Sanyo C14PL60 User manual

S* o
INSTRUCTION MANUAL C14PL60 C14PL60Z
C20PV60 C20PV60Z
C21 PS60 C21 PS60Z
Colour Television
@@@@@@@@@@@@@
@@@@@@@@@@@@@
@@@@@@@@@@@@@
@@@a@@@@@@@@@
@@@@@@@@@@@@@
@e@@@e@@@@@@@
@@@@@@@@@@@@@
@@@@@@@@@@@@@
*eel@@@@@@@@@@
@@@@@@@@@@@@@
eke@@@@@@@@@@
PAL System
Special Function
Video Multi Terminal (PAUNTSCAITSC4.43)

AWarning
High voltages are used in the operation of this
television receiver. Do not remove the cabinet
back from your set. Refer servicing to qualified
service personnel.
A
Warning
To prevent fire or electrical shock hazard, do not
expose the television receiver to rain or moisture.
AWarning
Do not drop or push objects into the television
cabinet slots or openings. Never spill any kind
of liquid on the television receiver.
,. ., ,.
-.
--) &NItiC)II Avoid exposing the television receiver to
;::
,-.., , , ,
...., .
..
~~&&
~ad AIdirect suniight and other sources of heat. Do not
t$.●..
:: ●stand the television receiver directly on other
rproducts which give off heat. E.g. video cassette
piayers, audio amplifiers.
J’j& ‘UJicofnponents.
Do not biock the ventilation hoies in the back cover.
Adequate ventdatlon ISessential to prevent failure of
&JiyJfA
ICaution
●Do not squash power suppiy cord under the
01 television receiver.
Minimum distancea
1Ocm 1Ocm ACaution
I
Em
-5cm
a!if the television is to be built into a
●compartment or similariy enclosed, the
c1
minimum distances must be maintained.
Heat build-up can reduce the service life
of your television, and can aiso be
dangerous.
–l–

filllllllllllllllw
uR
[1
‘//
I
““’A
fll
mnI
Model C14PL60L7 wConnect the cable with aplugI11
‘u Iyfrom aUHF (or VHF) aerial to
the aerialsocketon the cabinetI
I111111111111111111111111111111111111%
11111111111111111111111111111111111111111r. I
1111111111111
mulllt
111111111111111111111
L~&-4
I I 1s11111s111111mllllll —1- 1=
IAerial Cable
lr.erial Socket
\IllRm/ ‘4
‘(Y%T’
Model C20PV60AZ, C21PS60L7
1~1
l’r.efial Socket
For all aerial circuit probiems piease consult your iocai deaier.
–2-

-. #- ●●✎✎
~1
FUNCTION ~—
SOUND MUTE @—
OFF TIMER ~—z
\-
Programme
~UP/DOWN
~LEVEL
~ALTERNATE
~Power ON/OFF
~TV/AV Selector
—This button is not used
Battery installation of the Remote Control Transmitter
❑Removethe batterycover.
❑Installtwo“AA” 1.5 volt batteriessothatthe “+” and
“-” marksonthe batteriesmatch the “+” and “-”
marksinsidethe unit.
❑Closethe batterycover.
Note:Replace the batteries when the TV set is
showingthe followingsymptoms:
Operationis unsteadyor erratic, sometimesthe
TV setdoesnotworkwithtransmitter.
Dischargedbatteriesmay leak and damagethe
unit. The normal life of batteriesshouldbe from
nineto ten months. [Battery cover removal ]
–3–
t

Each button listed in this section has the same function as it’s corresponding
button on the remote controi.
Model C14PL60Z
II LStandby and Power Ret!!ote Control
indicator \ti Detector
II
i
MEMORY/ PRESET ~LEVEL~ $Ogramme &
FUNCTION IUP/DOWN Mains ON/OFF
switch
Model C20PV60R
Remote Control
Detector 7
Stand-by and
,_+\J I
PUSH
Push to open 9Mains ON/OFF
Switch
Model C21PS60R
Remote Control
Detector
1
Stand-by and Power
Indicator \
I1
A(“m,
a
//
vMains ON/OFF Switch O
P—M AUTO
TART -A+ VPA
?9- 1I I 1
Pro ramme
MEMORY/PRESET OUP/LOWN
LEVEL
–4–

~Power ON/OFF J
To switch the TV on, press the Mains ON/OFF switch ~on the front of the TV set.
If no picture appears, press the Power ON/OFF button ~on the remote control
transmitter.
To turn the TV on from the standby condition, press any of the following buttons:
Power ON/OFF~, Programme UP/DOWN@ or 1to 9 and Obutton ~.
AUTO SHUT OFF
This TV set incorporatesthe AUTO SHUT OFF function.
Even if the TV is left on after you have gone to sleep, the TV
L
29
–10
set changes to the standby mode within 10 minutes after all
broadcasts have ended. RemainingTime —
/
QQ??
l! A
~Caution
●
.1 ,1, When the television receiver is not used for
an extended period of time, it is advisable to
1% disconnect the AC power cord from the AC
outlet.
[Programme Selection (Direct Selection) 1
To select programme 8directly, press 8button of the Programme Selector ~on the
remote control .8
618
To select programme 10
“- Press the Digit ~button
6‘-&J_~~bution
To select programme 27
“-- Press the Digit ~button 2
6~-??l-~~bu”on
I
–5–

(Programme Selection (Programme Up and Down) )
You can step upwards to the next programme position by pressing the PAbutton ~on
the remote control transmitter or the TV set. Or step downwards using the PY button.
[Volume Control )
Increase or decrease the Sound volume level by pressing
the LEVEL (+or –)buttons ~ASOUND
111111---------
fSound Mute 1
Should you wish to mute the sound (e.g. While talking on
the telephone), press the SOUND MUTE @button.
To switch the sound back on, press the SOUND MUTE H
button again.
(Recall )
To display the on screen indications, press
r
Programme
the RECALL/COLOUR SYSTEM @button. Position
Off Timer /
Screen display disappears after about 529
seconds. -30
[Alternate J
Press the ALTERNATE @button, and the
programme position will alternately select the
previous position and the present position. m:m
[Off Timer 1
Press the OFF TIMER @button. I-00—>1 -30+1 -60
The TV set will be turned off after about No Ofltimer
30,60,90 or 120 minutes. 30 minutes 60 minutes
To cancel the OFF TIMER:
Press the OFF TIMER button L@-&
until” –00” appears. 120 minutes 90 minutes
Just one minute before switchingoff the
lv, ”– 01 “and channelnumberwill be
displayedonthe screen. u
–6–

[Memory )
This function lets You store the settings (for colour, brightness, contrast, sharpness! sound
volume) in the memory for both p=ture and sound-, and these setting levels can be
recalled by pressing the NORMALIZATION @button of the remote control transmitter.
To store the picture and sound settings
met’=
❑Set the pictureand soundto the desirable levels.~ ~ ~~”ND
$
❑Press the MEMORY/PRESETO ~button while the control function display is still
visible on the screen.
Note:The control settings will not be saved if the MEMORY
buttonis pressedafter the controlfunctiondisplayhas left =
the screen,
(Normalization )
Press the NORMALIZATION button @. And the colour,
brightness, contrast, sharpness and sound volume settings
which you stored using the MEMORY button are recalled. &
[Picture Adjustment 1
IPress the FUNCTION@ button repeatedly to select the following functions.
Each time the FUNCTION button is pressed, function choice will change as follows;
@!&&@@4-
Colour Intensity Brightness
+
Contrast
T
(OperativeforNTSC4.43 Ikii
TINT
and NTSCsignalonly)- ll[l[lll[ll--.-
U“w” Display off Fine tuning
(OperativeforTV modeonly)
Increase or decrease the levelof the chosenfunctionby pressingthe LEVEL@
+
Tint
MSHARPNESS
11111111111---- I
I
Sharpness
+or –button. -7-

.0. . . . ●.* ●e- Oe .“ e
~1
It is possible to set the maximum sound volume at your preference and
suppresses the channel tuning function, so that even If the MEMORY/PRESET
button is pressed, the channel tuning mode(preset mode) will remain inactive.
[Setting procedure )
❑
ISet the desirable volume level using the LEVELQ button.
ASOUND The volume level set in this procedure will be
111111--------- memorized as the maximum volume level.
❑
2Press and hold the FUNCTION @button on the front control
panel of the TV set, then press the RECALL/COLOUR SYSTEM
@button on the remote control transmitter.
l~~~~til---- ]e,C ~1 ITEM-l SET+, ,
3Select “SET+ 1” by pressing the LEVEL( +or –)@button.
“m“
Eachtimethe LEVELbuttonis pressed,
settingmodechangesasfollows;
Sm+o ~SET+l
•1
4Press the RECALL/COLOUR SYSTEM @button to return to the normal TV mode.
(Cance//hg procedure )
II
1
•1
2
❑
3
Press and hold the FUNCTION ~button on the front control panel of
the TV set, then press the RECALL/COLOUR SYSTEM @button on
the remote control transmitter.
ITEM-1 SET +1
Select “SET- 0“, by pressing the LEVEL( +or –)~button.
IITEM-1 SET +O
Press the RECALL/COLOUR SYSTEM @button to return to the normal TV mode.
–8–
t

This function can be used to change the startup condition of the TV set.
When “ITEM –2“ is set to “SET +1”, AV mode is always selected when the TV is
turned on.
mu
(Setting procedure
When the TV set is turned on,
AV mode is always seiected.
II
1Press and hoid the FUNCTION @button on the front control panel of the TV set, then
press the RECALUCOLOUR SYSTEM@ button on the remote control transmitter.
l~flR,----le~.+‘EM-’‘ET+O
•1
2Select” ITEM –2” by pressing the FUNCTION ~button.
uEach time the FUNCTION button is
pressed, setting item changes as foiiows;
lTEM-1~1’TEM-2
~Seiect” SET+ 1“by pressing the LEVEL(+ or - ) @button of the remote
Ucontrol transmitter or the TV set.
❑
4Press the RECALL/COLOUR SYSTEM @button to return to the normal TV mode.
[Canceiiing procedure 1
Enter to the setting mode using mode using above procedure ~Select “iTEM –2“ by
pressing the FUNCTION button ~Change “SET ~1” to “SET+ O“ by pressing the
LEVEL( +or- )button ~Press the RECALL/COLOUR SYSTEM button to return to
the normai TV mode. Start up condition of the TV set return to the factory
m‘Urnedono
shipment condition, meaning that the previously viewed
programmepositionis alwaysselectedwhenthe TV set is
-9–