Sartorius ISBBS User manual

Operating Instructions
Sartorius ISBBS, ISDCS
Weighing Platform
98648-019-05

2ISBBS, ISDCS Operating Instructions
Table of Contents
Table of Contents
Copyright .............................................................................3
Intended Use........................................................................3
Warnings and Safety Precautions ....................................4
Getting Started...................................................................5
Installation Instructions.....................................................6
Leveling the Weighing Platform ...................................6
Ground Conductor...........................................................6
Data Interface.....................................................................7
Pin Assignment ................................................................7
Menu Access Switch...........................................................8
Specifications ......................................................................9
ISBBS Weighing Data.......................................................10
ISDCS Weighing Data.......................................................11
Error Messages..................................................................12
Care and Maintenance.....................................................13
Cleaning Stainless Steel Surfaces...............................14
Disposal ..............................................................................15
Potentially Explosive Atmosphere ..................................16
Dimensions (Scale Drawings)...........................................18

ISBBS, ISDCS Operating Instructions 3
Legal Terms and Conditions
Copyright
This documentation may not be reproduced or distributed either in whole or in
part without the explicit written permission of Sartorius.
This documentation is intended only for use by the buyer.
Transfer to third parties, whether free or in exchange for payment, is not
permitted.
The software is the property of Sartorius. The software may not be copied or
modified; it may not be decompiled or modified through assimilation.
The buyer may only use the software for his own purposes and may not make
the software available to third parties for use either for free or in exchange for
payment. If you encounter problems with the included software, please contact
the software distributor. Sartorius reserves the right to deliver updated software
for this product.
No liability is accepted for software installed before the purchase of this product.
The buyer is liable for any misuse of the product.
Intended Use
As precise and robust weighing platforms, the ISBBS and ISDCS provide
reliable weighing results. The models are based on monolithic
technology (the principle of electromagnetic force compensation).
These industrial weighing platforms offer the following special features:
– Robust and durable Sartorius quality
– IP65 protection from dust and jets of water
– High-quality workmanship and materials
– Preload values can be defined (for equipment installed on the scale)

4ISBBS, ISDCS Operating Instructions
Safety Precautions
Warnings and Safety Precautions
3 Read these operating instructions thoroughly before using the weighing
platform, in order to prevent damage to the equipment.
3 The weighing platforms comply with the European Council Directives as well as
international regulations and standards for electrical equipment, electromagnetic
compatibility, and the stipulated safety requirements.
3 Do not expose the equipment to aggressive chemical vapors or to unnecessarily
extreme temperatures, moisture, shocks, or vibration.
2 Avoid generating static electricity and connect equipotential bonding terminals.
3 All models meet the criteria for protection class IP65.
Any installation work that does not conform to the instructions in this manual
results in forfeiture of all claims under the manufacturer’s warranty.
3 If there is any indication that safe operation of the equipment is no longer
guaranteed, disconnect the platform from the power and ensure that it is not
used further.
3 Always ensure that the weighing platform is disconnected from AC power before
performing any maintenance, cleaning, or repair work.
3 Note the pin assignments when using cables provided by other manufacturers.
Check the connections of the cable against the corresponding cabling diagram
before connecting to the Sartorius equipment and disconnect any wires that are
assigned differently. The operator shall be solely responsible when using cables
not supplied by Sartorius.
3 The weight value can be affected by extreme electromagnetic influences.
Once the disturbance has ceased, the instrument can be used again in
accordance with its intended purpose.

ISBBS, ISDCS Operating Instructions 5
Getting Started
Getting Started
Warning:
3 Unpacked devices can lose their precision if subject to extreme vibrations.
Excessive vibrations may compromise the safety of the equipment. Do not
expose the equipment to unnecessarily extreme temperatures, moisture,
shocks, or vibrations.
Permitted storage temperature: -10°C to +40°C
Unpacking the Equipment
Remove the device from the packaging. Check for any visible damage. Save the
original packaging for any future transport. Unplug all connected cables before
packing the equipment.
Acclimatizing the Device
3 The device should only be opened by trained and qualified personnel.
Before opening the valve unit: Turn the main switch to “OFF." Take all steps
necessary to secure the equipment against unauthorized power-up.
Disconnect the device from the power supply if possible.
Once work is completed: Securely lock the valve unit.
Scope of Supply:
– Weighing platform
– Operating instructions
– Special accessories as listed on the bill of delivery, if ordered

6ISBBS, ISDCS Operating Instructions
Installation Instructions
Installation Instructions
t Set up a suitable installation location for the weighing platform.
The place of installation should be dry, level, and flat. The operating temperature
ranges from -10°C to +40°C.
The weighing platform must not be subjected to unnecessarily extreme
temperatures, moisture, shocks, or vibrations that could result in damage.
Leveling the Weighing Platform
Purpose: – To compensate for uneven areas at the place of installation
– To ensure that the equipment is placed in a perfectly horizontal
position for consistently reproducible weighing results
Always level the weighing platform again any time after it has been moved to
a different location.
t Level the weighing platform using the four leveling feet. Turn the feet until
the air bubble is centered in the level indicator.
t Check to ensure that all leveling feet rest securely on the work surface.
y Each of the leveling feet must support an equal load.
y Adjusting the leveling feet:
To raise the weighing platform, extend the leveling feet (turn counterclockwise).
To lower the weighing platform, retract the leveling feet (turn clockwise).
Ground Conductor
The ground conductor is located underneath the weighing pan on the clamp
box or on the lower base of the weighing platform. It is marked as a ground
connection with the symbol shown here.
Grounding is implemented using a threaded bolt or screw terminal, or as a hole.
If a ground hole is the method of grounding, a stainless steel screw and nut
must be used. A lock washer should be placed underneath in order to prevent
the screw from loosening. The grounding cable must have a minimum cross-
section of 4 mm2 and must be fitted with a suitable ring terminal. Connect
all equipment, including peripheral devices, to the equipotential bonding
conductor.
°C

ISBBS, ISDCS Operating Instructions 7
Data Interface
The weighing platform has a standard COM1 interface, RS-485 socket (IP65).
The standard COM1 interface can be converted to RS-232 through the
Sartorius Service Center.
Pin Assignment
COM 1 round plug connector with screw connection.
Front view:
RS-485 data interface RS-232 data interface
A RxD–TxD–N Not used
B Not used RxD
C Not used TxD
D Not used CTS
E GND GND
F Menu access switch
for adjustment
Menu access switch
for adjustment
G 12-30 VDC 2W supply 12-30 VDC 2W supply
H Not used DTR
J GND GND
K GND GND
L RxD–TxD–P Not used
M 12-30 VDC 2W supply 12-30 VDC 2W supply
h Female Interface Connector (Recommended):
Type C091D, 12-pin, Amphenol (IP65) cable type as per AWG 24
Observe power supply instructions.
Operation as an RS485-interface:
Switch 4 must be open in order to switch to RS-485 operation (factory setting).
Where applicable, deactivate bias resistors for RS-485 operation. Open switches
for this purpose (factory setting).There must only be one instance of bias
resistors per transmission path (network orpoint-to-point connection). Otherwise
there is a risk of transmission errors. Where applicable, refer to the specifications
or circuit documentation for the remote station or network nodes in question.
Bias resistors must always be activated or deactivated in pairs. The terminating
resistor (transmitting side, switch 1 must be activated if the device is located at
either end of an RS-485 bus system, or where it is connected to another device
in a point-to-point link. There must also be a terminating resistor of 120 Ω in
place at the remote station. Where applicable, activate terminating resistor 120
Ω for RS-485operation:
Terminating resistor, receiving side 120 ΩSwitch 1 on
BIAS resistor, receiving side (RxD+, pull-up) 680 ΩSwitch 2 on
BIAS resistor, receiving side (RxD–, pull-down) 680 ΩSwitchr 3 on
No function Switch 4
Data Interface

8ISBBS, ISDCS Operating Instructions
Menu Access Switch
Menu Access Switch
ISBBS
Switch on the right = for use in legal metrology
Switch on the left = external calibration/adjustment accessible
ISDCS
Switch on the right = for use in legal metrology
Switch on the left = external calibration/adjustment accessible

ISBBS, ISDCS Operating Instructions 9
Specifications
Specifications
General Specifications
The CE conformity is only guaranteed when using Sartorius accessories.
Digital protective interface as per EN 45501
Data interface RS-485
Housing: material
Protection class as per EN 60529
stainless steel
IP65
Temperature range –10°C to +40°C
Humidity max. relative humidity is 80% for temperatures up to 31°C
DC supply optional 15.524 V DC (±10%), max. 12 W via interface
Interference emission as per EN 61326+A1, Class B (IEC 61326+A1)
Interference immunity as per EN 61326+A1, industrial areas (IEC 61326+A1)
Electrical safety as per EN 61010-1 (IEC 61010-1), EN 60950 (IEC 60950)

10 ISBBS, ISDCS Operating Instructions
ISBBS Weighing Data
ISBBS Weighing Data
Non-verifiable Models
Weighing capacity (kg) 3.1 6.1
Readability (g) 0.01 0.01
Resolution code -H -H
Calibration weight value
(in grams)
2000 5000
Accuracy class E2 E2
Preload (kg) 3 0
Reproducibility (g) 0.01 0.01
Linearity (g) 0.02 0.02
Ambient temperature -10°C to +40°C