HBACK PORCTH 318 0 ~ 2048
3VBACK PORCTH 34 0 ~ 2048
4DISP LINE 700 0 ~ 2048
5CLAMP 8 0 ~ 2048
Group: 516 HDTV 575p Gakaku
0TOTAL DOTS 1408 0 ~ 2048
1DISP DOTS 1024 0 ~ 2048 575p
2HBACK PORCTH 296 0 ~ 2048
3VBACK PORCTH 48 0 ~ 2048
4DISP LINE 542 0 ~ 2048
5CLAMP 8 0 ~ 2048
Group: 517 HDTV 480p Gakaku
0TOTAL DOTS 1285 0 ~ 2048
1DISP DOTS 1024 0 ~ 2048 480p (top bottom left right 7)
2HBACK PORCTH 214 0 ~ 2048
3VBACK PORCTH 47 0 ~ 2048
4DISP LINE 460 0 ~ 2048
5CLAMP 7 0 ~ 2048
Group: 518 RGB NTSC Gakaku
0TOTAL DOTS 1330 0 ~ 2048
1DISP DOTS 1024 0 ~ 2048 RGB NTSC
2HBACK PORCTH 223 0 ~ 2048
3VBACK PORCTH 43 0 ~ 2048
4DISP LINE 462 0 ~ 2048
5CLAMP 1 0 ~ 2048
Group: 519 RGB PAL Gakaku
0TOTAL DOTS 1366 0 ~ 2048
1DISP DOTS 1024 0 ~ 2048 RGB PAL
2HBACK PORCTH 250 0 ~ 2048
3VBACK PORCTH 57 0 ~ 2048
4DISP LINE 546 0 ~ 2048
5CLAMP 4 0 ~ 2048
Group: 900 LC24049 Timing Controller
0HCK PHASE 10 0 ~15
1RCK PHASE ADJ 16 0 ~ 255
2GCK PHASE ADJ 16 0 ~ 255
3BCK PHASE ADJ 16 0 ~ 255
No. Adjustment Item Initial Value Range Input source / Description
Electrical Adjustments

MB8XP4101/MB8-XP41L01
-16-
■Electrical Parts List
Product safety should be considered when a component replacement is made in any area of a projector.
Components indicated by a !mark in this parts list and the circuit diagram show components whose value have
special significance to product safety. It is particularly recommended that only parts specified on the following parts
list be used for components replacement pointed out by the mark.
Read description in the Capacitor and Resistor as follows:
CAPACITOR CERAMIC 100P K 50V
Rated Voltage
Tolerance Symbols:
Less than 10pF
A : Not specified B : ±0.1pF C : ±0.25pF
D : ±0.5pF E : +0 -1pF F : ±1PF
G : ±2pF H : +0.1 -0pF L : +0 -0.1pF
R : ±0.25 -0pF S : +0-0.25pF
More than 10pF
A : Not specified B : ±0.1% C : ±0.25%
D : ±0.5% F : ±1% G : ±2%
H : ±3% J : ±5% K : ±10%
L : ±15% M : ±20% N : ±30%
P : +100-0% Q : +30-10% T : +50-10%
U : +75-10% V : +20-10% W : +100-10%
X : +40-20% Y : +150-10% Z : +80-20%
Rated value: P=pico farad, U=micro farad
Material:
CERAMIC........... Ceramic
MT-PAPER......... Metallized Paper
POLYESTER...... Polyester
MT-POLYEST.....Metallized Polyester
POLYPRO.......... Polypropylene
MT-POLYPRO....Metallized Polypropylene
COMPO FILM.....Composite film
MT-COMPO........Metallized Composite
STYRENE...........Styrene
TA-SOLID........... Tantalum Oxide Solid Electrolytic
AL-SOLID........... Aluminium Solid Electrolytic
ELECT................ Aluminum Foil Electrolytic
NP-ELECT..........Non-polarised Electrolytic
OS-SOLID.......... Aluminium Solid with Organic Semiconductive Electrolytic
POS-SOLID........ Polymerized Organic Semiconductive
DL-ELECT.......... Double Layered Electrolytic
PPS-FILM...........Polyphenylene Sulfide Film
MT-PPS-FILM.....Metalized Polyphenylene Sulfide Film
MT-PEN-FILM.....Metalized Polyethylenenaphthalate Film
CAPACITOR.......Other
CARBON 4.7K J A 1/4W
Rated Wattage
Performance Symbols:
A: General B: Non flammable Z: Low noise
Other: Temperature coefficient
Tolerance Symbols:
A: ±0.05% B: ±0.1% C: ±0.25% D: ±0.5%
F: ±1% G: ±2% J: ±5% K: ±10%
M: ±20% P: +5-15% Z: 0 ohm
Rated value, ohms:
K: 1,000, M: 1,000,000
Material:
CARBON........... Carbon
MT-FILM............ Metal Film
OXIDE-MT......... Oxide Metal Film
SOLID................ Composition
MT-GLAZE......... Metal Glaze
WIRE WOUND...Wire Wound
CERAMIC RES.. Ceramic
FUSIBLE RES....Fusible
RESISTOR ........Other
T: ±10ppm/°C U: ±25ppm/°C C: ±50ppm/°C
D: ±100ppm/°C E: ±200ppm/°C F: ±250ppm/°C
G: ±350ppm/°C H: ±1000ppm/°C±10% W: ±1200ppm/°C±10%
Y: ±1400ppm/°C±10% J: ±2000ppm/°C±10% K: ±2400ppm/°C±10%
L: ±2700ppm/°C±10% M: ±3000ppm/°C±10% N: ±3300ppm/°C±10%
P: ±3600ppm/°C±10% Q: ±3900ppm/°C±10% R: ±4200ppm/°C±10%
S: ±4300ppm/°C±10% V: ±4500ppm/°C±10% X: ±8000ppm/°C±10%
RESISTOR
●Read Description in the parts list

MB8XP4101/MB8-XP41L01
-17-
Electrical Parts List
●OUT OF CIRCUIT BOARD
F601
Fuse
Power Board
Thermal Switch
(SW905)
Note: Parts order must contain Chassis No., Part No., and Descriptions.
FN901
Cooling Fan
Connect
Board
FN904
Cooling Fan
Interlock switch
(SW902)
Drive Board
RC1 Board
AV Board
Main Board
Line Filter
Board
Lamp Ballast
Board FN902
Cooling Fan
FN905
Cooling Fan
Sensor1
Board
FN903
Cooling Fan
FN906
Cooling Fan
Sub Power
Board

MB8XP4101/MB8-XP41L01
Electrical Parts List
-18-
!610 293 1815 ASSY,PWB,CONTROL MA8A
!610 293 1839 SSY,PWB,RC FRONT MA8A
!610 293 1846 ASSY,PWB,CONNECT MA8A
!610 294 8233 ASSY,PWB,SENSOR 1 MA8A
!610 296 7951 ASSY,PWB,MAIN MA8AA
!610 296 9351 ASSY,PWB,A/V MA8AA
!610 296 9368 ASSY,PWB,I/F MA8AA
!610 316 4373 ASSY,PWB,POWER MK3AA
!610 316 4380 ASSY,PWB,SUB POWER MK3AA
!610 316 4397 ASSY,PWB,DRIVE MK3AA
!610 316 4403 ASSY,PWB,FILTER MK3AA
COIL
!L901 645 003 3834 CORE,FERRITE
!L902 645 003 3834 CORE,FERRITE
!LF901 645 045 2154 UNIT,NOISE FILTER
!LP900 610 297 3891 COMPL,OPTICAL LAMP-MA8AA
!A901 645 051 9338 UNIT,BALLAST
!FN901 645 047 9700 MOTOR,FAN DC 11W
!FN902 645 047 9700 MOTOR,FAN DC 11W
!FN903 645 053 7523 MOTOR,FAN DC 1.68W
!FN904 645 053 7523 MOTOR,FAN DC 1.68W
!FN905 645 047 9489 MOTOR,FAN DC 5.28W
!FN906 645 048 4001 MOTOR,FAN DC 2.4W
!FN907 645 052 9313 MOTOR,FAN DC 2.04W
SP901 645 047 7584 SPEAKER,8
SP902 645 047 7584 SPEAKER,8
!SW902 645 031 7743 SWITCH,PUSH 2P-2TX2
!SW905 645 050 3580 SWITCH,THERMAL
W16I&8X 610 296 5476 CORD SHIELD 6P 1.5MM
W16M 610 296 0617 CONVERT CORD 4P
W16R&8T 645 050 4389 CORD,ID CONNECTOR
W16S&10T 645 051 7594 CORD,ID CONNECTOR
W28A&8U 645 050 4402 CORD,ID CONNECTOR
W66D&8D 645 049 4802 CORD,ID CONNECTOR
W66E&8E 645 049 4765 CORD,ID CONNECTOR
W66F&8G 645 050 4396 CORD,ID CONNECTOR
W66Q&66G 645 050 4372 CORD,ID CONNECTOR
W68A&8J 645 050 4426 CORD,ID CONNECTOR
W70A&8Q 645 053 7738 CORD,ID CONNECTOR
W70B&66N 645 053 7721 CORD,ID CONNECTOR
W70D&8Y 645 049 9081 CORD,ID CONNECTOR
W9B&16L 645 050 4358 CORD,ID CONNECTOR
W9C&8S 645 026 7017 CORD,ID CONNECTOR
WCN2&8W 645 026 7017 CORD,ID CONNECTOR
610 293 1815 ASSY,PWB,CONTROL MA8A
CAPACITOR
C6871 403 164 0204 CERAMIC 0.1U Z 25V
C6881 403 164 0204 CERAMIC 0.1U Z 25V
C6891 403 164 0204 CERAMIC 0.1U Z 25V
C6892 403 164 0204 CERAMIC 0.1U Z 25V
RESISTOR
R6871 401 105 2904 MT-GLAZE 22K JA 1/16W
R6872 401 105 1600 MT-GLAZE 15K JA 1/16W
R6873 401 105 6001 MT-GLAZE 5.6K JA 1/16W
R6874 401 105 5301 MT-GLAZE 4.7K JA 1/16W
R6875 401 105 3307 MT-GLAZE 2.7K JA 1/16W
R6876 401 105 4106 MT-GLAZE 3.3K JA 1/16W
R6878 401 105 5202 MT-GLAZE 470 JA 1/16W
R6887 401 105 1501 MT-GLAZE 1.5K JA 1/16W
R6888 401 105 5202 MT-GLAZE 470 JA 1/16W
R6891 401 105 2904 MT-GLAZE 22K JA 1/16W
R6892 401 105 3802 MT-GLAZE 30K JA 1/16W
R6893 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R6894 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R6895 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R6896 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
R6897 401 105 1501 MT-GLAZE 1.5K JA 1/16W
R6898 401 105 5202 MT-GLAZE 470 JA 1/16W
DIODE
D6871 407 223 0501 ZENER DIODE 02DZ12Y(TPH3)
D6872 407 223 0501 ZENER DIODE 02DZ12Y(TPH3)
D6881 407 223 0501 ZENER DIODE 02DZ12Y(TPH3)
D6891 407 223 0501 ZENER DIODE 02DZ12Y(TPH3)
D6892 407 203 7803 LED SML-210LT T86 M
D6893 407 203 7902 LED SML-210MT T86 M
D6894 407 203 7803 LED SML-210LT T86 M
D6895 407 203 7704 LED SML-210DT T86 L
MISCELLANEOUS
SW6871 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6872 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6873 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6874 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6875 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6876 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6878 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6887 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6888 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6891 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6892 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6897 645 026 2791 SWITCH,PUSH 1P-1TX1
SW6898 645 026 2791 SWITCH,PUSH 1P-1TX1
610 293 1839 ASSY,PWB,RC FRONT MA8A
CAPACITOR
C2801 403 283 6309 CERAMIC 1U Z 10V
C2802 403 157 6206 CERAMIC 220P K 50V
C2803 403 304 2105 ELECT 47U M 6.3V
RESISTOR
R2801 401 105 0405 MT-GLAZE 100 JA 1/16W
R2802 407 225 0202 DIODE RB751S-40
R2803 401 105 7909 MT-GLAZE 0.000 ZA 1/16W
MISCELLANEOUS
AU2801 645 034 5029 UNIT,REMOCON RECEIVER
610 294 8233 ASSY,PWB,SENSOR 1 MA8A
INTEGRATED CIRCUIT
IC1691 409 481 8602 IC LM76CHMX-5
CAPACITOR
SENSOR 1 BOARD
RC FRONT BOARD
CONTROL BOARD
OUT OF CIRCUIT BOARDS
ASSEMBLIED BOARDS
Key No. Part No. Description Key No. Part No. Description

MB8XP4101/MB8-XP41L01
-19-
Electrical Parts List
C1691 403 281 5205 CERAMIC 0.22U Z 16V
C1692 403 155 1609 CERAMIC 33P J 50V
C1693 403 155 1609 CERAMIC 33P J 50V
RESISTOR
R1691 401 105 0405 MT-GLAZE 100 JA 1/16W
R1692 401 105 0306 MT-GLAZE 10 JA 1/16W
R1693 401 105 0306 MT-GLAZE 10 JA 1/16W
610 296 7951 ASSY,PWB,MAIN MA8AA
TRANSISTOR
Q1101 405 014 4509 TR 2SC2412K T146 R
Q1141 405 134 5905 TR 2SA1037AK-T146-R
Q1142 405 134 5905 TR 2SA1037AK-T146-R
Q1143 405 014 4509 TR 2SC2412K T146 R
Q1144 405 134 5905 TR 2SA1037AK-T146-R
Q1145 405 014 4509 TR 2SC2412K T146 R
Q1146 405 134 5905 TR 2SA1037AK-T146-R
Q1147 405 134 5905 TR 2SA1037AK-T146-R
Q1148 405 134 5905 TR 2SA1037AK-T146-R
Q1149 405 014 4509 TR 2SC2412K T146 R
Q1151 405 134 5905 TR 2SA1037AK-T146-R
Q1161 405 134 5905 TR 2SA1037AK-T146-R
Q1163 405 134 5905 TR 2SA1037AK-T146-R
Q141 405 014 4509 TR 2SC2412K T146 R
Q142 405 014 4509 TR 2SC2412K T146 R
Q143 405 014 4509 TR 2SC2412K T146 R
Q144 405 134 5905 TR 2SA1037AK-T146-R
Q145 405 014 4509 TR 2SC2412K T146 R
Q146 405 014 4509 TR 2SC2412K T146 R
Q147 405 014 4509 TR 2SC2412K T146 R
Q148 405 134 5905 TR 2SA1037AK-T146-R
Q149 405 014 4509 TR 2SC2412K T146 R
Q2101 405 014 4509 TR 2SC2412K T146 R
Q2102 405 014 4509 TR 2SC2412K T146 R
Q2301 405 014 4509 TR 2SC2412K T146 R
Q2302 405 014 4509 TR 2SC2412K T146 R
Q2303 405 014 4509 TR 2SC2412K T146 R
Q2304 405 079 2809 TR IMX1-T110
Q2305 405 014 4509 TR 2SC2412K T146 R
Q2501 405 014 4509 TR 2SC2412K T146 R
Q2511 405 014 4509 TR 2SC2412K T146 R
Q2521 405 014 4509 TR 2SC2412K T146 R
Q3103 405 014 4509 TR 2SC2412K T146 R
Q3111 405 134 5905 TR 2SA1037AK-T146-R
Q3112 405 134 5905 TR 2SA1037AK-T146-R
Q3113 405 134 5905 TR 2SA1037AK-T146-R
Q3116 405 014 4509 TR 2SC2412K T146 R
Q3117 405 014 4509 TR 2SC2412K T146 R
Q3118 405 014 4509 TR 2SC2412K T146 R
Q3301 405 014 4509 TR 2SC2412K T146 R
Q3302 405 014 4509 TR 2SC2412K T146 R
Q3571 405 014 4509 TR 2SC2412K T146 R
Q3601 405 002 8304 TR 2SA1203-Y-TE12L
Q3602 405 014 4509 TR 2SC2412K T146 R
Q4101 405 014 4509 TR 2SC2412K T146 R
Q4102 405 134 5905 TR 2SA1037AK-T146-R
Q4103 405 014 4509 TR 2SC2412K T146 R
Q4151 405 014 4509 TR 2SC2412K T146 R
Q4152 405 014 4509 TR 2SC2412K T146 R
Q4161 405 014 4509 TR 2SC2412K T146 R
Q4162 405 014 4509 TR 2SC2412K T146 R
Q4171 405 014 4509 TR 2SC2412K T146 R
Q4172 405 014 4509 TR 2SC2412K T146 R
Q4182 405 014 4509 TR 2SC2412K T146 R
Q4185 405 134 5905 TR 2SA1037AK-T146-R
Q4801 405 134 5905 TR 2SA1037AK-T146-R
Q4802 405 134 5905 TR 2SA1037AK-T146-R
Q4803 405 134 5905 TR 2SA1037AK-T146-R
Q4804 405 134 5905 TR 2SA1037AK-T146-R
Q4805 405 014 4509 TR 2SC2412K T146 R
Q4807 405 014 4509 TR 2SC2412K T146 R
Q4808 405 014 4509 TR 2SC2412K T146 R
Q9801 405 134 5905 TR 2SA1037AK-T146-R
Q9802 405 014 4509 TR 2SC2412K T146 R
INTEGRATED CIRCUIT
IC1101 409 453 9309 IC UPD64082GF-3BA
IC1131 410 342 8808 IC MSM54V16258BSL-40TS-K
IC1141 409 051 2900 IC TC4053BF(EL)
IC1161 409 416 6406 IC BA033FP-E2
IC141 410 300 4804 IC MM1031XM
IC1501 409 502 3302 IC L3E06070D0A
IC1531 409 502 3302 IC L3E06070D0A
IC1561 409 502 3302 IC L3E06070D0A
IC1801 409 475 3705 IC M66500FP
IC1802 410 364 6905 IC TC74ACT138FT-EL
IC1841 409 521 8708 IC MC74HCT244A
410 315 5506 IC HD74HCT244TV
IC1851 410 398 2706 IC LC863316A-5W09
IC1871 409 481 8602 IC LM76CHMX-5
IC1872 409 481 8602 IC LM76CHMX-5
IC201 409 470 2604 IC AD8183ARU-REEL7
IC2101 409 504 5007 IC TC90A69F
IC211 409 357 6602 IC LT1260CS
IC212 409 458 3401 IC M62393FP
IC213 410 343 7008 IC SN74AHCT1G14DBVR
IC2301 409 523 4807 IC AD9883AKST-110
410 528 7007 IC AD9883AKSTZ-110
IC2302 409 416 6406 IC BA033FP-E2
409 410 1001 IC UPC2933T-E1
IC2303 409 416 6406 IC BA033FP-E2
409 410 1001 IC UPC2933T-E1
IC231 409 504 8206 IC AD9886KS-140
409 502 3104 IC AD9887KS-140
IC232 409 416 6406 IC BA033FP-E2
409 410 1001 IC UPC2933T-E1
IC233 409 323 8906 IC TC4W53FU(TE12L)
IC234 409 416 6406 IC BA033FP-E2
409 410 1001 IC UPC2933T-E1
IC2381 409 458 3401 IC M62393FP
IC301 409 501 8308 IC PW365-10U
IC304 409 339 3605 IC 24LC16BT/SN-T
IC306 409 301 5309 IC TC7S32FU-TE85L
IC3101 409 504 9005 IC TB1274AF
IC3102 409 416 6505 IC BA05FP-E2
IC3103 409 416 6505 IC BA05FP-E2
IC3211 410 321 8300 IC TC74VCX16244FT
IC3212 410 321 8300 IC TC74VCX16244FT
IC3213 410 321 8300 IC TC74VCX16244FT
IC3214 410 362 6501 IC TC74LCX541FT
IC3221 409 429 6806 IC TC74LCX74FT-(EL)
IC3224 410 362 6501 IC TC74LCX541FT
IC3231 410 358 1503 IC TC74HC4053AFT(EL)
IC3381 409 398 1901 IC L88MS05TL-TL
IC341 410 530 3707 IC IC61LV6416-15T
IC3501 409 428 9600 IC M62399FP
IC3502 409 431 2308 IC BA12FP-E2
IC351 410 491 8209 IC MBM29LV800TA90B989CS
IC3551 409 428 9600 IC M62399FP
IC361 409 501 9107 IC ICS512MT
MAIN BOARD
Key No. Part No. Description Key No. Part No. Description

MB8XP4101/MB8-XP41L01
Electrical Parts List
-20-
IC3611 409 502 3203 IC L3E01031F0A
IC362 409 501 9107 IC ICS512MT
IC3631 409 502 3203 IC L3E01031F0A
IC3651 409 502 3203 IC L3E01031F0A
IC3671 409 390 0001 IC LM7171AIMX
409 486 7709 IC LM7171BIMX
IC3681 409 343 0201 IC LT1206CS8
IC391 409 416 6406 IC BA033FP-E2
409 410 1001 IC UPC2933T-E1
IC392 409 534 1703 IC SI-3025LSA-TL
IC401 409 502 3401 IC L3E07050 K0A
IC4101 409 474 0002 IC CXA2101AQ
IC4111 409 422 5400 IC MC74AC04DT
409 423 7205 IC TC74AC04FT
410 357 4208 IC SN74LV04APWR
IC4181 409 051 2900 IC TC4053BF(EL)
IC4201 409 498 4406 IC T8F01HF
IC4211 409 498 6103 IC LM385M-1.2
IC4231 409 444 8700 IC ICS1523M-ER
IC4232 409 439 8906 IC TC7WH125FU
IC4261 409 344 1900 IC MN1382-Q-TX
IC4501 410 403 7900 IC LC24085BT-UG4
410 505 5903 IC LC98500BT-YE5-E
IC451 409 534 1703 IC SI-3025LSA-TL
IC4551 409 504 4901 IC TA1287F
IC4801 409 416 6406 IC BA033FP-E2
409 410 1001 IC UPC2933T-E1
IC501 409 502 3302 IC L3E06070D0A
IC531 409 502 3302 IC L3E06070D0A
IC561 409 502 3302 IC L3E06070D0A
IC6301 410 365 4603 IC MS82V16520-8AGA
IC8001 410 451 8805 IC SII161BCT100
IC8003 409 051 2900 IC TC4053BF(EL)
IC8004 409 487 5803 IC 24C01CT/SN
IC801 410 406 5408 IC HD64F7045F28-B867
IC802 409 344 1900 IC MN1382-Q-TX
IC803 410 491 7202 IC MBM29F160BE-90-C225BS
IC804 410 365 1602 IC M5M51008BFP-70LL
410 352 4302 IC M5M51008BFPP-70L
410 415 5208 IC M5M51008DFP-70HI
410 367 1501 IC M5M51008CFP-70HI
IC808 409 339 3605 IC 24LC16BT/SN-T
IC811 409 155 8006 IC TC7S04F-TE85L
IC812 410 325 4704 IC HD74LVC244AT
IC813 409 152 5404 IC TC7S08F-TE85L
IC814 410 362 6501 IC TC74LCX541FT
IC815 410 362 6501 IC TC74LCX541FT
IC816 410 362 6600 IC TC74ACT541FT
IC9401 410 403 7900 IC LC24085BT-UG4
410 505 5903 IC LC98500BT-YE5-E
IC9801 409 468 8908 IC ML60851CTB
409 521 4502 IC ML60851DTB
IC9821 409 521 8708 IC MC74HCT244A
410 315 5506 IC HD74HCT244TV
IC9822 409 327 6700 IC TC7W02FU-TE12L
CAPACITOR
C1101 403 164 0204 CERAMIC 0.1U Z 25V
C1102 403 164 0204 CERAMIC 0.1U Z 25V
C1103 403 164 0204 CERAMIC 0.1U Z 25V
C1105 403 321 2607 ELECT 10U M 16V
C1106 403 164 0204 CERAMIC 0.1U Z 25V
C1107 403 164 0204 CERAMIC 0.1U Z 25V
C1108 403 164 0204 CERAMIC 0.1U Z 25V
C1109 403 164 0204 CERAMIC 0.1U Z 25V
C1111 403 304 1801 ELECT 100U M 6.3V
C1112 403 164 0204 CERAMIC 0.1U Z 25V
C1113 403 164 0204 CERAMIC 0.1U Z 25V
C1114 403 164 0204 CERAMIC 0.1U Z 25V
C1115 403 304 1801 ELECT 100U M 6.3V
C1116 403 145 9905 CERAMIC 22P J 50V
C1117 403 145 9905 CERAMIC 22P J 50V
C1118 403 164 0204 CERAMIC 0.1U Z 25V
C1119 403 164 0204 CERAMIC 0.1U Z 25V
C1121 403 164 0204 CERAMIC 0.1U Z 25V
C1122 403 215 0900 CERAMIC 390P J 50V
C1123 403 164 0204 CERAMIC 0.1U Z 25V
C1124 403 304 2105 ELECT 47U M 6.3V
C1125 403 164 0204 CERAMIC 0.1U Z 25V
C1127 403 283 6309 CERAMIC 1U Z 10V
C1128 403 164 0204 CERAMIC 0.1U Z 25V
C1131 403 283 6309 CERAMIC 1U Z 10V
C1132 403 304 1801 ELECT 100U M 6.3V
C1133 403 283 6309 CERAMIC 1U Z 10V
C1134 403 283 6309 CERAMIC 1U Z 10V
C1141 403 164 0204 CERAMIC 0.1U Z 25V
C1142 403 149 9208 CERAMIC 0.01U Z 50V
C1143 403 304 3300 ELECT 47U M 16V
C1144 403 164 0204 CERAMIC 0.1U Z 25V
C1145 403 321 2607 ELECT 10U M 16V
C1146 403 283 6309 CERAMIC 1U Z 10V
C1148 403 164 0204 CERAMIC 0.1U Z 25V
C1161 403 304 1801 ELECT 100U M 6.3V
C1162 403 164 0204 CERAMIC 0.1U Z 25V
C1163 403 145 9905 CERAMIC 22P J 50V
C1165 403 145 9905 CERAMIC 22P J 50V
C1166 403 175 4802 NP-ELECT 10U M 10V
C141 403 162 6208 ELECT 1U M 50V
C142 403 175 4802 NP-ELECT 10U M 10V
C143 403 164 0204 CERAMIC 0.1U Z 25V
C144 403 321 2607 ELECT 10U M 16V
C145 403 283 6309 CERAMIC 1U Z 10V
C146 403 164 0204 CERAMIC 0.1U Z 25V
C147 403 304 3300 ELECT 47U M 16V
C148 403 283 6309 CERAMIC 1U Z 10V
C149 403 266 8108 NP-ELECT 1U M 50V
C1501 403 304 1801 ELECT 100U M 6.3V
C1502 403 164 0204 CERAMIC 0.1U Z 25V
C1503 403 164 0204 CERAMIC 0.1U Z 25V
C1504 403 164 0204 CERAMIC 0.1U Z 25V
C1507 403 164 0204 CERAMIC 0.1U Z 25V
C1508 403 164 0204 CERAMIC 0.1U Z 25V
C1509 403 164 0204 CERAMIC 0.1U Z 25V
C151 403 283 6309 CERAMIC 1U Z 10V
C1511 403 304 3300 ELECT 47U M 16V
C1512 403 164 0204 CERAMIC 0.1U Z 25V
C1513 403 149 9208 CERAMIC 0.01U Z 50V
C1514 403 164 0204 CERAMIC 0.1U Z 25V
C1531 403 304 1801 ELECT 100U M 6.3V
C1532 403 164 0204 CERAMIC 0.1U Z 25V
C1533 403 164 0204 CERAMIC 0.1U Z 25V
C1534 403 164 0204 CERAMIC 0.1U Z 25V
C1537 403 164 0204 CERAMIC 0.1U Z 25V
C1538 403 164 0204 CERAMIC 0.1U Z 25V
C1539 403 164 0204 CERAMIC 0.1U Z 25V
C1541 403 304 3300 ELECT 47U M 16V
C1542 403 164 0204 CERAMIC 0.1U Z 25V
C1543 403 149 9208 CERAMIC 0.01U Z 50V
C1544 403 164 0204 CERAMIC 0.1U Z 25V
C1561 403 304 1801 ELECT 100U M 6.3V
C1562 403 164 0204 CERAMIC 0.1U Z 25V
C1563 403 164 0204 CERAMIC 0.1U Z 25V
C1564 403 164 0204 CERAMIC 0.1U Z 25V
C1567 403 164 0204 CERAMIC 0.1U Z 25V
C1568 403 164 0204 CERAMIC 0.1U Z 25V
Key No. Part No. Description Key No. Part No. Description