Sanyo DC-DA380 User manual

INSTRUCTION MANUAL DC-DA380
Micro Component System
(AU) 1AD6P1P1337-P SANYO Electric Co., Ltd.
Printed in China
MAINTENANCE
Cleaning the tape heads
To ensure continued high performance, use cotton swab to clean the
heads, pinch roller and capstan of the deck after about every 10 hours
of use. If the dirt persists, soak the swab in a little methylated spirit or
head cleaning fluid and then clean.
1. Cotton swab
3, 7. Capstan
4, 6. Pinch roller
2, 5. Heads
Cleaning the CD player lens
The lens should never be touched. If dust is on the lens, blow it off using
a camera lens blower. (Consult your dealer.)
Cleaning the unit
Clean the outside of the unit with a clean soft cloth, moistened with
lukewarm water. Do not use benzene, thinner of alcohol since they will
mar the finish of the surfaces.
-10-
Tuner
Reception frequency:
FM: 87.5 - 108 MHz
AM: 522 -1710 kHz (9 kHz step)
520 - 1710 kHz (10 kHz step)
CD player
Channels:
2-channel stereo
Sampling frequency:
44.1 kHz
Pick-up:
Optical 3-beam semiconductor laser
Laser output:
0.6 mW (Continuous wave max.)
Wave length:
790 nm
Wow/flutter:
Below measurable limits
Cassette deck
Track system:
4-track, 2-channel stereo
Frequency response:
60 Hz to 13.5 kHz
Signal-to-noise ratio:
50 dB
Wow/flutter:
0.12% (WRMS)
Fast forward/rewind time:
Approx. 110 sec. (C-60)
General
Output power:
12.5 W x 2 (at 4 ohms, 10% distortion)
Input
VIDEO IN: 400 mV/50k ohms
Outputs
SPEAKERS: 4 ohms
PHONES: 8 - 32 ohms
Power requirements:
AC 230 - 240 V, 50 Hz
Power consumption:
40 W
Dimensions:
160(W) x 251(H) x 207(D) mm
Weight:
3.2 kg
Speaker systems
Type:
3 way bass reflex
Unit used:
Woofer: 10 cm cone type
Mid range: 5 cm cone type
Tweeter: 2 cm piezoelectric
Maximum power-handling capacity:
25 W (peak)
Nominal impedance:
4 ohms
Dimensions:
150(W) x 245(H) x 224(D) mm
Weight:
1.9 kg (per speaker)
Specifications subject to change without notice.
SPECIFICATIONS
3
2
1
7
456
TIMER OPERATION
Using the timer (Main unit only)
Set the on and off times, and function to be used. Operation will start with
the selected function at the on time. The sound will be gradually
increased from a no-sound level to the current volume setting (fade-in).
The power will be switched off at the off time.
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before
setting the timer.
- Prepare the sources to be used.
- If the function selected is tuner, tune in to the desired band and
station.
- For tape deck: Tape playback will start in the forward direction.
- Adjust the volume level as desired.
Operation
1. Press the FUNCTION button to select the function and set the
desired volume level for timer operation.
2. Press the CLOCK/TIMER button for at least 2 seconds.
The previous timer on time setting appears.
3. Press the MEMORY button within 10 seconds.
4. Set the timer on time by turning the VOLUME control, then press the
MEMORY button (as described under “ADJUDTING THE CLOCK”).
The timer off time setting appears.
5. Set the timer off time as described in step 4.
The previous timer mode/function setting appears.
-“
” blinks only for tuner function, “ ” remains lit for other function.
6. Select the timer mode by turning the VOLUME control (Tuner
function only).
-“
REC” and “ ” blink alternately. Select “ REC” for unattention
recording.
7. Press the MEMORY button (Tuner function only).
The original display returns, then the timer operation standby mode
is activted. “ ” or “ REC” remains lit.
8. Press the z/ON button to switch off the power.
- To switch off the power during a timer controlled operation, press
the z/ON button. The timer will be set in the standby mode.
To release the timer
After turning the power on, press the CLOCK/TIMER button twice. “ ”
or “ REC” disappears.
To set the timer again with the same settings
1. Press the CLOCK/TIMER button repeatedly to display “ ” or “
REC”.
2. Press the z/ON button to switch off the power.
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer (Remote control only)
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
“SLEEP” blinks and the selected time appears on the display. After a few
seconds, the original display returns. “SLEEP” remains blinking.
To check the remaining sleep time
Press the SLEEP button once. After a few seconds, the original display
returns.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until “SLEEP” disappears. The
timer is also released if the power is switched off.
-9-
RECORDING
Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copy-
right material, permission from the copyright owner is necessary.
SANYO does not approve of, and cannot be held responsible for,
any unlawful use of this machine.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during the
recording of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. While “PROG.” is blinking, press the Ubutton to select “bc-1” or
“bc-2”. Select the setting that gives the best results.
Automatic record muting (Remote control only)
Undesirable parts of a programme can be omitted while recording.
Press the rbutton once while recording. “REC” blinks and a 5-second
unrecorded blank space is created, then the deck enters the recording
pause mode. “REC” remains lit and “a” or “b” blinks on the display.
- To add another 5-second blank space, press the rbutton again.
- To resume recording, press the aor bbutton (to match the blinking
“a” or “b”).
Safeguards against accidental erasure
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement.
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive tape and the tape can be used for
recording again.
Break out tab A for side A.
Break out tab B for side B.
Preparation
1. Press the FUNCTION button to select “TAPE”.
2. Load a blank cassette.
3. Press the Ubutton to select the reverse mode.
S: For recording one side only.
W: For recording both sides in succession.
- If recording has been started from the reverse side, only the
reverse side will be recorded.
- If a tape with one of its tabs already broken out is used for
recording, the tape will not be reversed automatically, and it will
stop.
- If the reverse mode has been set to “U”, “W” appears
automatically when the recording mode is established.
Recording compact discs (Synchronous recording)
1. Select “CD” function.
2. Load the disc to be recorded.
- For programmed recording, programme the material in advance
(as described under “PROGRAMMED PLAY”).
3. Select the track number to be recorded if required.
- For programmed recording, this step is unnecessary.
4. Press the jbutton (or the mbutton on the remote control). The
deck enters the recording pause mode and “REC” appears. “b a”
blinks.
5. Press the aor bbutton. Recording starts.
6. Press the nbutton to stop recording. Also the CD player stops
automatically.
Recording from the tuner or other sources
1. Tune in the radio station to be recorded or play other sources.
2. Press the jbutton.
3. Press the aor bbutton. Recording starts.
4. Press the nbutton to stop recording.
Side A
Side B
LISTENING TO OTHER SOURCES
1. Press the FUNCTION button to select “VIDEO: AUX”. 2. Follow the instructions supplied with the Video/ Auxiliary equipment.
-8-
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears, press the
FM MODE button to turn the “MONO” indication off.
“ST” appears when an FM stereo broadcast is received.
- If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to the MONO mode. The
reception may be improved, but the sound will be monaural.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during reception
of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. When “PROG.” is blinking, press the FM MODE button to select “bc-
A” or “bc-B”. Select the setting that gives the best results.
W: For listening to both sides of the tape in succession.
- If playback has been started from the reverse side, only the
reverse side will be played back.
U: For listening repeatedly to both sides of the tape.
LISTENING TO TAPES
LISTENING TO THE RADIO
-7-
If a cassette is loaded, you can turn the unit on and begin play
immediately by pressing the aor bbutton.
1. Press the FUNCTION button to select
“TAPE”.
2. Press the cassette holder (EJECT portion)
to open it.
3. Load the cassette.
After loading the cassette, push the cas-
sette holder (EJECT portion) back into
position. “ ” appears.
4. Press the Ubutton to select the reverse
mode as desired.
S: For listening to one side of the tape
only.
5. Press the aor bbutton to begin playback. “a” or “b” appears.
a: For forward play
b: For reverse play.
6. Press the nbutton to stop playback at any time.
When the end of the tape has been reached, automatic stop or
reverse will be activated.
Note:
- Use the normal tape (TYPE 1).
- Endless tapes cannot be used.
- Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Fast forward and rewind
Press the gor hbutton. “a” or “b” blinks. When the
desired location has been reached, press the nbutton.
Before use
When the unit is shipped from the factory, its AM frequency band is set
as “522 - 1710 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to “520 - 1710 kHz (in 10 kHz steps)” as follows.
1. Press the TUNER/BAND button to select “AM”.
2. While pressing the MEMORY button on the front panel, press the
TUNER/BAND button on the front panel.
To return the original setting, repeat steps above.
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
Automatic/Manual tuning
1. Press the TUNER/BAND button to select FM or AM.
- “TUNER” is selected automatically. “TUNER” appears on the
display, then “TUNER” is replaced by the tuner mode display.
2. Automatic tuning
Press the TU – or + TU button for at least 1 second to tune in a station.
The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the TU – or + TU button briefly until the desired frequency is
displayed.
To preset stations
Up to 24 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic presetting (APT)
1. Press the TUNER/BAND button to select FM or AM.
2. Press the MEMORY button for at least 3 seconds. “PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations for FM, 12 stations for AM have been preset or the
high end of the band is reached, automatic presetting stops.
“PROG.” disappears and the previous received station is heard.
3. To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will
be cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “Automatic/
Manual tuning”.
2. Press the MEMORY button.
3. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the channel num-
ber to be preset.
4. Press the MEMORY button.
- In this example, “103.25 MHz” FM station is preset on FM
channel 9.
- The number buttons on the remote control can be used to pre-
set the station directly. In this example, press 0, then 9 after
the step 2 above.
Note:
If the next step is not taken within 10 seconds while performing
steps 2 - 4, “PROG.” disappears and the preset operation is
cancelled. Press the MEMORY button to continue.
5. Repeat steps above to add more preset stations.
- When presetting a new station, the previous preset station is
cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the desired chan-
nel number. The selected channel number appears briefly.
- The number buttons on the remote control can also be used.
Press two number buttons within 2 seconds.
Preset scan tuning
1. Press the TUNER/BAND button to select AM or FM.
2. Press the PRESET – or PRESET + button (or the PRESET button
on the remote control) for at least 1 second.
- The channel number blinks.
- The preset stations are selected in sequence for approxi-
mately 5 seconds each.
3. Press the PRESET - or PRESET + button (or the PRESET button
bon the remote control) when the desired station has been selected.
Preset scanning will stop.

6. Press the nbutton to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the nbutton and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the gor hbutton, then press the
ibutton.
Using the remote control
Press two number buttons within 4 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the ibutton. “ A” blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the gbutton
repeatedly until “6” appears (in the track section) on the display. To skip
back to track 3 while track 6 is playing, press the hbutton
repeatedly until “3” appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the gor hbutton is pressed during play, the player will
search at high speed in the forward or reverse direction while the button
is being pressed. When the button is released, normal play will continue.
Random play (Remote Control only)
Press the RANDOM button to begin random play. The player will
automatically select and play tracks on the disc at random. “RANDOM”
appears on the display.
- Random play will not function during programmed play.
Repeat play (Remote Control only)
Press the REPEAT button before or during play. The player will play all
the tracks or all the programmed tracks repeatedly. “REPEAT” appears
on the display. To cancel repeat play, press the REPEAT button again.
“REPEAT” disappears.
PROGRAMMED PLAY
Up to 24 tracks on a disc can be programmed for play in any order.
- First, select “CD” function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
CD PLAY
Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
If disc is loaded, you can turn the unit on and begin play immediately
by pressing the ibutton.
1. Press the FUNCTION button to select “CD” function. “CD” appears
on the display, then “CD” is replaced by the CD mode display.
2. Press the qOPEN/CLOSE button to open the CD compartment lid
“OPEN” appears.
3. Place the disc with the label
facing up on the disc turntable.
(Place only one disc at a time.)
4. Press the qOPEN/CLOSE
button again to close the CD
compartment lid. “CLOSE” ap-
pears briefly then the total num-
ber of tracks and total playing
time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, “NO DISC” appears. If this occurs, load the
disc correctly or replace the damaged disc.
5. Press the ibutton. Play
starts from the first track.
The current track number and
elapsed playing time are
displayed.
1. Press the MEMORY button.
2. Select a track by using the
gor hbutton.
- The number buttons on the
remote control can also be
used.
3. Press the MEMORY button.
4. Repeat steps 2-3 to programme
additional tracks.
5. Press the ibutton to start
programmed play.
When all programmed tracks
have played, the player stops
automatically. “0 0.00” appears
on the display.
- The programme contents are retained in memory.
- Any attempt to programme more than 24 tracks will result in “FULL”
being displayed and discontinuation of the programming.
- To cancel programmed play, press the nbutton twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the
programmed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until
“- - - - . - -” is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-6-
-5-
ADJUSTING THE CLOCK (Main unit only)
NOTE:
When the unit is first connected to the AC power line, the clock display
blinks on the display.
Example: To set “PM 6:30”,
First, press the z/ON button to turn the power off. Only the clock display
blinks.
1. Press the CLOCK/TIMER for at least 2 seconds. “ ” blinks on the
display.
2. Press the MEMORY button.
The hours display blinks.
3. Turn the VOLUME control to set the “hours”.
4. Press the MEMORY button.
The minutes display blinks.
5. Turn the VOLUME control to set the “minutes”.
6. Press the MEMORY button. The clock starts.
- The time can be set accurately by pressing the MEMORY button
when a time signal is heard.
- To display the clock during operation, press the CLOCK/TIMER
button briefly. After a few seconds, the original display returns
- If a power failure occurs or the mains lead is disconnected, the clock
display blinks. Reset the time again.
Changing the clock to the 24-hour display
1. Press the z/ON button to turn the power off, and present time
display.
2. While clock is displaying, press the MEMORY button and hold it,
then press the ibutton.
Example: PM 1:00 v13:00
To return the original setting, repeat steps above.
BEFORE OPERATION
Turning the power on and off
Press the z/ON button. The display lights and “WELCOME” appears
briefly.
To turn the power off, press the z/ON button again. “GOODBYE”
appears briefly and the clock display remains lit.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the selected function is set.
CD section i
qOPEN/CLOSE
Deck section b, a
Tuner section TUNER/BAND
Remote control i, OPEN/CLOSE, b, a, TUNER/BAND,
VIDEO
Selecting the function
Press the FUNCTION button to select the desired function. Each time
the button is pressed, the display changes as follows:
CD vTAPE vTUNER vVIDEO:AUX vCD v. . .
The function is automatically selected when CD play or tape playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
- When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Turn the VOLUME control, or press the + or – VOLUME button on the
remote control. The volume level appears by numbers (VOL 0 ~ VOL
MAX) and bar-graph on the display.
Surround sound system
Press the SURROUND button. “SURROUND” appears on the display
and a “wide” effect is created.
Bass expander system
Press the BASSXPANDER button to enhance the bass sound. “BASS”
appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
Selecting the display backlight colour
The display has three colours of the backlight (Amber, Purple, Blue).
Press the DISPLAY button to select the desired display backlight colour.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the RESET button (rear of the unit) for at least 30 seconds.
3. Connect the mains lead.
4. Resume the operation.
15˚15˚
REMOTE CONTROL
Controls
-4-
1. Power button (z/ON)
2. Open/Close button for CD compartment lid (OPEN/CLOSE)
3. Number buttons (1-9, 0)
4. Memory button (MEMORY)
5. Tape deck controls
r: Record muting button
m: Record/Record pause button
d, c: Fast forward/Rewind buttons
b: Reverse play button
a: Forward play button
n: Stop button
6. CD player controls
i: Play/Pause button
n: Stop button
RANDOM: Random play button
REPEAT: Repeat button
7. FM mode button (FM MODE)
8. Sound preset button (SOUND PRESET)
9. Tuning buttons (TUNING +, –, f, e)
(These buttons can also be used as CD playing tracks skip and
search button)
10. Tuner function/Band select button (TUNER/BAND)
11. Volume buttons (VOLUME +, –)
12. Preset tuning button (PRESET)
13. Video function button (VIDEO)
14. Sleep button (SLEEP)
Number buttons (1 - 9, 0)
These buttons are used to select the track numbers on a disc or preset
radio stations.
If the function is “CD”, the buttons select the track numbers on a disc.
If the function is “TUNER”, the buttons select preset radio stations.
With any other function, the buttons will not function.
- Two buttons must always be pressed.
Example:
To select No. 3, press 0, then 3.
To select No. 10, press 1, then 0.
To select No. 25, press 2, then 5.
Inserting batteries
12
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range
The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.
Remote sensor
Within approx.
7 meters
Two R03/AAA batteries
(not supplied)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CONTROLS
General
1. Power button (z/ON)
2. Display
3. Volume control (VOLUME)
4. Clock/Timer button (CLOCK/TIMER)
5. Memory button (MEMORY)
6. Bass expander button (BASSXPANDER)
7. Surround button (SURROUND)
8. Sound preset button (SOUND PRESET)
9. Headphones socket (PHONES)
10. Remote sensor (IR)
11. Function button (FUNCTION)
12. Display backlight colour select button (DISPLAY)
CD player/Tuner
1. CD compartment
2. Open/Close button for CD compartment lid (qOPEN/CLOSE)
3. Tuning buttons (TU –, +TU)
4. Stop button ( n)
5. Skip/Search/Preset tuning buttons
(h/PRESET –, g/PRESET +)
6. Play/Pause button ( i)
7. FM mode button (FM MODE)
8. Tuner function/Band select button (TUNER/BAND)
Cassette deck
1. Stop button ( n)
2. Fast forward/Rewind buttons
(h/PRESET –, g/PRESET +)
3. Forward play button ( a)
4. Cassette holder
5. Reverse mode button (U)
6. Record/Record pause button ( j)
7. Reverse play button ( b)
-3-
4
6
5
7
8
123
9
11
10
12
7
8
6
1
5
4
2
3
7
5
6
4
1
2
3
12
-2-
Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when the
z/ON button is set to the zposition.
Speakers
Connect the connector of the left speaker lead to the “L” SPEAKERS
socket and the connector of the right speaker lead to the “R” socket.
If you have difficulty inserting the speaker lead connector, turn it over and
reinsert it.
FM aerials
The FM indoor aerials is sufficient to receive most local FM broadcasts
and should be connected to the FM 75Ωterminal. Extend the aerial wire
as straight as possible and, while listening to the sound from the system,
secure it in a position which yields minimal distortion and noise.
In fringe areas or where receptions is distorted or noisy an external aerial
(not supplied) should be connected instead of the simple indoor aerial.
Consult your dealer.
AM loop aerial
Assemble the loop aerial as shown in figure.
CONNECTIONS
Unwind the aerial wires, then connect them
to the AM LOOP terminals. Place the loop
aerial in a position which yields the best
AM reception, or attach it to a wall or other
surface as shown in figure.
Note:
To minimize noise, the speaker, mains
and any other leads should not come close
to the FM indoor or outdoor aerial lead and
AM loop aerial. Do not place the aerial
leads close to the system. Screws (not supplied)
Video/Auxiliary equipment
Connect audio leads (not supplied) from the audio output sockets of a
video/auxiliary equipment to the VIDEO (AUDIO) sockets.
Subwoofer output socket (SUB WOOFER)
Connect the amplified subwoofer (not supplied) to the SUB WOOFER
socket.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
12
FM outdoor
aerial
AM loop aerial
FM indoor aerial
R ch Speaker L ch Speaker
Video/Auxiliary
equipment
To an AC outlet
Amplifies subwoofer
(not supplied)
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large
output from the amplifier which could damage your speakers.
PRECAUTIONS
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN
THE OPERATING INSTRUCTIONS MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED PERSONNEL.
-1-
- Sudden changes in the ambient temperature may cause condensa-
tion to form on the optical lens inside the unit. If this happens, take
out the disc, leave the unit for about 1 hour, and then proceed to
operate.
- The system’s speakers use powerful magnets. Do not place
timepieces, credit cards, cassette tapes or video tapes, etc. near the
speakers.
- Do not install this equipment in a confined space, such as a book
case or built in cabinet.
- No objects filled with liquids, such as vases, shall be placed on the
apparatus.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE
FOR STRÅLING.
VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.
VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN
DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.
VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

6. Press the nbutton to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the nbutton and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the gor hbutton, then press the
ibutton.
Using the remote control
Press two number buttons within 4 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the ibutton. “ A” blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the gbutton
repeatedly until “6” appears (in the track section) on the display. To skip
back to track 3 while track 6 is playing, press the hbutton
repeatedly until “3” appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the gor hbutton is pressed during play, the player will
search at high speed in the forward or reverse direction while the button
is being pressed. When the button is released, normal play will continue.
Random play (Remote Control only)
Press the RANDOM button to begin random play. The player will
automatically select and play tracks on the disc at random. “RANDOM”
appears on the display.
- Random play will not function during programmed play.
Repeat play (Remote Control only)
Press the REPEAT button before or during play. The player will play all
the tracks or all the programmed tracks repeatedly. “REPEAT” appears
on the display. To cancel repeat play, press the REPEAT button again.
“REPEAT” disappears.
PROGRAMMED PLAY
Up to 24 tracks on a disc can be programmed for play in any order.
- First, select “CD” function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
CD PLAY
Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
If disc is loaded, you can turn the unit on and begin play immediately
by pressing the ibutton.
1. Press the FUNCTION button to select “CD” function. “CD” appears
on the display, then “CD” is replaced by the CD mode display.
2. Press the qOPEN/CLOSE button to open the CD compartment lid
“OPEN” appears.
3. Place the disc with the label
facing up on the disc turntable.
(Place only one disc at a time.)
4. Press the qOPEN/CLOSE
button again to close the CD
compartment lid. “CLOSE” ap-
pears briefly then the total num-
ber of tracks and total playing
time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, “NO DISC” appears. If this occurs, load the
disc correctly or replace the damaged disc.
5. Press the ibutton. Play
starts from the first track.
The current track number and
elapsed playing time are
displayed.
1. Press the MEMORY button.
2. Select a track by using the
gor hbutton.
- The number buttons on the
remote control can also be
used.
3. Press the MEMORY button.
4. Repeat steps 2-3 to programme
additional tracks.
5. Press the ibutton to start
programmed play.
When all programmed tracks
have played, the player stops
automatically. “0 0.00” appears
on the display.
- The programme contents are retained in memory.
- Any attempt to programme more than 24 tracks will result in “FULL”
being displayed and discontinuation of the programming.
- To cancel programmed play, press the nbutton twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the
programmed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until
“- - - - . - -” is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-6-
-5-
ADJUSTING THE CLOCK (Main unit only)
NOTE:
When the unit is first connected to the AC power line, the clock display
blinks on the display.
Example: To set “PM 6:30”,
First, press the z/ON button to turn the power off. Only the clock display
blinks.
1. Press the CLOCK/TIMER for at least 2 seconds. “ ” blinks on the
display.
2. Press the MEMORY button.
The hours display blinks.
3. Turn the VOLUME control to set the “hours”.
4. Press the MEMORY button.
The minutes display blinks.
5. Turn the VOLUME control to set the “minutes”.
6. Press the MEMORY button. The clock starts.
- The time can be set accurately by pressing the MEMORY button
when a time signal is heard.
- To display the clock during operation, press the CLOCK/TIMER
button briefly. After a few seconds, the original display returns
- If a power failure occurs or the mains lead is disconnected, the clock
display blinks. Reset the time again.
Changing the clock to the 24-hour display
1. Press the z/ON button to turn the power off, and present time
display.
2. While clock is displaying, press the MEMORY button and hold it,
then press the ibutton.
Example: PM 1:00 v13:00
To return the original setting, repeat steps above.
BEFORE OPERATION
Turning the power on and off
Press the z/ON button. The display lights and “WELCOME” appears
briefly.
To turn the power off, press the z/ON button again. “GOODBYE”
appears briefly and the clock display remains lit.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the selected function is set.
CD section i
qOPEN/CLOSE
Deck section b, a
Tuner section TUNER/BAND
Remote control i, OPEN/CLOSE, b, a, TUNER/BAND,
VIDEO
Selecting the function
Press the FUNCTION button to select the desired function. Each time
the button is pressed, the display changes as follows:
CD vTAPE vTUNER vVIDEO:AUX vCD v. . .
The function is automatically selected when CD play or tape playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
- When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Turn the VOLUME control, or press the + or – VOLUME button on the
remote control. The volume level appears by numbers (VOL 0 ~ VOL
MAX) and bar-graph on the display.
Surround sound system
Press the SURROUND button. “SURROUND” appears on the display
and a “wide” effect is created.
Bass expander system
Press the BASSXPANDER button to enhance the bass sound. “BASS”
appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
Selecting the display backlight colour
The display has three colours of the backlight (Amber, Purple, Blue).
Press the DISPLAY button to select the desired display backlight colour.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the RESET button (rear of the unit) for at least 30 seconds.
3. Connect the mains lead.
4. Resume the operation.
15˚15˚
REMOTE CONTROL
Controls
-4-
1. Power button (z/ON)
2. Open/Close button for CD compartment lid (OPEN/CLOSE)
3. Number buttons (1-9, 0)
4. Memory button (MEMORY)
5. Tape deck controls
r: Record muting button
m: Record/Record pause button
d, c: Fast forward/Rewind buttons
b: Reverse play button
a: Forward play button
n: Stop button
6. CD player controls
i: Play/Pause button
n: Stop button
RANDOM: Random play button
REPEAT: Repeat button
7. FM mode button (FM MODE)
8. Sound preset button (SOUND PRESET)
9. Tuning buttons (TUNING +, –, f, e)
(These buttons can also be used as CD playing tracks skip and
search button)
10. Tuner function/Band select button (TUNER/BAND)
11. Volume buttons (VOLUME +, –)
12. Preset tuning button (PRESET)
13. Video function button (VIDEO)
14. Sleep button (SLEEP)
Number buttons (1 - 9, 0)
These buttons are used to select the track numbers on a disc or preset
radio stations.
If the function is “CD”, the buttons select the track numbers on a disc.
If the function is “TUNER”, the buttons select preset radio stations.
With any other function, the buttons will not function.
- Two buttons must always be pressed.
Example:
To select No. 3, press 0, then 3.
To select No. 10, press 1, then 0.
To select No. 25, press 2, then 5.
Inserting batteries
12
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range
The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.
Remote sensor
Within approx.
7 meters
Two R03/AAA batteries
(not supplied)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CONTROLS
General
1. Power button (z/ON)
2. Display
3. Volume control (VOLUME)
4. Clock/Timer button (CLOCK/TIMER)
5. Memory button (MEMORY)
6. Bass expander button (BASSXPANDER)
7. Surround button (SURROUND)
8. Sound preset button (SOUND PRESET)
9. Headphones socket (PHONES)
10. Remote sensor (IR)
11. Function button (FUNCTION)
12. Display backlight colour select button (DISPLAY)
CD player/Tuner
1. CD compartment
2. Open/Close button for CD compartment lid (qOPEN/CLOSE)
3. Tuning buttons (TU –, +TU)
4. Stop button ( n)
5. Skip/Search/Preset tuning buttons
(h/PRESET –, g/PRESET +)
6. Play/Pause button ( i)
7. FM mode button (FM MODE)
8. Tuner function/Band select button (TUNER/BAND)
Cassette deck
1. Stop button ( n)
2. Fast forward/Rewind buttons
(h/PRESET –, g/PRESET +)
3. Forward play button ( a)
4. Cassette holder
5. Reverse mode button (U)
6. Record/Record pause button ( j)
7. Reverse play button ( b)
-3-
4
6
5
7
8
123
9
11
10
12
7
8
6
1
5
4
2
3
7
5
6
4
1
2
3
12
-2-
Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when the
z/ON button is set to the zposition.
Speakers
Connect the connector of the left speaker lead to the “L” SPEAKERS
socket and the connector of the right speaker lead to the “R” socket.
If you have difficulty inserting the speaker lead connector, turn it over and
reinsert it.
FM aerials
The FM indoor aerials is sufficient to receive most local FM broadcasts
and should be connected to the FM 75Ωterminal. Extend the aerial wire
as straight as possible and, while listening to the sound from the system,
secure it in a position which yields minimal distortion and noise.
In fringe areas or where receptions is distorted or noisy an external aerial
(not supplied) should be connected instead of the simple indoor aerial.
Consult your dealer.
AM loop aerial
Assemble the loop aerial as shown in figure.
CONNECTIONS
Unwind the aerial wires, then connect them
to the AM LOOP terminals. Place the loop
aerial in a position which yields the best
AM reception, or attach it to a wall or other
surface as shown in figure.
Note:
To minimize noise, the speaker, mains
and any other leads should not come close
to the FM indoor or outdoor aerial lead and
AM loop aerial. Do not place the aerial
leads close to the system. Screws (not supplied)
Video/Auxiliary equipment
Connect audio leads (not supplied) from the audio output sockets of a
video/auxiliary equipment to the VIDEO (AUDIO) sockets.
Subwoofer output socket (SUB WOOFER)
Connect the amplified subwoofer (not supplied) to the SUB WOOFER
socket.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
12
FM outdoor
aerial
AM loop aerial
FM indoor aerial
R ch Speaker L ch Speaker
Video/Auxiliary
equipment
To an AC outlet
Amplifies subwoofer
(not supplied)
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large
output from the amplifier which could damage your speakers.
PRECAUTIONS
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN
THE OPERATING INSTRUCTIONS MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED PERSONNEL.
-1-
- Sudden changes in the ambient temperature may cause condensa-
tion to form on the optical lens inside the unit. If this happens, take
out the disc, leave the unit for about 1 hour, and then proceed to
operate.
- The system’s speakers use powerful magnets. Do not place
timepieces, credit cards, cassette tapes or video tapes, etc. near the
speakers.
- Do not install this equipment in a confined space, such as a book
case or built in cabinet.
- No objects filled with liquids, such as vases, shall be placed on the
apparatus.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE
FOR STRÅLING.
VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.
VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN
DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.
VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

6. Press the nbutton to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the nbutton and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the gor hbutton, then press the
ibutton.
Using the remote control
Press two number buttons within 4 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the ibutton. “ A” blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the gbutton
repeatedly until “6” appears (in the track section) on the display. To skip
back to track 3 while track 6 is playing, press the hbutton
repeatedly until “3” appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the gor hbutton is pressed during play, the player will
search at high speed in the forward or reverse direction while the button
is being pressed. When the button is released, normal play will continue.
Random play (Remote Control only)
Press the RANDOM button to begin random play. The player will
automatically select and play tracks on the disc at random. “RANDOM”
appears on the display.
- Random play will not function during programmed play.
Repeat play (Remote Control only)
Press the REPEAT button before or during play. The player will play all
the tracks or all the programmed tracks repeatedly. “REPEAT” appears
on the display. To cancel repeat play, press the REPEAT button again.
“REPEAT” disappears.
PROGRAMMED PLAY
Up to 24 tracks on a disc can be programmed for play in any order.
- First, select “CD” function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
CD PLAY
Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
If disc is loaded, you can turn the unit on and begin play immediately
by pressing the ibutton.
1. Press the FUNCTION button to select “CD” function. “CD” appears
on the display, then “CD” is replaced by the CD mode display.
2. Press the qOPEN/CLOSE button to open the CD compartment lid
“OPEN” appears.
3. Place the disc with the label
facing up on the disc turntable.
(Place only one disc at a time.)
4. Press the qOPEN/CLOSE
button again to close the CD
compartment lid. “CLOSE” ap-
pears briefly then the total num-
ber of tracks and total playing
time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, “NO DISC” appears. If this occurs, load the
disc correctly or replace the damaged disc.
5. Press the ibutton. Play
starts from the first track.
The current track number and
elapsed playing time are
displayed.
1. Press the MEMORY button.
2. Select a track by using the
gor hbutton.
- The number buttons on the
remote control can also be
used.
3. Press the MEMORY button.
4. Repeat steps 2-3 to programme
additional tracks.
5. Press the ibutton to start
programmed play.
When all programmed tracks
have played, the player stops
automatically. “0 0.00” appears
on the display.
- The programme contents are retained in memory.
- Any attempt to programme more than 24 tracks will result in “FULL”
being displayed and discontinuation of the programming.
- To cancel programmed play, press the nbutton twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the
programmed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until
“- - - - . - -” is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-6-
-5-
ADJUSTING THE CLOCK (Main unit only)
NOTE:
When the unit is first connected to the AC power line, the clock display
blinks on the display.
Example: To set “PM 6:30”,
First, press the z/ON button to turn the power off. Only the clock display
blinks.
1. Press the CLOCK/TIMER for at least 2 seconds. “ ” blinks on the
display.
2. Press the MEMORY button.
The hours display blinks.
3. Turn the VOLUME control to set the “hours”.
4. Press the MEMORY button.
The minutes display blinks.
5. Turn the VOLUME control to set the “minutes”.
6. Press the MEMORY button. The clock starts.
- The time can be set accurately by pressing the MEMORY button
when a time signal is heard.
- To display the clock during operation, press the CLOCK/TIMER
button briefly. After a few seconds, the original display returns
- If a power failure occurs or the mains lead is disconnected, the clock
display blinks. Reset the time again.
Changing the clock to the 24-hour display
1. Press the z/ON button to turn the power off, and present time
display.
2. While clock is displaying, press the MEMORY button and hold it,
then press the ibutton.
Example: PM 1:00 v13:00
To return the original setting, repeat steps above.
BEFORE OPERATION
Turning the power on and off
Press the z/ON button. The display lights and “WELCOME” appears
briefly.
To turn the power off, press the z/ON button again. “GOODBYE”
appears briefly and the clock display remains lit.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the selected function is set.
CD section i
qOPEN/CLOSE
Deck section b, a
Tuner section TUNER/BAND
Remote control i, OPEN/CLOSE, b, a, TUNER/BAND,
VIDEO
Selecting the function
Press the FUNCTION button to select the desired function. Each time
the button is pressed, the display changes as follows:
CD vTAPE vTUNER vVIDEO:AUX vCD v. . .
The function is automatically selected when CD play or tape playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
- When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Turn the VOLUME control, or press the + or – VOLUME button on the
remote control. The volume level appears by numbers (VOL 0 ~ VOL
MAX) and bar-graph on the display.
Surround sound system
Press the SURROUND button. “SURROUND” appears on the display
and a “wide” effect is created.
Bass expander system
Press the BASSXPANDER button to enhance the bass sound. “BASS”
appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
Selecting the display backlight colour
The display has three colours of the backlight (Amber, Purple, Blue).
Press the DISPLAY button to select the desired display backlight colour.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the RESET button (rear of the unit) for at least 30 seconds.
3. Connect the mains lead.
4. Resume the operation.
15˚15˚
REMOTE CONTROL
Controls
-4-
1. Power button (z/ON)
2. Open/Close button for CD compartment lid (OPEN/CLOSE)
3. Number buttons (1-9, 0)
4. Memory button (MEMORY)
5. Tape deck controls
r: Record muting button
m: Record/Record pause button
d, c: Fast forward/Rewind buttons
b: Reverse play button
a: Forward play button
n: Stop button
6. CD player controls
i: Play/Pause button
n: Stop button
RANDOM: Random play button
REPEAT: Repeat button
7. FM mode button (FM MODE)
8. Sound preset button (SOUND PRESET)
9. Tuning buttons (TUNING +, –, f, e)
(These buttons can also be used as CD playing tracks skip and
search button)
10. Tuner function/Band select button (TUNER/BAND)
11. Volume buttons (VOLUME +, –)
12. Preset tuning button (PRESET)
13. Video function button (VIDEO)
14. Sleep button (SLEEP)
Number buttons (1 - 9, 0)
These buttons are used to select the track numbers on a disc or preset
radio stations.
If the function is “CD”, the buttons select the track numbers on a disc.
If the function is “TUNER”, the buttons select preset radio stations.
With any other function, the buttons will not function.
- Two buttons must always be pressed.
Example:
To select No. 3, press 0, then 3.
To select No. 10, press 1, then 0.
To select No. 25, press 2, then 5.
Inserting batteries
12
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range
The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.
Remote sensor
Within approx.
7 meters
Two R03/AAA batteries
(not supplied)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CONTROLS
General
1. Power button (z/ON)
2. Display
3. Volume control (VOLUME)
4. Clock/Timer button (CLOCK/TIMER)
5. Memory button (MEMORY)
6. Bass expander button (BASSXPANDER)
7. Surround button (SURROUND)
8. Sound preset button (SOUND PRESET)
9. Headphones socket (PHONES)
10. Remote sensor (IR)
11. Function button (FUNCTION)
12. Display backlight colour select button (DISPLAY)
CD player/Tuner
1. CD compartment
2. Open/Close button for CD compartment lid (qOPEN/CLOSE)
3. Tuning buttons (TU –, +TU)
4. Stop button ( n)
5. Skip/Search/Preset tuning buttons
(h/PRESET –, g/PRESET +)
6. Play/Pause button ( i)
7. FM mode button (FM MODE)
8. Tuner function/Band select button (TUNER/BAND)
Cassette deck
1. Stop button ( n)
2. Fast forward/Rewind buttons
(h/PRESET –, g/PRESET +)
3. Forward play button ( a)
4. Cassette holder
5. Reverse mode button (U)
6. Record/Record pause button ( j)
7. Reverse play button ( b)
-3-
4
6
5
7
8
123
9
11
10
12
7
8
6
1
5
4
2
3
7
5
6
4
1
2
3
12
-2-
Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when the
z/ON button is set to the zposition.
Speakers
Connect the connector of the left speaker lead to the “L” SPEAKERS
socket and the connector of the right speaker lead to the “R” socket.
If you have difficulty inserting the speaker lead connector, turn it over and
reinsert it.
FM aerials
The FM indoor aerials is sufficient to receive most local FM broadcasts
and should be connected to the FM 75Ωterminal. Extend the aerial wire
as straight as possible and, while listening to the sound from the system,
secure it in a position which yields minimal distortion and noise.
In fringe areas or where receptions is distorted or noisy an external aerial
(not supplied) should be connected instead of the simple indoor aerial.
Consult your dealer.
AM loop aerial
Assemble the loop aerial as shown in figure.
CONNECTIONS
Unwind the aerial wires, then connect them
to the AM LOOP terminals. Place the loop
aerial in a position which yields the best
AM reception, or attach it to a wall or other
surface as shown in figure.
Note:
To minimize noise, the speaker, mains
and any other leads should not come close
to the FM indoor or outdoor aerial lead and
AM loop aerial. Do not place the aerial
leads close to the system. Screws (not supplied)
Video/Auxiliary equipment
Connect audio leads (not supplied) from the audio output sockets of a
video/auxiliary equipment to the VIDEO (AUDIO) sockets.
Subwoofer output socket (SUB WOOFER)
Connect the amplified subwoofer (not supplied) to the SUB WOOFER
socket.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
12
FM outdoor
aerial
AM loop aerial
FM indoor aerial
R ch Speaker L ch Speaker
Video/Auxiliary
equipment
To an AC outlet
Amplifies subwoofer
(not supplied)
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large
output from the amplifier which could damage your speakers.
PRECAUTIONS
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN
THE OPERATING INSTRUCTIONS MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED PERSONNEL.
-1-
- Sudden changes in the ambient temperature may cause condensa-
tion to form on the optical lens inside the unit. If this happens, take
out the disc, leave the unit for about 1 hour, and then proceed to
operate.
- The system’s speakers use powerful magnets. Do not place
timepieces, credit cards, cassette tapes or video tapes, etc. near the
speakers.
- Do not install this equipment in a confined space, such as a book
case or built in cabinet.
- No objects filled with liquids, such as vases, shall be placed on the
apparatus.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE
FOR STRÅLING.
VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.
VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN
DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.
VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

6. Press the nbutton to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the nbutton and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the gor hbutton, then press the
ibutton.
Using the remote control
Press two number buttons within 4 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the ibutton. “ A” blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the gbutton
repeatedly until “6” appears (in the track section) on the display. To skip
back to track 3 while track 6 is playing, press the hbutton
repeatedly until “3” appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the gor hbutton is pressed during play, the player will
search at high speed in the forward or reverse direction while the button
is being pressed. When the button is released, normal play will continue.
Random play (Remote Control only)
Press the RANDOM button to begin random play. The player will
automatically select and play tracks on the disc at random. “RANDOM”
appears on the display.
- Random play will not function during programmed play.
Repeat play (Remote Control only)
Press the REPEAT button before or during play. The player will play all
the tracks or all the programmed tracks repeatedly. “REPEAT” appears
on the display. To cancel repeat play, press the REPEAT button again.
“REPEAT” disappears.
PROGRAMMED PLAY
Up to 24 tracks on a disc can be programmed for play in any order.
- First, select “CD” function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
CD PLAY
Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
If disc is loaded, you can turn the unit on and begin play immediately
by pressing the ibutton.
1. Press the FUNCTION button to select “CD” function. “CD” appears
on the display, then “CD” is replaced by the CD mode display.
2. Press the qOPEN/CLOSE button to open the CD compartment lid
“OPEN” appears.
3. Place the disc with the label
facing up on the disc turntable.
(Place only one disc at a time.)
4. Press the qOPEN/CLOSE
button again to close the CD
compartment lid. “CLOSE” ap-
pears briefly then the total num-
ber of tracks and total playing
time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, “NO DISC” appears. If this occurs, load the
disc correctly or replace the damaged disc.
5. Press the ibutton. Play
starts from the first track.
The current track number and
elapsed playing time are
displayed.
1. Press the MEMORY button.
2. Select a track by using the
gor hbutton.
- The number buttons on the
remote control can also be
used.
3. Press the MEMORY button.
4. Repeat steps 2-3 to programme
additional tracks.
5. Press the ibutton to start
programmed play.
When all programmed tracks
have played, the player stops
automatically. “0 0.00” appears
on the display.
- The programme contents are retained in memory.
- Any attempt to programme more than 24 tracks will result in “FULL”
being displayed and discontinuation of the programming.
- To cancel programmed play, press the nbutton twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the
programmed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until
“- - - - . - -” is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-6-
-5-
ADJUSTING THE CLOCK (Main unit only)
NOTE:
When the unit is first connected to the AC power line, the clock display
blinks on the display.
Example: To set “PM 6:30”,
First, press the z/ON button to turn the power off. Only the clock display
blinks.
1. Press the CLOCK/TIMER for at least 2 seconds. “ ” blinks on the
display.
2. Press the MEMORY button.
The hours display blinks.
3. Turn the VOLUME control to set the “hours”.
4. Press the MEMORY button.
The minutes display blinks.
5. Turn the VOLUME control to set the “minutes”.
6. Press the MEMORY button. The clock starts.
- The time can be set accurately by pressing the MEMORY button
when a time signal is heard.
- To display the clock during operation, press the CLOCK/TIMER
button briefly. After a few seconds, the original display returns
- If a power failure occurs or the mains lead is disconnected, the clock
display blinks. Reset the time again.
Changing the clock to the 24-hour display
1. Press the z/ON button to turn the power off, and present time
display.
2. While clock is displaying, press the MEMORY button and hold it,
then press the ibutton.
Example: PM 1:00 v13:00
To return the original setting, repeat steps above.
BEFORE OPERATION
Turning the power on and off
Press the z/ON button. The display lights and “WELCOME” appears
briefly.
To turn the power off, press the z/ON button again. “GOODBYE”
appears briefly and the clock display remains lit.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the selected function is set.
CD section i
qOPEN/CLOSE
Deck section b, a
Tuner section TUNER/BAND
Remote control i, OPEN/CLOSE, b, a, TUNER/BAND,
VIDEO
Selecting the function
Press the FUNCTION button to select the desired function. Each time
the button is pressed, the display changes as follows:
CD vTAPE vTUNER vVIDEO:AUX vCD v. . .
The function is automatically selected when CD play or tape playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
- When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Turn the VOLUME control, or press the + or – VOLUME button on the
remote control. The volume level appears by numbers (VOL 0 ~ VOL
MAX) and bar-graph on the display.
Surround sound system
Press the SURROUND button. “SURROUND” appears on the display
and a “wide” effect is created.
Bass expander system
Press the BASSXPANDER button to enhance the bass sound. “BASS”
appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
Selecting the display backlight colour
The display has three colours of the backlight (Amber, Purple, Blue).
Press the DISPLAY button to select the desired display backlight colour.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the RESET button (rear of the unit) for at least 30 seconds.
3. Connect the mains lead.
4. Resume the operation.
15˚15˚
REMOTE CONTROL
Controls
-4-
1. Power button (z/ON)
2. Open/Close button for CD compartment lid (OPEN/CLOSE)
3. Number buttons (1-9, 0)
4. Memory button (MEMORY)
5. Tape deck controls
r: Record muting button
m: Record/Record pause button
d, c: Fast forward/Rewind buttons
b: Reverse play button
a: Forward play button
n: Stop button
6. CD player controls
i: Play/Pause button
n: Stop button
RANDOM: Random play button
REPEAT: Repeat button
7. FM mode button (FM MODE)
8. Sound preset button (SOUND PRESET)
9. Tuning buttons (TUNING +, –, f, e)
(These buttons can also be used as CD playing tracks skip and
search button)
10. Tuner function/Band select button (TUNER/BAND)
11. Volume buttons (VOLUME +, –)
12. Preset tuning button (PRESET)
13. Video function button (VIDEO)
14. Sleep button (SLEEP)
Number buttons (1 - 9, 0)
These buttons are used to select the track numbers on a disc or preset
radio stations.
If the function is “CD”, the buttons select the track numbers on a disc.
If the function is “TUNER”, the buttons select preset radio stations.
With any other function, the buttons will not function.
- Two buttons must always be pressed.
Example:
To select No. 3, press 0, then 3.
To select No. 10, press 1, then 0.
To select No. 25, press 2, then 5.
Inserting batteries
12
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range
The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.
Remote sensor
Within approx.
7 meters
Two R03/AAA batteries
(not supplied)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CONTROLS
General
1. Power button (z/ON)
2. Display
3. Volume control (VOLUME)
4. Clock/Timer button (CLOCK/TIMER)
5. Memory button (MEMORY)
6. Bass expander button (BASSXPANDER)
7. Surround button (SURROUND)
8. Sound preset button (SOUND PRESET)
9. Headphones socket (PHONES)
10. Remote sensor (IR)
11. Function button (FUNCTION)
12. Display backlight colour select button (DISPLAY)
CD player/Tuner
1. CD compartment
2. Open/Close button for CD compartment lid (qOPEN/CLOSE)
3. Tuning buttons (TU –, +TU)
4. Stop button ( n)
5. Skip/Search/Preset tuning buttons
(h/PRESET –, g/PRESET +)
6. Play/Pause button ( i)
7. FM mode button (FM MODE)
8. Tuner function/Band select button (TUNER/BAND)
Cassette deck
1. Stop button ( n)
2. Fast forward/Rewind buttons
(h/PRESET –, g/PRESET +)
3. Forward play button ( a)
4. Cassette holder
5. Reverse mode button (U)
6. Record/Record pause button ( j)
7. Reverse play button ( b)
-3-
4
6
5
7
8
123
9
11
10
12
7
8
6
1
5
4
2
3
7
5
6
4
1
2
3
12
-2-
Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when the
z/ON button is set to the zposition.
Speakers
Connect the connector of the left speaker lead to the “L” SPEAKERS
socket and the connector of the right speaker lead to the “R” socket.
If you have difficulty inserting the speaker lead connector, turn it over and
reinsert it.
FM aerials
The FM indoor aerials is sufficient to receive most local FM broadcasts
and should be connected to the FM 75Ωterminal. Extend the aerial wire
as straight as possible and, while listening to the sound from the system,
secure it in a position which yields minimal distortion and noise.
In fringe areas or where receptions is distorted or noisy an external aerial
(not supplied) should be connected instead of the simple indoor aerial.
Consult your dealer.
AM loop aerial
Assemble the loop aerial as shown in figure.
CONNECTIONS
Unwind the aerial wires, then connect them
to the AM LOOP terminals. Place the loop
aerial in a position which yields the best
AM reception, or attach it to a wall or other
surface as shown in figure.
Note:
To minimize noise, the speaker, mains
and any other leads should not come close
to the FM indoor or outdoor aerial lead and
AM loop aerial. Do not place the aerial
leads close to the system. Screws (not supplied)
Video/Auxiliary equipment
Connect audio leads (not supplied) from the audio output sockets of a
video/auxiliary equipment to the VIDEO (AUDIO) sockets.
Subwoofer output socket (SUB WOOFER)
Connect the amplified subwoofer (not supplied) to the SUB WOOFER
socket.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
12
FM outdoor
aerial
AM loop aerial
FM indoor aerial
R ch Speaker L ch Speaker
Video/Auxiliary
equipment
To an AC outlet
Amplifies subwoofer
(not supplied)
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large
output from the amplifier which could damage your speakers.
PRECAUTIONS
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN
THE OPERATING INSTRUCTIONS MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED PERSONNEL.
-1-
- Sudden changes in the ambient temperature may cause condensa-
tion to form on the optical lens inside the unit. If this happens, take
out the disc, leave the unit for about 1 hour, and then proceed to
operate.
- The system’s speakers use powerful magnets. Do not place
timepieces, credit cards, cassette tapes or video tapes, etc. near the
speakers.
- Do not install this equipment in a confined space, such as a book
case or built in cabinet.
- No objects filled with liquids, such as vases, shall be placed on the
apparatus.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE
FOR STRÅLING.
VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.
VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN
DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.
VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

6. Press the nbutton to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the nbutton and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the gor hbutton, then press the
ibutton.
Using the remote control
Press two number buttons within 4 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the ibutton. “ A” blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the gbutton
repeatedly until “6” appears (in the track section) on the display. To skip
back to track 3 while track 6 is playing, press the hbutton
repeatedly until “3” appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the gor hbutton is pressed during play, the player will
search at high speed in the forward or reverse direction while the button
is being pressed. When the button is released, normal play will continue.
Random play (Remote Control only)
Press the RANDOM button to begin random play. The player will
automatically select and play tracks on the disc at random. “RANDOM”
appears on the display.
- Random play will not function during programmed play.
Repeat play (Remote Control only)
Press the REPEAT button before or during play. The player will play all
the tracks or all the programmed tracks repeatedly. “REPEAT” appears
on the display. To cancel repeat play, press the REPEAT button again.
“REPEAT” disappears.
PROGRAMMED PLAY
Up to 24 tracks on a disc can be programmed for play in any order.
- First, select “CD” function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
CD PLAY
Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
If disc is loaded, you can turn the unit on and begin play immediately
by pressing the ibutton.
1. Press the FUNCTION button to select “CD” function. “CD” appears
on the display, then “CD” is replaced by the CD mode display.
2. Press the qOPEN/CLOSE button to open the CD compartment lid
“OPEN” appears.
3. Place the disc with the label
facing up on the disc turntable.
(Place only one disc at a time.)
4. Press the qOPEN/CLOSE
button again to close the CD
compartment lid. “CLOSE” ap-
pears briefly then the total num-
ber of tracks and total playing
time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, “NO DISC” appears. If this occurs, load the
disc correctly or replace the damaged disc.
5. Press the ibutton. Play
starts from the first track.
The current track number and
elapsed playing time are
displayed.
1. Press the MEMORY button.
2. Select a track by using the
gor hbutton.
- The number buttons on the
remote control can also be
used.
3. Press the MEMORY button.
4. Repeat steps 2-3 to programme
additional tracks.
5. Press the ibutton to start
programmed play.
When all programmed tracks
have played, the player stops
automatically. “0 0.00” appears
on the display.
- The programme contents are retained in memory.
- Any attempt to programme more than 24 tracks will result in “FULL”
being displayed and discontinuation of the programming.
- To cancel programmed play, press the nbutton twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the
programmed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until
“- - - - . - -” is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-6-
-5-
ADJUSTING THE CLOCK (Main unit only)
NOTE:
When the unit is first connected to the AC power line, the clock display
blinks on the display.
Example: To set “PM 6:30”,
First, press the z/ON button to turn the power off. Only the clock display
blinks.
1. Press the CLOCK/TIMER for at least 2 seconds. “ ” blinks on the
display.
2. Press the MEMORY button.
The hours display blinks.
3. Turn the VOLUME control to set the “hours”.
4. Press the MEMORY button.
The minutes display blinks.
5. Turn the VOLUME control to set the “minutes”.
6. Press the MEMORY button. The clock starts.
- The time can be set accurately by pressing the MEMORY button
when a time signal is heard.
- To display the clock during operation, press the CLOCK/TIMER
button briefly. After a few seconds, the original display returns
- If a power failure occurs or the mains lead is disconnected, the clock
display blinks. Reset the time again.
Changing the clock to the 24-hour display
1. Press the z/ON button to turn the power off, and present time
display.
2. While clock is displaying, press the MEMORY button and hold it,
then press the ibutton.
Example: PM 1:00 v13:00
To return the original setting, repeat steps above.
BEFORE OPERATION
Turning the power on and off
Press the z/ON button. The display lights and “WELCOME” appears
briefly.
To turn the power off, press the z/ON button again. “GOODBYE”
appears briefly and the clock display remains lit.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the selected function is set.
CD section i
qOPEN/CLOSE
Deck section b, a
Tuner section TUNER/BAND
Remote control i, OPEN/CLOSE, b, a, TUNER/BAND,
VIDEO
Selecting the function
Press the FUNCTION button to select the desired function. Each time
the button is pressed, the display changes as follows:
CD vTAPE vTUNER vVIDEO:AUX vCD v. . .
The function is automatically selected when CD play or tape playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
- When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Turn the VOLUME control, or press the + or – VOLUME button on the
remote control. The volume level appears by numbers (VOL 0 ~ VOL
MAX) and bar-graph on the display.
Surround sound system
Press the SURROUND button. “SURROUND” appears on the display
and a “wide” effect is created.
Bass expander system
Press the BASSXPANDER button to enhance the bass sound. “BASS”
appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
Selecting the display backlight colour
The display has three colours of the backlight (Amber, Purple, Blue).
Press the DISPLAY button to select the desired display backlight colour.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the RESET button (rear of the unit) for at least 30 seconds.
3. Connect the mains lead.
4. Resume the operation.
15˚15˚
REMOTE CONTROL
Controls
-4-
1. Power button (z/ON)
2. Open/Close button for CD compartment lid (OPEN/CLOSE)
3. Number buttons (1-9, 0)
4. Memory button (MEMORY)
5. Tape deck controls
r: Record muting button
m: Record/Record pause button
d, c: Fast forward/Rewind buttons
b: Reverse play button
a: Forward play button
n: Stop button
6. CD player controls
i: Play/Pause button
n: Stop button
RANDOM: Random play button
REPEAT: Repeat button
7. FM mode button (FM MODE)
8. Sound preset button (SOUND PRESET)
9. Tuning buttons (TUNING +, –, f, e)
(These buttons can also be used as CD playing tracks skip and
search button)
10. Tuner function/Band select button (TUNER/BAND)
11. Volume buttons (VOLUME +, –)
12. Preset tuning button (PRESET)
13. Video function button (VIDEO)
14. Sleep button (SLEEP)
Number buttons (1 - 9, 0)
These buttons are used to select the track numbers on a disc or preset
radio stations.
If the function is “CD”, the buttons select the track numbers on a disc.
If the function is “TUNER”, the buttons select preset radio stations.
With any other function, the buttons will not function.
- Two buttons must always be pressed.
Example:
To select No. 3, press 0, then 3.
To select No. 10, press 1, then 0.
To select No. 25, press 2, then 5.
Inserting batteries
12
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range
The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.
Remote sensor
Within approx.
7 meters
Two R03/AAA batteries
(not supplied)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CONTROLS
General
1. Power button (z/ON)
2. Display
3. Volume control (VOLUME)
4. Clock/Timer button (CLOCK/TIMER)
5. Memory button (MEMORY)
6. Bass expander button (BASSXPANDER)
7. Surround button (SURROUND)
8. Sound preset button (SOUND PRESET)
9. Headphones socket (PHONES)
10. Remote sensor (IR)
11. Function button (FUNCTION)
12. Display backlight colour select button (DISPLAY)
CD player/Tuner
1. CD compartment
2. Open/Close button for CD compartment lid (qOPEN/CLOSE)
3. Tuning buttons (TU –, +TU)
4. Stop button ( n)
5. Skip/Search/Preset tuning buttons
(h/PRESET –, g/PRESET +)
6. Play/Pause button ( i)
7. FM mode button (FM MODE)
8. Tuner function/Band select button (TUNER/BAND)
Cassette deck
1. Stop button ( n)
2. Fast forward/Rewind buttons
(h/PRESET –, g/PRESET +)
3. Forward play button ( a)
4. Cassette holder
5. Reverse mode button (U)
6. Record/Record pause button ( j)
7. Reverse play button ( b)
-3-
4
6
5
7
8
123
9
11
10
12
7
8
6
1
5
4
2
3
7
5
6
4
1
2
3
12
-2-
Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when the
z/ON button is set to the zposition.
Speakers
Connect the connector of the left speaker lead to the “L” SPEAKERS
socket and the connector of the right speaker lead to the “R” socket.
If you have difficulty inserting the speaker lead connector, turn it over and
reinsert it.
FM aerials
The FM indoor aerials is sufficient to receive most local FM broadcasts
and should be connected to the FM 75Ωterminal. Extend the aerial wire
as straight as possible and, while listening to the sound from the system,
secure it in a position which yields minimal distortion and noise.
In fringe areas or where receptions is distorted or noisy an external aerial
(not supplied) should be connected instead of the simple indoor aerial.
Consult your dealer.
AM loop aerial
Assemble the loop aerial as shown in figure.
CONNECTIONS
Unwind the aerial wires, then connect them
to the AM LOOP terminals. Place the loop
aerial in a position which yields the best
AM reception, or attach it to a wall or other
surface as shown in figure.
Note:
To minimize noise, the speaker, mains
and any other leads should not come close
to the FM indoor or outdoor aerial lead and
AM loop aerial. Do not place the aerial
leads close to the system. Screws (not supplied)
Video/Auxiliary equipment
Connect audio leads (not supplied) from the audio output sockets of a
video/auxiliary equipment to the VIDEO (AUDIO) sockets.
Subwoofer output socket (SUB WOOFER)
Connect the amplified subwoofer (not supplied) to the SUB WOOFER
socket.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
12
FM outdoor
aerial
AM loop aerial
FM indoor aerial
R ch Speaker L ch Speaker
Video/Auxiliary
equipment
To an AC outlet
Amplifies subwoofer
(not supplied)
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large
output from the amplifier which could damage your speakers.
PRECAUTIONS
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN
THE OPERATING INSTRUCTIONS MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED PERSONNEL.
-1-
- Sudden changes in the ambient temperature may cause condensa-
tion to form on the optical lens inside the unit. If this happens, take
out the disc, leave the unit for about 1 hour, and then proceed to
operate.
- The system’s speakers use powerful magnets. Do not place
timepieces, credit cards, cassette tapes or video tapes, etc. near the
speakers.
- Do not install this equipment in a confined space, such as a book
case or built in cabinet.
- No objects filled with liquids, such as vases, shall be placed on the
apparatus.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE
FOR STRÅLING.
VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.
VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN
DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.
VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

6. Press the nbutton to end disc play.
When the last track has been played, the player stops automatically.
Note:
Always press the nbutton and wait for the disc to stop rotating before
opening the CD compartment.
Notes on handling compact discs
- Do not expose the disc to direct sunlight, high humidity or high
temperatures for extended periods of time.
- Discs should be returned to their cases after use.
- Do not apply paper or write anything on the disc surface.
- Handle the disc by its edge. Do not touch the playing surface (glossy
side).
- Fingerprints and dust should be carefully wiped off the playing
surface of the disc with a soft cloth.
Wipe in a straight motion from the centre to the outside of the disc.
- Never use chemicals such as record cleaning sprays, antistatic
sprays or fluids, benzene or thinner to clean compact discs.
To start play from the desired track
Select the track by using the gor hbutton, then press the
ibutton.
Using the remote control
Press two number buttons within 4 seconds. (Example: press 0, then 3.)
Temporarily stopping play
Press the ibutton. “ A” blinks on the display. To resume play, press
the button again.
Skip play
To skip to track 6 while track 3 is playing, press the gbutton
repeatedly until “6” appears (in the track section) on the display. To skip
back to track 3 while track 6 is playing, press the hbutton
repeatedly until “3” appears.
- The number buttons on the remote control can also be used for skip
play. To skip to track 6 while one track is playing, press 0, then 6.
Search (forward/reverse)
If the gor hbutton is pressed during play, the player will
search at high speed in the forward or reverse direction while the button
is being pressed. When the button is released, normal play will continue.
Random play (Remote Control only)
Press the RANDOM button to begin random play. The player will
automatically select and play tracks on the disc at random. “RANDOM”
appears on the display.
- Random play will not function during programmed play.
Repeat play (Remote Control only)
Press the REPEAT button before or during play. The player will play all
the tracks or all the programmed tracks repeatedly. “REPEAT” appears
on the display. To cancel repeat play, press the REPEAT button again.
“REPEAT” disappears.
PROGRAMMED PLAY
Up to 24 tracks on a disc can be programmed for play in any order.
- First, select “CD” function and load a disc that you want to programme.
- The tracks must be programmed in the stop mode.
- The same track can be programmed more than once.
CD PLAY
Use compact discs bearing the symbol shown. In
addition to conventional 12 cm CDs, this system
can be used to play 8 cm CDs without an adapter.
If disc is loaded, you can turn the unit on and begin play immediately
by pressing the ibutton.
1. Press the FUNCTION button to select “CD” function. “CD” appears
on the display, then “CD” is replaced by the CD mode display.
2. Press the qOPEN/CLOSE button to open the CD compartment lid
“OPEN” appears.
3. Place the disc with the label
facing up on the disc turntable.
(Place only one disc at a time.)
4. Press the qOPEN/CLOSE
button again to close the CD
compartment lid. “CLOSE” ap-
pears briefly then the total num-
ber of tracks and total playing
time on the disc appear.
Note:
If the disc is loaded with the label facing downward, or if a badly
scratched disc is loaded, “NO DISC” appears. If this occurs, load the
disc correctly or replace the damaged disc.
5. Press the ibutton. Play
starts from the first track.
The current track number and
elapsed playing time are
displayed.
1. Press the MEMORY button.
2. Select a track by using the
gor hbutton.
- The number buttons on the
remote control can also be
used.
3. Press the MEMORY button.
4. Repeat steps 2-3 to programme
additional tracks.
5. Press the ibutton to start
programmed play.
When all programmed tracks
have played, the player stops
automatically. “0 0.00” appears
on the display.
- The programme contents are retained in memory.
- Any attempt to programme more than 24 tracks will result in “FULL”
being displayed and discontinuation of the programming.
- To cancel programmed play, press the nbutton twice.
Checking the programme
Each time the MEMORY button is pressed in the stop mode, the
programmed details sequentially appear on the display.
Changing a programme
To add a new track to a programme:
1. In the stop mode, press the MEMORY button repeatedly until
“- - - - . - -” is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
To change a track:
1. In the stop mode, press the MEMORY button repeatedly until the
track number to be replaced is displayed.
2. Select a track as explained above.
3. Press the MEMORY button.
Note:
Programmed details cannot be partially deleted or inserted.
-6-
-5-
ADJUSTING THE CLOCK (Main unit only)
NOTE:
When the unit is first connected to the AC power line, the clock display
blinks on the display.
Example: To set “PM 6:30”,
First, press the z/ON button to turn the power off. Only the clock display
blinks.
1. Press the CLOCK/TIMER for at least 2 seconds. “ ” blinks on the
display.
2. Press the MEMORY button.
The hours display blinks.
3. Turn the VOLUME control to set the “hours”.
4. Press the MEMORY button.
The minutes display blinks.
5. Turn the VOLUME control to set the “minutes”.
6. Press the MEMORY button. The clock starts.
- The time can be set accurately by pressing the MEMORY button
when a time signal is heard.
- To display the clock during operation, press the CLOCK/TIMER
button briefly. After a few seconds, the original display returns
- If a power failure occurs or the mains lead is disconnected, the clock
display blinks. Reset the time again.
Changing the clock to the 24-hour display
1. Press the z/ON button to turn the power off, and present time
display.
2. While clock is displaying, press the MEMORY button and hold it,
then press the ibutton.
Example: PM 1:00 v13:00
To return the original setting, repeat steps above.
BEFORE OPERATION
Turning the power on and off
Press the z/ON button. The display lights and “WELCOME” appears
briefly.
To turn the power off, press the z/ON button again. “GOODBYE”
appears briefly and the clock display remains lit.
- When the mains lead is connected to the AC outlet, the unit will
respond to commands from the remote control.
Direct start function
If the following buttons are pressed when the unit is in standby, the
unit turns on automatically and the selected function is set.
CD section i
qOPEN/CLOSE
Deck section b, a
Tuner section TUNER/BAND
Remote control i, OPEN/CLOSE, b, a, TUNER/BAND,
VIDEO
Selecting the function
Press the FUNCTION button to select the desired function. Each time
the button is pressed, the display changes as follows:
CD vTAPE vTUNER vVIDEO:AUX vCD v. . .
The function is automatically selected when CD play or tape playback is
started or when the TUNER/BAND button has been pressed (except
during recording).
- When the function selection is changed, CD play or tape playback is
automatically stopped.
Adjusting the volume
Turn the VOLUME control, or press the + or – VOLUME button on the
remote control. The volume level appears by numbers (VOL 0 ~ VOL
MAX) and bar-graph on the display.
Surround sound system
Press the SURROUND button. “SURROUND” appears on the display
and a “wide” effect is created.
Bass expander system
Press the BASSXPANDER button to enhance the bass sound. “BASS”
appears on the display.
Selecting the sound mode
Press the SOUND PRESET button to select the sound mode matching
the music to be listened to.
POP: Pops, etc.
CLASSIC: Classical music, etc.
ROCK: Rock music, etc.
JAZZ: Jazz, etc.
Selecting the display backlight colour
The display has three colours of the backlight (Amber, Purple, Blue).
Press the DISPLAY button to select the desired display backlight colour.
WHAT TO DO IF ...
If the operation of the unit or display is not normal,
1. Disconnect the mains lead.
2. Press the RESET button (rear of the unit) for at least 30 seconds.
3. Connect the mains lead.
4. Resume the operation.
15˚15˚
REMOTE CONTROL
Controls
-4-
1. Power button (z/ON)
2. Open/Close button for CD compartment lid (OPEN/CLOSE)
3. Number buttons (1-9, 0)
4. Memory button (MEMORY)
5. Tape deck controls
r: Record muting button
m: Record/Record pause button
d, c: Fast forward/Rewind buttons
b: Reverse play button
a: Forward play button
n: Stop button
6. CD player controls
i: Play/Pause button
n: Stop button
RANDOM: Random play button
REPEAT: Repeat button
7. FM mode button (FM MODE)
8. Sound preset button (SOUND PRESET)
9. Tuning buttons (TUNING +, –, f, e)
(These buttons can also be used as CD playing tracks skip and
search button)
10. Tuner function/Band select button (TUNER/BAND)
11. Volume buttons (VOLUME +, –)
12. Preset tuning button (PRESET)
13. Video function button (VIDEO)
14. Sleep button (SLEEP)
Number buttons (1 - 9, 0)
These buttons are used to select the track numbers on a disc or preset
radio stations.
If the function is “CD”, the buttons select the track numbers on a disc.
If the function is “TUNER”, the buttons select preset radio stations.
With any other function, the buttons will not function.
- Two buttons must always be pressed.
Example:
To select No. 3, press 0, then 3.
To select No. 10, press 1, then 0.
To select No. 25, press 2, then 5.
Inserting batteries
12
Note:
Always remove batteries if the remote control is not to be used for a
month or more. Batteries left in the unit may leak and cause damage.
Remote control range
The buttons on the remote control perform similar functions to similarly
marked buttons on the front panel.
Remote sensor
Within approx.
7 meters
Two R03/AAA batteries
(not supplied)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
CONTROLS
General
1. Power button (z/ON)
2. Display
3. Volume control (VOLUME)
4. Clock/Timer button (CLOCK/TIMER)
5. Memory button (MEMORY)
6. Bass expander button (BASSXPANDER)
7. Surround button (SURROUND)
8. Sound preset button (SOUND PRESET)
9. Headphones socket (PHONES)
10. Remote sensor (IR)
11. Function button (FUNCTION)
12. Display backlight colour select button (DISPLAY)
CD player/Tuner
1. CD compartment
2. Open/Close button for CD compartment lid (qOPEN/CLOSE)
3. Tuning buttons (TU –, +TU)
4. Stop button ( n)
5. Skip/Search/Preset tuning buttons
(h/PRESET –, g/PRESET +)
6. Play/Pause button ( i)
7. FM mode button (FM MODE)
8. Tuner function/Band select button (TUNER/BAND)
Cassette deck
1. Stop button ( n)
2. Fast forward/Rewind buttons
(h/PRESET –, g/PRESET +)
3. Forward play button ( a)
4. Cassette holder
5. Reverse mode button (U)
6. Record/Record pause button ( j)
7. Reverse play button ( b)
-3-
4
6
5
7
8
123
9
11
10
12
7
8
6
1
5
4
2
3
7
5
6
4
1
2
3
12
-2-
Note:
- Do not connect the mains lead to an AC outlet until all connections
have been made.
- The system is not completely disconnected from the mains when the
z/ON button is set to the zposition.
Speakers
Connect the connector of the left speaker lead to the “L” SPEAKERS
socket and the connector of the right speaker lead to the “R” socket.
If you have difficulty inserting the speaker lead connector, turn it over and
reinsert it.
FM aerials
The FM indoor aerials is sufficient to receive most local FM broadcasts
and should be connected to the FM 75Ωterminal. Extend the aerial wire
as straight as possible and, while listening to the sound from the system,
secure it in a position which yields minimal distortion and noise.
In fringe areas or where receptions is distorted or noisy an external aerial
(not supplied) should be connected instead of the simple indoor aerial.
Consult your dealer.
AM loop aerial
Assemble the loop aerial as shown in figure.
CONNECTIONS
Unwind the aerial wires, then connect them
to the AM LOOP terminals. Place the loop
aerial in a position which yields the best
AM reception, or attach it to a wall or other
surface as shown in figure.
Note:
To minimize noise, the speaker, mains
and any other leads should not come close
to the FM indoor or outdoor aerial lead and
AM loop aerial. Do not place the aerial
leads close to the system. Screws (not supplied)
Video/Auxiliary equipment
Connect audio leads (not supplied) from the audio output sockets of a
video/auxiliary equipment to the VIDEO (AUDIO) sockets.
Subwoofer output socket (SUB WOOFER)
Connect the amplified subwoofer (not supplied) to the SUB WOOFER
socket.
Headphones
Connect stereo headphones (not supplied) to the PHONES socket for
monitoring or for private listening. The speakers are automatically
disconnected when headphones are connected.
12
FM outdoor
aerial
AM loop aerial
FM indoor aerial
R ch Speaker L ch Speaker
Video/Auxiliary
equipment
To an AC outlet
Amplifies subwoofer
(not supplied)
- The apparatus shall not be exposed to dripping or splashing.
- Do not use where there are extremes of temperature (below 5°C or
exceeding 35°C) or where direct sunlight may strike it.
- Because of the CD player’s extremely low noise and wide dynamic
range, there might be a tendency to set the volume on the amplifier
unnecessarily high. Doing so may produce an excessively large
output from the amplifier which could damage your speakers.
PRECAUTIONS
CAUTION - USE OF CONTROLS OR ADJUSTMENTS OR PERFOR-
MANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN
THE OPERATING INSTRUCTIONS MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY
ANYONE EXCEPT PROPERLY QUALIFIED PERSONNEL.
-1-
- Sudden changes in the ambient temperature may cause condensa-
tion to form on the optical lens inside the unit. If this happens, take
out the disc, leave the unit for about 1 hour, and then proceed to
operate.
- The system’s speakers use powerful magnets. Do not place
timepieces, credit cards, cassette tapes or video tapes, etc. near the
speakers.
- Do not install this equipment in a confined space, such as a book
case or built in cabinet.
- No objects filled with liquids, such as vases, shall be placed on the
apparatus.
CLASS 1 LASER PRODUCT
LUOKAN 1 LASERLAITE
KLASS 1 LASERAPPARAT
CAUTION – INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM.
ADVARSEL – USYNLIG LASER STRÅLING VED ÅBNING, NÅR
SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION, UNDGÅ UDS ÆTTELSE
FOR STRÅLING.
VARNING – OSYNLIG LASER STRÅLNING NÄR DENNA DEL ÄR ÖPPNAD
OCH SPÄRR ÄR URKOPPLAD. STRÅLEN ÄR FARLIG.
VORSICHT – UNSICHTBARE LASERSTRAHLUNG TRITT AUS, WENN
DECKEL GEÖFFNET UND WENN SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT IST. NICHT, DEM STRAHL AUSSETZEN.
VARO – AVATTAESSA JA SUOJALUKITUS OHITETTAESSA OLET ALTTIINA
NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.

INSTRUCTION MANUAL DC-DA380
Micro Component System
(AU) 1AD6P1P1337-P SANYO Electric Co., Ltd.
Printed in China
MAINTENANCE
Cleaning the tape heads
To ensure continued high performance, use cotton swab to clean the
heads, pinch roller and capstan of the deck after about every 10 hours
of use. If the dirt persists, soak the swab in a little methylated spirit or
head cleaning fluid and then clean.
1. Cotton swab
3, 7. Capstan
4, 6. Pinch roller
2, 5. Heads
Cleaning the CD player lens
The lens should never be touched. If dust is on the lens, blow it off using
a camera lens blower. (Consult your dealer.)
Cleaning the unit
Clean the outside of the unit with a clean soft cloth, moistened with
lukewarm water. Do not use benzene, thinner of alcohol since they will
mar the finish of the surfaces.
-10-
Tuner
Reception frequency:
FM: 87.5 - 108 MHz
AM: 522 -1710 kHz (9 kHz step)
520 - 1710 kHz (10 kHz step)
CD player
Channels:
2-channel stereo
Sampling frequency:
44.1 kHz
Pick-up:
Optical 3-beam semiconductor laser
Laser output:
0.6 mW (Continuous wave max.)
Wave length:
790 nm
Wow/flutter:
Below measurable limits
Cassette deck
Track system:
4-track, 2-channel stereo
Frequency response:
60 Hz to 13.5 kHz
Signal-to-noise ratio:
50 dB
Wow/flutter:
0.12% (WRMS)
Fast forward/rewind time:
Approx. 110 sec. (C-60)
General
Output power:
12.5 W x 2 (at 4 ohms, 10% distortion)
Input
VIDEO IN: 400 mV/50k ohms
Outputs
SPEAKERS: 4 ohms
PHONES: 8 - 32 ohms
Power requirements:
AC 230 - 240 V, 50 Hz
Power consumption:
40 W
Dimensions:
160(W) x 251(H) x 207(D) mm
Weight:
3.2 kg
Speaker systems
Type:
3 way bass reflex
Unit used:
Woofer: 10 cm cone type
Mid range: 5 cm cone type
Tweeter: 2 cm piezoelectric
Maximum power-handling capacity:
25 W (peak)
Nominal impedance:
4 ohms
Dimensions:
150(W) x 245(H) x 224(D) mm
Weight:
1.9 kg (per speaker)
Specifications subject to change without notice.
SPECIFICATIONS
3
2
1
7
456
TIMER OPERATION
Using the timer (Main unit only)
Set the on and off times, and function to be used. Operation will start with
the selected function at the on time. The sound will be gradually
increased from a no-sound level to the current volume setting (fade-in).
The power will be switched off at the off time.
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before
setting the timer.
- Prepare the sources to be used.
- If the function selected is tuner, tune in to the desired band and
station.
- For tape deck: Tape playback will start in the forward direction.
- Adjust the volume level as desired.
Operation
1. Press the FUNCTION button to select the function and set the
desired volume level for timer operation.
2. Press the CLOCK/TIMER button for at least 2 seconds.
The previous timer on time setting appears.
3. Press the MEMORY button within 10 seconds.
4. Set the timer on time by turning the VOLUME control, then press the
MEMORY button (as described under “ADJUDTING THE CLOCK”).
The timer off time setting appears.
5. Set the timer off time as described in step 4.
The previous timer mode/function setting appears.
-“
” blinks only for tuner function, “ ” remains lit for other function.
6. Select the timer mode by turning the VOLUME control (Tuner
function only).
-“
REC” and “ ” blink alternately. Select “ REC” for unattention
recording.
7. Press the MEMORY button (Tuner function only).
The original display returns, then the timer operation standby mode
is activted. “ ” or “ REC” remains lit.
8. Press the z/ON button to switch off the power.
- To switch off the power during a timer controlled operation, press
the z/ON button. The timer will be set in the standby mode.
To release the timer
After turning the power on, press the CLOCK/TIMER button twice. “ ”
or “ REC” disappears.
To set the timer again with the same settings
1. Press the CLOCK/TIMER button repeatedly to display “ ” or “
REC”.
2. Press the z/ON button to switch off the power.
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer (Remote control only)
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
“SLEEP” blinks and the selected time appears on the display. After a few
seconds, the original display returns. “SLEEP” remains blinking.
To check the remaining sleep time
Press the SLEEP button once. After a few seconds, the original display
returns.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until “SLEEP” disappears. The
timer is also released if the power is switched off.
-9-
RECORDING
Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copy-
right material, permission from the copyright owner is necessary.
SANYO does not approve of, and cannot be held responsible for,
any unlawful use of this machine.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during the
recording of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. While “PROG.” is blinking, press the Ubutton to select “bc-1” or
“bc-2”. Select the setting that gives the best results.
Automatic record muting (Remote control only)
Undesirable parts of a programme can be omitted while recording.
Press the rbutton once while recording. “REC” blinks and a 5-second
unrecorded blank space is created, then the deck enters the recording
pause mode. “REC” remains lit and “a” or “b” blinks on the display.
- To add another 5-second blank space, press the rbutton again.
- To resume recording, press the aor bbutton (to match the blinking
“a” or “b”).
Safeguards against accidental erasure
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement.
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive tape and the tape can be used for
recording again.
Break out tab A for side A.
Break out tab B for side B.
Preparation
1. Press the FUNCTION button to select “TAPE”.
2. Load a blank cassette.
3. Press the Ubutton to select the reverse mode.
S: For recording one side only.
W: For recording both sides in succession.
- If recording has been started from the reverse side, only the
reverse side will be recorded.
- If a tape with one of its tabs already broken out is used for
recording, the tape will not be reversed automatically, and it will
stop.
- If the reverse mode has been set to “U”, “W” appears
automatically when the recording mode is established.
Recording compact discs (Synchronous recording)
1. Select “CD” function.
2. Load the disc to be recorded.
- For programmed recording, programme the material in advance
(as described under “PROGRAMMED PLAY”).
3. Select the track number to be recorded if required.
- For programmed recording, this step is unnecessary.
4. Press the jbutton (or the mbutton on the remote control). The
deck enters the recording pause mode and “REC” appears. “b a”
blinks.
5. Press the aor bbutton. Recording starts.
6. Press the nbutton to stop recording. Also the CD player stops
automatically.
Recording from the tuner or other sources
1. Tune in the radio station to be recorded or play other sources.
2. Press the jbutton.
3. Press the aor bbutton. Recording starts.
4. Press the nbutton to stop recording.
Side A
Side B
LISTENING TO OTHER SOURCES
1. Press the FUNCTION button to select “VIDEO: AUX”. 2. Follow the instructions supplied with the Video/ Auxiliary equipment.
-8-
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears, press the
FM MODE button to turn the “MONO” indication off.
“ST” appears when an FM stereo broadcast is received.
- If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to the MONO mode. The
reception may be improved, but the sound will be monaural.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during reception
of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. When “PROG.” is blinking, press the FM MODE button to select “bc-
A” or “bc-B”. Select the setting that gives the best results.
W: For listening to both sides of the tape in succession.
- If playback has been started from the reverse side, only the
reverse side will be played back.
U: For listening repeatedly to both sides of the tape.
LISTENING TO TAPES
LISTENING TO THE RADIO
-7-
If a cassette is loaded, you can turn the unit on and begin play
immediately by pressing the aor bbutton.
1. Press the FUNCTION button to select
“TAPE”.
2. Press the cassette holder (EJECT portion)
to open it.
3. Load the cassette.
After loading the cassette, push the cas-
sette holder (EJECT portion) back into
position. “ ” appears.
4. Press the Ubutton to select the reverse
mode as desired.
S: For listening to one side of the tape
only.
5. Press the aor bbutton to begin playback. “a” or “b” appears.
a: For forward play
b: For reverse play.
6. Press the nbutton to stop playback at any time.
When the end of the tape has been reached, automatic stop or
reverse will be activated.
Note:
- Use the normal tape (TYPE 1).
- Endless tapes cannot be used.
- Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Fast forward and rewind
Press the gor hbutton. “a” or “b” blinks. When the
desired location has been reached, press the nbutton.
Before use
When the unit is shipped from the factory, its AM frequency band is set
as “522 - 1710 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to “520 - 1710 kHz (in 10 kHz steps)” as follows.
1. Press the TUNER/BAND button to select “AM”.
2. While pressing the MEMORY button on the front panel, press the
TUNER/BAND button on the front panel.
To return the original setting, repeat steps above.
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
Automatic/Manual tuning
1. Press the TUNER/BAND button to select FM or AM.
- “TUNER” is selected automatically. “TUNER” appears on the
display, then “TUNER” is replaced by the tuner mode display.
2. Automatic tuning
Press the TU – or + TU button for at least 1 second to tune in a station.
The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the TU – or + TU button briefly until the desired frequency is
displayed.
To preset stations
Up to 24 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic presetting (APT)
1. Press the TUNER/BAND button to select FM or AM.
2. Press the MEMORY button for at least 3 seconds. “PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations for FM, 12 stations for AM have been preset or the
high end of the band is reached, automatic presetting stops.
“PROG.” disappears and the previous received station is heard.
3. To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will
be cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “Automatic/
Manual tuning”.
2. Press the MEMORY button.
3. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the channel num-
ber to be preset.
4. Press the MEMORY button.
- In this example, “103.25 MHz” FM station is preset on FM
channel 9.
- The number buttons on the remote control can be used to pre-
set the station directly. In this example, press 0, then 9 after
the step 2 above.
Note:
If the next step is not taken within 10 seconds while performing
steps 2 - 4, “PROG.” disappears and the preset operation is
cancelled. Press the MEMORY button to continue.
5. Repeat steps above to add more preset stations.
- When presetting a new station, the previous preset station is
cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the desired chan-
nel number. The selected channel number appears briefly.
- The number buttons on the remote control can also be used.
Press two number buttons within 2 seconds.
Preset scan tuning
1. Press the TUNER/BAND button to select AM or FM.
2. Press the PRESET – or PRESET + button (or the PRESET button
on the remote control) for at least 1 second.
- The channel number blinks.
- The preset stations are selected in sequence for approxi-
mately 5 seconds each.
3. Press the PRESET - or PRESET + button (or the PRESET button
bon the remote control) when the desired station has been selected.
Preset scanning will stop.

INSTRUCTION MANUAL DC-DA380
Micro Component System
(AU) 1AD6P1P1337-P SANYO Electric Co., Ltd.
Printed in China
MAINTENANCE
Cleaning the tape heads
To ensure continued high performance, use cotton swab to clean the
heads, pinch roller and capstan of the deck after about every 10 hours
of use. If the dirt persists, soak the swab in a little methylated spirit or
head cleaning fluid and then clean.
1. Cotton swab
3, 7. Capstan
4, 6. Pinch roller
2, 5. Heads
Cleaning the CD player lens
The lens should never be touched. If dust is on the lens, blow it off using
a camera lens blower. (Consult your dealer.)
Cleaning the unit
Clean the outside of the unit with a clean soft cloth, moistened with
lukewarm water. Do not use benzene, thinner of alcohol since they will
mar the finish of the surfaces.
-10-
Tuner
Reception frequency:
FM: 87.5 - 108 MHz
AM: 522 -1710 kHz (9 kHz step)
520 - 1710 kHz (10 kHz step)
CD player
Channels:
2-channel stereo
Sampling frequency:
44.1 kHz
Pick-up:
Optical 3-beam semiconductor laser
Laser output:
0.6 mW (Continuous wave max.)
Wave length:
790 nm
Wow/flutter:
Below measurable limits
Cassette deck
Track system:
4-track, 2-channel stereo
Frequency response:
60 Hz to 13.5 kHz
Signal-to-noise ratio:
50 dB
Wow/flutter:
0.12% (WRMS)
Fast forward/rewind time:
Approx. 110 sec. (C-60)
General
Output power:
12.5 W x 2 (at 4 ohms, 10% distortion)
Input
VIDEO IN: 400 mV/50k ohms
Outputs
SPEAKERS: 4 ohms
PHONES: 8 - 32 ohms
Power requirements:
AC 230 - 240 V, 50 Hz
Power consumption:
40 W
Dimensions:
160(W) x 251(H) x 207(D) mm
Weight:
3.2 kg
Speaker systems
Type:
3 way bass reflex
Unit used:
Woofer: 10 cm cone type
Mid range: 5 cm cone type
Tweeter: 2 cm piezoelectric
Maximum power-handling capacity:
25 W (peak)
Nominal impedance:
4 ohms
Dimensions:
150(W) x 245(H) x 224(D) mm
Weight:
1.9 kg (per speaker)
Specifications subject to change without notice.
SPECIFICATIONS
3
2
1
7
456
TIMER OPERATION
Using the timer (Main unit only)
Set the on and off times, and function to be used. Operation will start with
the selected function at the on time. The sound will be gradually
increased from a no-sound level to the current volume setting (fade-in).
The power will be switched off at the off time.
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before
setting the timer.
- Prepare the sources to be used.
- If the function selected is tuner, tune in to the desired band and
station.
- For tape deck: Tape playback will start in the forward direction.
- Adjust the volume level as desired.
Operation
1. Press the FUNCTION button to select the function and set the
desired volume level for timer operation.
2. Press the CLOCK/TIMER button for at least 2 seconds.
The previous timer on time setting appears.
3. Press the MEMORY button within 10 seconds.
4. Set the timer on time by turning the VOLUME control, then press the
MEMORY button (as described under “ADJUDTING THE CLOCK”).
The timer off time setting appears.
5. Set the timer off time as described in step 4.
The previous timer mode/function setting appears.
-“
” blinks only for tuner function, “ ” remains lit for other function.
6. Select the timer mode by turning the VOLUME control (Tuner
function only).
-“
REC” and “ ” blink alternately. Select “ REC” for unattention
recording.
7. Press the MEMORY button (Tuner function only).
The original display returns, then the timer operation standby mode
is activted. “ ” or “ REC” remains lit.
8. Press the z/ON button to switch off the power.
- To switch off the power during a timer controlled operation, press
the z/ON button. The timer will be set in the standby mode.
To release the timer
After turning the power on, press the CLOCK/TIMER button twice. “ ”
or “ REC” disappears.
To set the timer again with the same settings
1. Press the CLOCK/TIMER button repeatedly to display “ ” or “
REC”.
2. Press the z/ON button to switch off the power.
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer (Remote control only)
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
“SLEEP” blinks and the selected time appears on the display. After a few
seconds, the original display returns. “SLEEP” remains blinking.
To check the remaining sleep time
Press the SLEEP button once. After a few seconds, the original display
returns.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until “SLEEP” disappears. The
timer is also released if the power is switched off.
-9-
RECORDING
Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copy-
right material, permission from the copyright owner is necessary.
SANYO does not approve of, and cannot be held responsible for,
any unlawful use of this machine.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during the
recording of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. While “PROG.” is blinking, press the Ubutton to select “bc-1” or
“bc-2”. Select the setting that gives the best results.
Automatic record muting (Remote control only)
Undesirable parts of a programme can be omitted while recording.
Press the rbutton once while recording. “REC” blinks and a 5-second
unrecorded blank space is created, then the deck enters the recording
pause mode. “REC” remains lit and “a” or “b” blinks on the display.
- To add another 5-second blank space, press the rbutton again.
- To resume recording, press the aor bbutton (to match the blinking
“a” or “b”).
Safeguards against accidental erasure
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement.
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive tape and the tape can be used for
recording again.
Break out tab A for side A.
Break out tab B for side B.
Preparation
1. Press the FUNCTION button to select “TAPE”.
2. Load a blank cassette.
3. Press the Ubutton to select the reverse mode.
S: For recording one side only.
W: For recording both sides in succession.
- If recording has been started from the reverse side, only the
reverse side will be recorded.
- If a tape with one of its tabs already broken out is used for
recording, the tape will not be reversed automatically, and it will
stop.
- If the reverse mode has been set to “U”, “W” appears
automatically when the recording mode is established.
Recording compact discs (Synchronous recording)
1. Select “CD” function.
2. Load the disc to be recorded.
- For programmed recording, programme the material in advance
(as described under “PROGRAMMED PLAY”).
3. Select the track number to be recorded if required.
- For programmed recording, this step is unnecessary.
4. Press the jbutton (or the mbutton on the remote control). The
deck enters the recording pause mode and “REC” appears. “b a”
blinks.
5. Press the aor bbutton. Recording starts.
6. Press the nbutton to stop recording. Also the CD player stops
automatically.
Recording from the tuner or other sources
1. Tune in the radio station to be recorded or play other sources.
2. Press the jbutton.
3. Press the aor bbutton. Recording starts.
4. Press the nbutton to stop recording.
Side A
Side B
LISTENING TO OTHER SOURCES
1. Press the FUNCTION button to select “VIDEO: AUX”. 2. Follow the instructions supplied with the Video/ Auxiliary equipment.
-8-
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears, press the
FM MODE button to turn the “MONO” indication off.
“ST” appears when an FM stereo broadcast is received.
- If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to the MONO mode. The
reception may be improved, but the sound will be monaural.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during reception
of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. When “PROG.” is blinking, press the FM MODE button to select “bc-
A” or “bc-B”. Select the setting that gives the best results.
W: For listening to both sides of the tape in succession.
- If playback has been started from the reverse side, only the
reverse side will be played back.
U: For listening repeatedly to both sides of the tape.
LISTENING TO TAPES
LISTENING TO THE RADIO
-7-
If a cassette is loaded, you can turn the unit on and begin play
immediately by pressing the aor bbutton.
1. Press the FUNCTION button to select
“TAPE”.
2. Press the cassette holder (EJECT portion)
to open it.
3. Load the cassette.
After loading the cassette, push the cas-
sette holder (EJECT portion) back into
position. “ ” appears.
4. Press the Ubutton to select the reverse
mode as desired.
S: For listening to one side of the tape
only.
5. Press the aor bbutton to begin playback. “a” or “b” appears.
a: For forward play
b: For reverse play.
6. Press the nbutton to stop playback at any time.
When the end of the tape has been reached, automatic stop or
reverse will be activated.
Note:
- Use the normal tape (TYPE 1).
- Endless tapes cannot be used.
- Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Fast forward and rewind
Press the gor hbutton. “a” or “b” blinks. When the
desired location has been reached, press the nbutton.
Before use
When the unit is shipped from the factory, its AM frequency band is set
as “522 - 1710 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to “520 - 1710 kHz (in 10 kHz steps)” as follows.
1. Press the TUNER/BAND button to select “AM”.
2. While pressing the MEMORY button on the front panel, press the
TUNER/BAND button on the front panel.
To return the original setting, repeat steps above.
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
Automatic/Manual tuning
1. Press the TUNER/BAND button to select FM or AM.
- “TUNER” is selected automatically. “TUNER” appears on the
display, then “TUNER” is replaced by the tuner mode display.
2. Automatic tuning
Press the TU – or + TU button for at least 1 second to tune in a station.
The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the TU – or + TU button briefly until the desired frequency is
displayed.
To preset stations
Up to 24 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic presetting (APT)
1. Press the TUNER/BAND button to select FM or AM.
2. Press the MEMORY button for at least 3 seconds. “PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations for FM, 12 stations for AM have been preset or the
high end of the band is reached, automatic presetting stops.
“PROG.” disappears and the previous received station is heard.
3. To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will
be cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “Automatic/
Manual tuning”.
2. Press the MEMORY button.
3. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the channel num-
ber to be preset.
4. Press the MEMORY button.
- In this example, “103.25 MHz” FM station is preset on FM
channel 9.
- The number buttons on the remote control can be used to pre-
set the station directly. In this example, press 0, then 9 after
the step 2 above.
Note:
If the next step is not taken within 10 seconds while performing
steps 2 - 4, “PROG.” disappears and the preset operation is
cancelled. Press the MEMORY button to continue.
5. Repeat steps above to add more preset stations.
- When presetting a new station, the previous preset station is
cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the desired chan-
nel number. The selected channel number appears briefly.
- The number buttons on the remote control can also be used.
Press two number buttons within 2 seconds.
Preset scan tuning
1. Press the TUNER/BAND button to select AM or FM.
2. Press the PRESET – or PRESET + button (or the PRESET button
on the remote control) for at least 1 second.
- The channel number blinks.
- The preset stations are selected in sequence for approxi-
mately 5 seconds each.
3. Press the PRESET - or PRESET + button (or the PRESET button
bon the remote control) when the desired station has been selected.
Preset scanning will stop.

INSTRUCTION MANUAL DC-DA380
Micro Component System
(AU) 1AD6P1P1337-P SANYO Electric Co., Ltd.
Printed in China
MAINTENANCE
Cleaning the tape heads
To ensure continued high performance, use cotton swab to clean the
heads, pinch roller and capstan of the deck after about every 10 hours
of use. If the dirt persists, soak the swab in a little methylated spirit or
head cleaning fluid and then clean.
1. Cotton swab
3, 7. Capstan
4, 6. Pinch roller
2, 5. Heads
Cleaning the CD player lens
The lens should never be touched. If dust is on the lens, blow it off using
a camera lens blower. (Consult your dealer.)
Cleaning the unit
Clean the outside of the unit with a clean soft cloth, moistened with
lukewarm water. Do not use benzene, thinner of alcohol since they will
mar the finish of the surfaces.
-10-
Tuner
Reception frequency:
FM: 87.5 - 108 MHz
AM: 522 -1710 kHz (9 kHz step)
520 - 1710 kHz (10 kHz step)
CD player
Channels:
2-channel stereo
Sampling frequency:
44.1 kHz
Pick-up:
Optical 3-beam semiconductor laser
Laser output:
0.6 mW (Continuous wave max.)
Wave length:
790 nm
Wow/flutter:
Below measurable limits
Cassette deck
Track system:
4-track, 2-channel stereo
Frequency response:
60 Hz to 13.5 kHz
Signal-to-noise ratio:
50 dB
Wow/flutter:
0.12% (WRMS)
Fast forward/rewind time:
Approx. 110 sec. (C-60)
General
Output power:
12.5 W x 2 (at 4 ohms, 10% distortion)
Input
VIDEO IN: 400 mV/50k ohms
Outputs
SPEAKERS: 4 ohms
PHONES: 8 - 32 ohms
Power requirements:
AC 230 - 240 V, 50 Hz
Power consumption:
40 W
Dimensions:
160(W) x 251(H) x 207(D) mm
Weight:
3.2 kg
Speaker systems
Type:
3 way bass reflex
Unit used:
Woofer: 10 cm cone type
Mid range: 5 cm cone type
Tweeter: 2 cm piezoelectric
Maximum power-handling capacity:
25 W (peak)
Nominal impedance:
4 ohms
Dimensions:
150(W) x 245(H) x 224(D) mm
Weight:
1.9 kg (per speaker)
Specifications subject to change without notice.
SPECIFICATIONS
3
2
1
7
456
TIMER OPERATION
Using the timer (Main unit only)
Set the on and off times, and function to be used. Operation will start with
the selected function at the on time. The sound will be gradually
increased from a no-sound level to the current volume setting (fade-in).
The power will be switched off at the off time.
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before
setting the timer.
- Prepare the sources to be used.
- If the function selected is tuner, tune in to the desired band and
station.
- For tape deck: Tape playback will start in the forward direction.
- Adjust the volume level as desired.
Operation
1. Press the FUNCTION button to select the function and set the
desired volume level for timer operation.
2. Press the CLOCK/TIMER button for at least 2 seconds.
The previous timer on time setting appears.
3. Press the MEMORY button within 10 seconds.
4. Set the timer on time by turning the VOLUME control, then press the
MEMORY button (as described under “ADJUDTING THE CLOCK”).
The timer off time setting appears.
5. Set the timer off time as described in step 4.
The previous timer mode/function setting appears.
-“
” blinks only for tuner function, “ ” remains lit for other function.
6. Select the timer mode by turning the VOLUME control (Tuner
function only).
-“
REC” and “ ” blink alternately. Select “ REC” for unattention
recording.
7. Press the MEMORY button (Tuner function only).
The original display returns, then the timer operation standby mode
is activted. “ ” or “ REC” remains lit.
8. Press the z/ON button to switch off the power.
- To switch off the power during a timer controlled operation, press
the z/ON button. The timer will be set in the standby mode.
To release the timer
After turning the power on, press the CLOCK/TIMER button twice. “ ”
or “ REC” disappears.
To set the timer again with the same settings
1. Press the CLOCK/TIMER button repeatedly to display “ ” or “
REC”.
2. Press the z/ON button to switch off the power.
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer (Remote control only)
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
“SLEEP” blinks and the selected time appears on the display. After a few
seconds, the original display returns. “SLEEP” remains blinking.
To check the remaining sleep time
Press the SLEEP button once. After a few seconds, the original display
returns.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until “SLEEP” disappears. The
timer is also released if the power is switched off.
-9-
RECORDING
Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copy-
right material, permission from the copyright owner is necessary.
SANYO does not approve of, and cannot be held responsible for,
any unlawful use of this machine.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during the
recording of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. While “PROG.” is blinking, press the Ubutton to select “bc-1” or
“bc-2”. Select the setting that gives the best results.
Automatic record muting (Remote control only)
Undesirable parts of a programme can be omitted while recording.
Press the rbutton once while recording. “REC” blinks and a 5-second
unrecorded blank space is created, then the deck enters the recording
pause mode. “REC” remains lit and “a” or “b” blinks on the display.
- To add another 5-second blank space, press the rbutton again.
- To resume recording, press the aor bbutton (to match the blinking
“a” or “b”).
Safeguards against accidental erasure
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement.
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive tape and the tape can be used for
recording again.
Break out tab A for side A.
Break out tab B for side B.
Preparation
1. Press the FUNCTION button to select “TAPE”.
2. Load a blank cassette.
3. Press the Ubutton to select the reverse mode.
S: For recording one side only.
W: For recording both sides in succession.
- If recording has been started from the reverse side, only the
reverse side will be recorded.
- If a tape with one of its tabs already broken out is used for
recording, the tape will not be reversed automatically, and it will
stop.
- If the reverse mode has been set to “U”, “W” appears
automatically when the recording mode is established.
Recording compact discs (Synchronous recording)
1. Select “CD” function.
2. Load the disc to be recorded.
- For programmed recording, programme the material in advance
(as described under “PROGRAMMED PLAY”).
3. Select the track number to be recorded if required.
- For programmed recording, this step is unnecessary.
4. Press the jbutton (or the mbutton on the remote control). The
deck enters the recording pause mode and “REC” appears. “b a”
blinks.
5. Press the aor bbutton. Recording starts.
6. Press the nbutton to stop recording. Also the CD player stops
automatically.
Recording from the tuner or other sources
1. Tune in the radio station to be recorded or play other sources.
2. Press the jbutton.
3. Press the aor bbutton. Recording starts.
4. Press the nbutton to stop recording.
Side A
Side B
LISTENING TO OTHER SOURCES
1. Press the FUNCTION button to select “VIDEO: AUX”. 2. Follow the instructions supplied with the Video/ Auxiliary equipment.
-8-
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears, press the
FM MODE button to turn the “MONO” indication off.
“ST” appears when an FM stereo broadcast is received.
- If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to the MONO mode. The
reception may be improved, but the sound will be monaural.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during reception
of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. When “PROG.” is blinking, press the FM MODE button to select “bc-
A” or “bc-B”. Select the setting that gives the best results.
W: For listening to both sides of the tape in succession.
- If playback has been started from the reverse side, only the
reverse side will be played back.
U: For listening repeatedly to both sides of the tape.
LISTENING TO TAPES
LISTENING TO THE RADIO
-7-
If a cassette is loaded, you can turn the unit on and begin play
immediately by pressing the aor bbutton.
1. Press the FUNCTION button to select
“TAPE”.
2. Press the cassette holder (EJECT portion)
to open it.
3. Load the cassette.
After loading the cassette, push the cas-
sette holder (EJECT portion) back into
position. “ ” appears.
4. Press the Ubutton to select the reverse
mode as desired.
S: For listening to one side of the tape
only.
5. Press the aor bbutton to begin playback. “a” or “b” appears.
a: For forward play
b: For reverse play.
6. Press the nbutton to stop playback at any time.
When the end of the tape has been reached, automatic stop or
reverse will be activated.
Note:
- Use the normal tape (TYPE 1).
- Endless tapes cannot be used.
- Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Fast forward and rewind
Press the gor hbutton. “a” or “b” blinks. When the
desired location has been reached, press the nbutton.
Before use
When the unit is shipped from the factory, its AM frequency band is set
as “522 - 1710 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to “520 - 1710 kHz (in 10 kHz steps)” as follows.
1. Press the TUNER/BAND button to select “AM”.
2. While pressing the MEMORY button on the front panel, press the
TUNER/BAND button on the front panel.
To return the original setting, repeat steps above.
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
Automatic/Manual tuning
1. Press the TUNER/BAND button to select FM or AM.
- “TUNER” is selected automatically. “TUNER” appears on the
display, then “TUNER” is replaced by the tuner mode display.
2. Automatic tuning
Press the TU – or + TU button for at least 1 second to tune in a station.
The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the TU – or + TU button briefly until the desired frequency is
displayed.
To preset stations
Up to 24 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic presetting (APT)
1. Press the TUNER/BAND button to select FM or AM.
2. Press the MEMORY button for at least 3 seconds. “PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations for FM, 12 stations for AM have been preset or the
high end of the band is reached, automatic presetting stops.
“PROG.” disappears and the previous received station is heard.
3. To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will
be cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “Automatic/
Manual tuning”.
2. Press the MEMORY button.
3. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the channel num-
ber to be preset.
4. Press the MEMORY button.
- In this example, “103.25 MHz” FM station is preset on FM
channel 9.
- The number buttons on the remote control can be used to pre-
set the station directly. In this example, press 0, then 9 after
the step 2 above.
Note:
If the next step is not taken within 10 seconds while performing
steps 2 - 4, “PROG.” disappears and the preset operation is
cancelled. Press the MEMORY button to continue.
5. Repeat steps above to add more preset stations.
- When presetting a new station, the previous preset station is
cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the desired chan-
nel number. The selected channel number appears briefly.
- The number buttons on the remote control can also be used.
Press two number buttons within 2 seconds.
Preset scan tuning
1. Press the TUNER/BAND button to select AM or FM.
2. Press the PRESET – or PRESET + button (or the PRESET button
on the remote control) for at least 1 second.
- The channel number blinks.
- The preset stations are selected in sequence for approxi-
mately 5 seconds each.
3. Press the PRESET - or PRESET + button (or the PRESET button
bon the remote control) when the desired station has been selected.
Preset scanning will stop.

INSTRUCTION MANUAL DC-DA380
Micro Component System
(AU) 1AD6P1P1337-P SANYO Electric Co., Ltd.
Printed in China
MAINTENANCE
Cleaning the tape heads
To ensure continued high performance, use cotton swab to clean the
heads, pinch roller and capstan of the deck after about every 10 hours
of use. If the dirt persists, soak the swab in a little methylated spirit or
head cleaning fluid and then clean.
1. Cotton swab
3, 7. Capstan
4, 6. Pinch roller
2, 5. Heads
Cleaning the CD player lens
The lens should never be touched. If dust is on the lens, blow it off using
a camera lens blower. (Consult your dealer.)
Cleaning the unit
Clean the outside of the unit with a clean soft cloth, moistened with
lukewarm water. Do not use benzene, thinner of alcohol since they will
mar the finish of the surfaces.
-10-
Tuner
Reception frequency:
FM: 87.5 - 108 MHz
AM: 522 -1710 kHz (9 kHz step)
520 - 1710 kHz (10 kHz step)
CD player
Channels:
2-channel stereo
Sampling frequency:
44.1 kHz
Pick-up:
Optical 3-beam semiconductor laser
Laser output:
0.6 mW (Continuous wave max.)
Wave length:
790 nm
Wow/flutter:
Below measurable limits
Cassette deck
Track system:
4-track, 2-channel stereo
Frequency response:
60 Hz to 13.5 kHz
Signal-to-noise ratio:
50 dB
Wow/flutter:
0.12% (WRMS)
Fast forward/rewind time:
Approx. 110 sec. (C-60)
General
Output power:
12.5 W x 2 (at 4 ohms, 10% distortion)
Input
VIDEO IN: 400 mV/50k ohms
Outputs
SPEAKERS: 4 ohms
PHONES: 8 - 32 ohms
Power requirements:
AC 230 - 240 V, 50 Hz
Power consumption:
40 W
Dimensions:
160(W) x 251(H) x 207(D) mm
Weight:
3.2 kg
Speaker systems
Type:
3 way bass reflex
Unit used:
Woofer: 10 cm cone type
Mid range: 5 cm cone type
Tweeter: 2 cm piezoelectric
Maximum power-handling capacity:
25 W (peak)
Nominal impedance:
4 ohms
Dimensions:
150(W) x 245(H) x 224(D) mm
Weight:
1.9 kg (per speaker)
Specifications subject to change without notice.
SPECIFICATIONS
3
2
1
7
456
TIMER OPERATION
Using the timer (Main unit only)
Set the on and off times, and function to be used. Operation will start with
the selected function at the on time. The sound will be gradually
increased from a no-sound level to the current volume setting (fade-in).
The power will be switched off at the off time.
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before
setting the timer.
- Prepare the sources to be used.
- If the function selected is tuner, tune in to the desired band and
station.
- For tape deck: Tape playback will start in the forward direction.
- Adjust the volume level as desired.
Operation
1. Press the FUNCTION button to select the function and set the
desired volume level for timer operation.
2. Press the CLOCK/TIMER button for at least 2 seconds.
The previous timer on time setting appears.
3. Press the MEMORY button within 10 seconds.
4. Set the timer on time by turning the VOLUME control, then press the
MEMORY button (as described under “ADJUDTING THE CLOCK”).
The timer off time setting appears.
5. Set the timer off time as described in step 4.
The previous timer mode/function setting appears.
-“
” blinks only for tuner function, “ ” remains lit for other function.
6. Select the timer mode by turning the VOLUME control (Tuner
function only).
-“
REC” and “ ” blink alternately. Select “ REC” for unattention
recording.
7. Press the MEMORY button (Tuner function only).
The original display returns, then the timer operation standby mode
is activted. “ ” or “ REC” remains lit.
8. Press the z/ON button to switch off the power.
- To switch off the power during a timer controlled operation, press
the z/ON button. The timer will be set in the standby mode.
To release the timer
After turning the power on, press the CLOCK/TIMER button twice. “ ”
or “ REC” disappears.
To set the timer again with the same settings
1. Press the CLOCK/TIMER button repeatedly to display “ ” or “
REC”.
2. Press the z/ON button to switch off the power.
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer (Remote control only)
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
“SLEEP” blinks and the selected time appears on the display. After a few
seconds, the original display returns. “SLEEP” remains blinking.
To check the remaining sleep time
Press the SLEEP button once. After a few seconds, the original display
returns.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until “SLEEP” disappears. The
timer is also released if the power is switched off.
-9-
RECORDING
Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copy-
right material, permission from the copyright owner is necessary.
SANYO does not approve of, and cannot be held responsible for,
any unlawful use of this machine.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during the
recording of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. While “PROG.” is blinking, press the Ubutton to select “bc-1” or
“bc-2”. Select the setting that gives the best results.
Automatic record muting (Remote control only)
Undesirable parts of a programme can be omitted while recording.
Press the rbutton once while recording. “REC” blinks and a 5-second
unrecorded blank space is created, then the deck enters the recording
pause mode. “REC” remains lit and “a” or “b” blinks on the display.
- To add another 5-second blank space, press the rbutton again.
- To resume recording, press the aor bbutton (to match the blinking
“a” or “b”).
Safeguards against accidental erasure
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement.
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive tape and the tape can be used for
recording again.
Break out tab A for side A.
Break out tab B for side B.
Preparation
1. Press the FUNCTION button to select “TAPE”.
2. Load a blank cassette.
3. Press the Ubutton to select the reverse mode.
S: For recording one side only.
W: For recording both sides in succession.
- If recording has been started from the reverse side, only the
reverse side will be recorded.
- If a tape with one of its tabs already broken out is used for
recording, the tape will not be reversed automatically, and it will
stop.
- If the reverse mode has been set to “U”, “W” appears
automatically when the recording mode is established.
Recording compact discs (Synchronous recording)
1. Select “CD” function.
2. Load the disc to be recorded.
- For programmed recording, programme the material in advance
(as described under “PROGRAMMED PLAY”).
3. Select the track number to be recorded if required.
- For programmed recording, this step is unnecessary.
4. Press the jbutton (or the mbutton on the remote control). The
deck enters the recording pause mode and “REC” appears. “b a”
blinks.
5. Press the aor bbutton. Recording starts.
6. Press the nbutton to stop recording. Also the CD player stops
automatically.
Recording from the tuner or other sources
1. Tune in the radio station to be recorded or play other sources.
2. Press the jbutton.
3. Press the aor bbutton. Recording starts.
4. Press the nbutton to stop recording.
Side A
Side B
LISTENING TO OTHER SOURCES
1. Press the FUNCTION button to select “VIDEO: AUX”. 2. Follow the instructions supplied with the Video/ Auxiliary equipment.
-8-
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears, press the
FM MODE button to turn the “MONO” indication off.
“ST” appears when an FM stereo broadcast is received.
- If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to the MONO mode. The
reception may be improved, but the sound will be monaural.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during reception
of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. When “PROG.” is blinking, press the FM MODE button to select “bc-
A” or “bc-B”. Select the setting that gives the best results.
W: For listening to both sides of the tape in succession.
- If playback has been started from the reverse side, only the
reverse side will be played back.
U: For listening repeatedly to both sides of the tape.
LISTENING TO TAPES
LISTENING TO THE RADIO
-7-
If a cassette is loaded, you can turn the unit on and begin play
immediately by pressing the aor bbutton.
1. Press the FUNCTION button to select
“TAPE”.
2. Press the cassette holder (EJECT portion)
to open it.
3. Load the cassette.
After loading the cassette, push the cas-
sette holder (EJECT portion) back into
position. “ ” appears.
4. Press the Ubutton to select the reverse
mode as desired.
S: For listening to one side of the tape
only.
5. Press the aor bbutton to begin playback. “a” or “b” appears.
a: For forward play
b: For reverse play.
6. Press the nbutton to stop playback at any time.
When the end of the tape has been reached, automatic stop or
reverse will be activated.
Note:
- Use the normal tape (TYPE 1).
- Endless tapes cannot be used.
- Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Fast forward and rewind
Press the gor hbutton. “a” or “b” blinks. When the
desired location has been reached, press the nbutton.
Before use
When the unit is shipped from the factory, its AM frequency band is set
as “522 - 1710 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to “520 - 1710 kHz (in 10 kHz steps)” as follows.
1. Press the TUNER/BAND button to select “AM”.
2. While pressing the MEMORY button on the front panel, press the
TUNER/BAND button on the front panel.
To return the original setting, repeat steps above.
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
Automatic/Manual tuning
1. Press the TUNER/BAND button to select FM or AM.
- “TUNER” is selected automatically. “TUNER” appears on the
display, then “TUNER” is replaced by the tuner mode display.
2. Automatic tuning
Press the TU – or + TU button for at least 1 second to tune in a station.
The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the TU – or + TU button briefly until the desired frequency is
displayed.
To preset stations
Up to 24 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic presetting (APT)
1. Press the TUNER/BAND button to select FM or AM.
2. Press the MEMORY button for at least 3 seconds. “PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations for FM, 12 stations for AM have been preset or the
high end of the band is reached, automatic presetting stops.
“PROG.” disappears and the previous received station is heard.
3. To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will
be cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “Automatic/
Manual tuning”.
2. Press the MEMORY button.
3. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the channel num-
ber to be preset.
4. Press the MEMORY button.
- In this example, “103.25 MHz” FM station is preset on FM
channel 9.
- The number buttons on the remote control can be used to pre-
set the station directly. In this example, press 0, then 9 after
the step 2 above.
Note:
If the next step is not taken within 10 seconds while performing
steps 2 - 4, “PROG.” disappears and the preset operation is
cancelled. Press the MEMORY button to continue.
5. Repeat steps above to add more preset stations.
- When presetting a new station, the previous preset station is
cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the desired chan-
nel number. The selected channel number appears briefly.
- The number buttons on the remote control can also be used.
Press two number buttons within 2 seconds.
Preset scan tuning
1. Press the TUNER/BAND button to select AM or FM.
2. Press the PRESET – or PRESET + button (or the PRESET button
on the remote control) for at least 1 second.
- The channel number blinks.
- The preset stations are selected in sequence for approxi-
mately 5 seconds each.
3. Press the PRESET - or PRESET + button (or the PRESET button
bon the remote control) when the desired station has been selected.
Preset scanning will stop.

INSTRUCTION MANUAL DC-DA380
Micro Component System
(AU) 1AD6P1P1337-P SANYO Electric Co., Ltd.
Printed in China
MAINTENANCE
Cleaning the tape heads
To ensure continued high performance, use cotton swab to clean the
heads, pinch roller and capstan of the deck after about every 10 hours
of use. If the dirt persists, soak the swab in a little methylated spirit or
head cleaning fluid and then clean.
1. Cotton swab
3, 7. Capstan
4, 6. Pinch roller
2, 5. Heads
Cleaning the CD player lens
The lens should never be touched. If dust is on the lens, blow it off using
a camera lens blower. (Consult your dealer.)
Cleaning the unit
Clean the outside of the unit with a clean soft cloth, moistened with
lukewarm water. Do not use benzene, thinner of alcohol since they will
mar the finish of the surfaces.
-10-
Tuner
Reception frequency:
FM: 87.5 - 108 MHz
AM: 522 -1710 kHz (9 kHz step)
520 - 1710 kHz (10 kHz step)
CD player
Channels:
2-channel stereo
Sampling frequency:
44.1 kHz
Pick-up:
Optical 3-beam semiconductor laser
Laser output:
0.6 mW (Continuous wave max.)
Wave length:
790 nm
Wow/flutter:
Below measurable limits
Cassette deck
Track system:
4-track, 2-channel stereo
Frequency response:
60 Hz to 13.5 kHz
Signal-to-noise ratio:
50 dB
Wow/flutter:
0.12% (WRMS)
Fast forward/rewind time:
Approx. 110 sec. (C-60)
General
Output power:
12.5 W x 2 (at 4 ohms, 10% distortion)
Input
VIDEO IN: 400 mV/50k ohms
Outputs
SPEAKERS: 4 ohms
PHONES: 8 - 32 ohms
Power requirements:
AC 230 - 240 V, 50 Hz
Power consumption:
40 W
Dimensions:
160(W) x 251(H) x 207(D) mm
Weight:
3.2 kg
Speaker systems
Type:
3 way bass reflex
Unit used:
Woofer: 10 cm cone type
Mid range: 5 cm cone type
Tweeter: 2 cm piezoelectric
Maximum power-handling capacity:
25 W (peak)
Nominal impedance:
4 ohms
Dimensions:
150(W) x 245(H) x 224(D) mm
Weight:
1.9 kg (per speaker)
Specifications subject to change without notice.
SPECIFICATIONS
3
2
1
7
456
TIMER OPERATION
Using the timer (Main unit only)
Set the on and off times, and function to be used. Operation will start with
the selected function at the on time. The sound will be gradually
increased from a no-sound level to the current volume setting (fade-in).
The power will be switched off at the off time.
The timer will function every day unless it is released.
Preparation
Note:
Make absolutely sure that the clock is set to the correct time before
setting the timer.
- Prepare the sources to be used.
- If the function selected is tuner, tune in to the desired band and
station.
- For tape deck: Tape playback will start in the forward direction.
- Adjust the volume level as desired.
Operation
1. Press the FUNCTION button to select the function and set the
desired volume level for timer operation.
2. Press the CLOCK/TIMER button for at least 2 seconds.
The previous timer on time setting appears.
3. Press the MEMORY button within 10 seconds.
4. Set the timer on time by turning the VOLUME control, then press the
MEMORY button (as described under “ADJUDTING THE CLOCK”).
The timer off time setting appears.
5. Set the timer off time as described in step 4.
The previous timer mode/function setting appears.
-“
” blinks only for tuner function, “ ” remains lit for other function.
6. Select the timer mode by turning the VOLUME control (Tuner
function only).
-“
REC” and “ ” blink alternately. Select “ REC” for unattention
recording.
7. Press the MEMORY button (Tuner function only).
The original display returns, then the timer operation standby mode
is activted. “ ” or “ REC” remains lit.
8. Press the z/ON button to switch off the power.
- To switch off the power during a timer controlled operation, press
the z/ON button. The timer will be set in the standby mode.
To release the timer
After turning the power on, press the CLOCK/TIMER button twice. “ ”
or “ REC” disappears.
To set the timer again with the same settings
1. Press the CLOCK/TIMER button repeatedly to display “ ” or “
REC”.
2. Press the z/ON button to switch off the power.
Note:
The timer operation is released if a power failure occurs.
Using the sleep timer (Remote control only)
The sleep timer automatically switches off the power after a preset time
has elapsed. The volume will gradually be reduced (fade-out) during the
1-minute period before the unit turns off. There are 12 time periods
available: 120, 110, 100, 90, 80, 70, 60, 50, 40, 30, 20, and 10 minutes.
Press the SLEEP button repeatedly to select the desired sleep time.
“SLEEP” blinks and the selected time appears on the display. After a few
seconds, the original display returns. “SLEEP” remains blinking.
To check the remaining sleep time
Press the SLEEP button once. After a few seconds, the original display
returns.
To release the sleep timer while in operation
Press the SLEEP button repeatedly until “SLEEP” disappears. The
timer is also released if the power is switched off.
-9-
RECORDING
Recording copyright material without permission of the copyright
owners is usually an infringement. If you wish to re-record copy-
right material, permission from the copyright owner is necessary.
SANYO does not approve of, and cannot be held responsible for,
any unlawful use of this machine.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during the
recording of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. While “PROG.” is blinking, press the Ubutton to select “bc-1” or
“bc-2”. Select the setting that gives the best results.
Automatic record muting (Remote control only)
Undesirable parts of a programme can be omitted while recording.
Press the rbutton once while recording. “REC” blinks and a 5-second
unrecorded blank space is created, then the deck enters the recording
pause mode. “REC” remains lit and “a” or “b” blinks on the display.
- To add another 5-second blank space, press the rbutton again.
- To resume recording, press the aor bbutton (to match the blinking
“a” or “b”).
Safeguards against accidental erasure
Accidental erasure can be prevented by breaking out the tabs on the end
of the cassette tape (where the tape is not exposed) using a screwdriver
or similar implement.
If a tab is broken out in error and you wish to re-record the tape, simply
block the tab hole using adhesive tape and the tape can be used for
recording again.
Break out tab A for side A.
Break out tab B for side B.
Preparation
1. Press the FUNCTION button to select “TAPE”.
2. Load a blank cassette.
3. Press the Ubutton to select the reverse mode.
S: For recording one side only.
W: For recording both sides in succession.
- If recording has been started from the reverse side, only the
reverse side will be recorded.
- If a tape with one of its tabs already broken out is used for
recording, the tape will not be reversed automatically, and it will
stop.
- If the reverse mode has been set to “U”, “W” appears
automatically when the recording mode is established.
Recording compact discs (Synchronous recording)
1. Select “CD” function.
2. Load the disc to be recorded.
- For programmed recording, programme the material in advance
(as described under “PROGRAMMED PLAY”).
3. Select the track number to be recorded if required.
- For programmed recording, this step is unnecessary.
4. Press the jbutton (or the mbutton on the remote control). The
deck enters the recording pause mode and “REC” appears. “b a”
blinks.
5. Press the aor bbutton. Recording starts.
6. Press the nbutton to stop recording. Also the CD player stops
automatically.
Recording from the tuner or other sources
1. Tune in the radio station to be recorded or play other sources.
2. Press the jbutton.
3. Press the aor bbutton. Recording starts.
4. Press the nbutton to stop recording.
Side A
Side B
LISTENING TO OTHER SOURCES
1. Press the FUNCTION button to select “VIDEO: AUX”. 2. Follow the instructions supplied with the Video/ Auxiliary equipment.
-8-
To receive FM stereo broadcasts
Make sure that “MONO” is not displayed. If “MONO” appears, press the
FM MODE button to turn the “MONO” indication off.
“ST” appears when an FM stereo broadcast is received.
- If the signal from an FM stereo station is weak and reception is poor,
press the FM MODE button to change to the MONO mode. The
reception may be improved, but the sound will be monaural.
When beat interference is heard
A high-pitched noise called “beat” is sometimes heard during reception
of radio broadcasts. If this occurs.
1. Press the MEMORY button.
2. When “PROG.” is blinking, press the FM MODE button to select “bc-
A” or “bc-B”. Select the setting that gives the best results.
W: For listening to both sides of the tape in succession.
- If playback has been started from the reverse side, only the
reverse side will be played back.
U: For listening repeatedly to both sides of the tape.
LISTENING TO TAPES
LISTENING TO THE RADIO
-7-
If a cassette is loaded, you can turn the unit on and begin play
immediately by pressing the aor bbutton.
1. Press the FUNCTION button to select
“TAPE”.
2. Press the cassette holder (EJECT portion)
to open it.
3. Load the cassette.
After loading the cassette, push the cas-
sette holder (EJECT portion) back into
position. “ ” appears.
4. Press the Ubutton to select the reverse
mode as desired.
S: For listening to one side of the tape
only.
5. Press the aor bbutton to begin playback. “a” or “b” appears.
a: For forward play
b: For reverse play.
6. Press the nbutton to stop playback at any time.
When the end of the tape has been reached, automatic stop or
reverse will be activated.
Note:
- Use the normal tape (TYPE 1).
- Endless tapes cannot be used.
- Do not use C-100 (or longer) tapes. They may jam in the mechanism.
Fast forward and rewind
Press the gor hbutton. “a” or “b” blinks. When the
desired location has been reached, press the nbutton.
Before use
When the unit is shipped from the factory, its AM frequency band is set
as “522 - 1710 kHz (in 9 kHz steps)”.
If your local AM broadcast system is organized in 10 kHz steps, change
the frequency band to “520 - 1710 kHz (in 10 kHz steps)” as follows.
1. Press the TUNER/BAND button to select “AM”.
2. While pressing the MEMORY button on the front panel, press the
TUNER/BAND button on the front panel.
To return the original setting, repeat steps above.
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
Automatic/Manual tuning
1. Press the TUNER/BAND button to select FM or AM.
- “TUNER” is selected automatically. “TUNER” appears on the
display, then “TUNER” is replaced by the tuner mode display.
2. Automatic tuning
Press the TU – or + TU button for at least 1 second to tune in a station.
The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the TU – or + TU button briefly until the desired frequency is
displayed.
To preset stations
Up to 24 stations for FM band, and up to 12 stations for AM band can be
preset.
Automatic presetting (APT)
1. Press the TUNER/BAND button to select FM or AM.
2. Press the MEMORY button for at least 3 seconds. “PROG.” blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations for FM, 12 stations for AM have been preset or the
high end of the band is reached, automatic presetting stops.
“PROG.” disappears and the previous received station is heard.
3. To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will
be cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in “Automatic/
Manual tuning”.
2. Press the MEMORY button.
3. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the channel num-
ber to be preset.
4. Press the MEMORY button.
- In this example, “103.25 MHz” FM station is preset on FM
channel 9.
- The number buttons on the remote control can be used to pre-
set the station directly. In this example, press 0, then 9 after
the step 2 above.
Note:
If the next step is not taken within 10 seconds while performing
steps 2 - 4, “PROG.” disappears and the preset operation is
cancelled. Press the MEMORY button to continue.
5. Repeat steps above to add more preset stations.
- When presetting a new station, the previous preset station is
cleared.
Listening to preset stations
1. Press the TUNER/BAND button to select FM or AM.
2. Press the PRESET – or PRESET + button on the front panel (or
PRESET button on the remote control) to select the desired chan-
nel number. The selected channel number appears briefly.
- The number buttons on the remote control can also be used.
Press two number buttons within 2 seconds.
Preset scan tuning
1. Press the TUNER/BAND button to select AM or FM.
2. Press the PRESET – or PRESET + button (or the PRESET button
on the remote control) for at least 1 second.
- The channel number blinks.
- The preset stations are selected in sequence for approxi-
mately 5 seconds each.
3. Press the PRESET - or PRESET + button (or the PRESET button
bon the remote control) when the desired station has been selected.
Preset scanning will stop.