Satel ACCO-KP2 User manual

21 ACCO-KP2 SATEL
ACCO-KP2
Access control module ACCO
USER MANUAL
EN
Firmware version 1.00 acco-kp2_u_en 06/22
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. [phone]
www.satel.eu

IMPORTANT
Before you start using the module, please read carefully this manual in order to avoid
mistakes that can lead to malfunction or even damage to the equipment.
Changes, modifications or repairs not authorized by the manufacturer shall void your rights
under the warranty.
SATEL aims to continually improve the quality of its products, which may result in changes in
their technical specifications and software. The current information on the introduced
modifications is available on our website.
Please visit us:
https://support.satel.pl
The declaration of conformity may be consulted at www.satel.eu/ce
Factory default code:
Administrator code: 12345
The following symbols may be used in this manual:
- note,
- caution.

CONTENTS
1. Introduction........................................................................................................................3
2. Glossary............................................................................................................................3
3. Users.................................................................................................................................4
3.1 User authorization ....................................................................................................................4
3.2 Authorization by using two identifiers........................................................................................5
3.3 Code.........................................................................................................................................5
3.3.1 Factory default code ......................................................................................................................5
3.4 User rights................................................................................................................................5
4. Using the ACCO-KLCDR keypad......................................................................................5
4.1 Description of the keypad.........................................................................................................6
4.1.1 LEDs ..............................................................................................................................................6
4.1.2 Display ...........................................................................................................................................7
4.1.3 Keys ...............................................................................................................................................7
4.1.4 Built-in proximity card reader .........................................................................................................7
4.1.5 Audible signaling............................................................................................................................7
4.2 Unlocking the door....................................................................................................................8
4.2.1 Getting access ...............................................................................................................................8
Getting access by using the code.......................................................................................................8
Getting access by using the proximity card ........................................................................................8
Getting access by using two identifiers...............................................................................................8
4.2.2 On duty...........................................................................................................................................8
4.2.3 Access denied................................................................................................................................8
4.3 Other functions available when the code is used......................................................................9
4.3.1 User menu......................................................................................................................................9
List of functions ...................................................................................................................................9
4.3.2 Blocking the door ...........................................................................................................................9
4.3.3 Unblocking the door.......................................................................................................................9
4.3.4 Restoring the door to normal operation mode ...............................................................................9
4.3.5 Changing the code.......................................................................................................................10
4.3.6 Module data .................................................................................................................................10
4.4 Other functions available when the proximity card is used......................................................10
4.4.1 Blocking the door .........................................................................................................................10
4.4.2 Unblocking the door.....................................................................................................................10
4.4.3 Restoring the door to normal operation mode .............................................................................10
5. Using the ACCO-SCR keypad.........................................................................................10
5.1 Description of the keypad.......................................................................................................11
5.1.1 LEDs ............................................................................................................................................11
5.1.2 Keys .............................................................................................................................................11
5.1.3 Built-in proximity card reader.......................................................................................................11
5.1.4 Audible signaling..........................................................................................................................12
5.2 Unlocking the door..................................................................................................................12
5.2.1 Getting access .............................................................................................................................12
Getting access by using the code.....................................................................................................12
Getting access by using the proximity card ......................................................................................12
Getting access by using two identifiers.............................................................................................12
5.2.2 Access denied..............................................................................................................................13
5.3 Other functions available when the code is used....................................................................13
5.3.1 Blocking the door .........................................................................................................................13
5.3.2 Unblocking the door.....................................................................................................................13
5.3.3 Restoring the door to normal operation mode .............................................................................13
5.4 Other functions available when the proximity card is used......................................................13
5.4.1 Blocking the door .........................................................................................................................13
5.4.2 Unblocking the door.....................................................................................................................13
5.4.3 Restoring the door to normal operation mode .............................................................................14

SATEL ACCO
2
6. Using the proximity card readers.....................................................................................14
6.1 Description of the CZ-EMM and CZ-EMM2 readers...............................................................14
6.1.1 Bicolor LED ................................................................................................................................. 14
6.2 Description of the CZ-EMM3 and CZ-EMM4 readers.............................................................15
6.2.1 LEDs............................................................................................................................................ 15
6.2.2 Bell key........................................................................................................................................ 15
6.3 Audible signaling....................................................................................................................15
6.4 Unlocking the door.................................................................................................................16
6.4.1 Getting access ............................................................................................................................ 16
6.4.2 Access denied............................................................................................................................. 16
6.5 Other functions.......................................................................................................................16
6.5.1 Blocking the door ........................................................................................................................ 16
6.5.2 Unblocking the door.................................................................................................................... 16
6.5.3 Restoring the door to normal operation mode ............................................................................ 17
7. Using the CZ-DALLAS reader .........................................................................................17
7.1 Description of the CZ-DALLAS reader....................................................................................17
7.1.1 Bicolor LED ................................................................................................................................. 17
7.2 Unlocking the door.................................................................................................................17
7.2.1 Getting access ............................................................................................................................ 17
7.2.2 Access denied............................................................................................................................. 17
7.3 Other functions.......................................................................................................................18
7.3.1 Blocking the door ........................................................................................................................ 18
7.3.2 Unblocking the door.................................................................................................................... 18
7.3.3 Restoring the door to normal operation mode ............................................................................ 18
8. Unlock button...................................................................................................................18
9. Other ways to block the door...........................................................................................18
10. Other ways to unblock the door.......................................................................................19
11. Other ways to restore the door to normal operation mode...............................................19

SATEL ACCO-KP2 3
1. Introduction
Thank you for choosing our product. We hope you will be satisfied with your choice. Please
remember that we are always ready to provide you with professional assistance and
information on our products. Visit our website www.satel.eu to find more information about
the products offered by SATEL sp. z o.o.
The ACCO-KP2 module is used to control the access to a room, a building or an area. Its job
is to control a single door. Only an authorized person will be able to open the door. Devices
connected to the module, such as LCD keypads, keypads or readers, are used to identify
which person is authorized. The person who is authorized to open the door has the right
identifier (card / code). The access can be limited to particular hours on selected days.
In this manual you will find information on how to use the ACCO-KP2 module as a stand-
alone device or as a part of the ACCO access control system.
2. Glossary
Access denied –response to when an unauthorized user attempts to get access (the user
has an unknown identifier or is not authorized to get access at the time).
Access granted –permission to open the door after the user is identified and the user rights
are verified.
Access schedule –schedule that is assigned to the user and used to define the rules of
access to a door. Days and hours during which the user has access to the door are
specified in the access schedule.
Access time –time during which you will be able to open the door after you get access.
Alarm –warning of a situation that may compromise the operation of the access control
module (e.g. door opened by force, tamper etc.). Action is required to address this
situation. The alarm can be signaled in the LCD keypad, keypad or reader.
Anti Passback –function that prevents the user with access from passing back the identifier
to other persons so that they can get access. The function prohibits repeated entry or exit
by using the same identifier.
Anti-Scanner –function that prevents any attempts to test different code combinations /
different cards or Dallas iButtons in order to get access. If 5 attempts are made within
3 minutes to get access by using an unknown identifier, the terminals will be blocked for
5 minutes.
Authorized entry –opening the door by the user when access was granted after using the
entry terminal.
Authorized exit –opening the door by the user when access was granted after using the exit
terminal.
Code –string of digits used to identify the user.
Dallas iButton –chip inside a metal can shaped like a button. Each Dallas iButton has
a unique and fixed code used to identify the user.
Door –general name for a barrier that prevents unrestricted access to a protected area.
This can be a hinged door, gate, turnstile, arm barrier etc.
Door blocked –module operating mode in which access to the door cannot be granted
(the door is permanently locked).
Door opened by force –opening the door without getting access (when the door is locked).

SATEL ACCO-KP2 4
Door status control –module that supervises the door status by using a sensor connected
to the module input. The sensor reports it when the door is opened or closed.
Door unblocked –module operating mode in which access to the door is not controlled and
anyone can open it (the door is permanently unlocked).
Door unlocking –response of the module when a user is granted access.
Identifier –card, Dallas iButton, key tag or code used to identify the user.
Input activation –change of the input status to another, different from that defined for the
normal status.
Installer –the person who has installed and configured the access control module.
Long open door –it is interpreted by the module that the door is open for too long when the
door is open for longer than the “Door open time” limit.
Mantrap / airlock –door that consists of at least two doors. In order to be able to open the
next door in the mantrap / airlock, you must first close the previous door. Only one door at
a time can be opened in the mantrap / airlock.
Normal door operating mode –module operating mode in which access to the door is
controlled. It is the default operating mode of the door.
Proximity card –passive transponder in the form of a card, key tag etc. Each card has
a unique and fixed code used to identify the user.
Quit entry / exit –not opening the door after the user is granted access.
Tamper –opening the enclosure of the module, LCD keypad, keypad etc.
Terminal –device used to identify the user, e.g. LCD keypad, keypad, proximity card reader
or Dallas iButton reader. Ask the installer about the terminal if you want to find out if it acts
as the entry terminal or the exit terminal.
Terminal blocked –terminal does not respond when an identifier is used. This happens
when the “Anti-Scanner” function is at work.
Unlock button –button or external device connected to the module input that allows you to
open the door without using the user identifier.
User –person registered in the module who gets access by using an identifier.
3. Users
Users can be added in the ACCO-SOFT-LT program.
3.1 User authorization
Identification of the user and verification of the user rights is required for the purpose of
access control. The user can be identified based on:
code,
proximity card,
Dallas iButton.
Do not make your code available to other people.
If an unknown identifier is used five times, this can:
trigger an alarm,
block the terminal for 5 minutes.

5 ACCO-KP2 SATEL
3.2 Authorization by using two identifiers
The ACCO-KLCDR and ACCO-SCR keypads have a built-in proximity card reader.
The installer can configure these devices so that the user must use two identifiers for
authorization, both code and card.
3.3 Code
The code is a string of 4 to 12 digits.
If you use the code in the ACCO-KLCDR keypad, a message can be displayed asking
you to change the code. The message will be displayed every time you use the code,
until you change it.
3.3.1 Factory default code
This code is programmed in the module by default: 12345. The code is assigned to the
“Administrator” user with ID number 00001.
The user with ID number 00001 cannot be deleted from the module. The user’s
“Administrator” and “Change code” rights cannot be revoked either.
You should change the factory code before you start using the access control
module (see: “Changing the code”).
3.4 User rights
Administrator –the user can:
display the module identifier in the LCD keypad,
clear the alarm memory.
Switching –the user can:
change the door status to blocked,
change the door status to unblocked,
restore the door to normal operation mode.
The user can only change the door status by using the terminal when, according to the
access schedule, the user has access to that door.
Change code –the user can change the code by using the ACCO-KLCDR keypad.
4. Using the ACCO-KLCDR keypad
If the ACCO-KLCDR keypad is connected to the module, the users can use the code or the
proximity card.

SATEL ACCO-KP2 6
Fig. 1. ACCO-KLCDR keypad.
4.1 Description of the keypad
4.1.1 LEDs
LED
Color
Description
yellow
ON –door blocked (permanently locked)
flashing slowly –door blocked (permanently locked) after the
“Alarm – block door” type of input is activated
green
ON –door unblocked (permanently unlocked)
flashing slowly –door unblocked (permanently unlocked) after the
“Fire – unblock door” type of input is activated
flashing rapidly –access to door granted
green
LED not used
red
ON –alarm
flashing –alarm memory

7 ACCO-KP2 SATEL
4.1.2 Display
The information presented on the display help the user communicate with the module. Date
and time are displayed in the upper line. The installer can define the keypad backlight mode
and the time format to be shown on the display.
4.1.3 Keys
Use the number keys to enter the code. Use the other keys to:
- open the user menu (after you enter the code),
- exit the user menu / function,
- quit changing the code.
/
- get access (after you enter the code),
- run the function,
- confirm new code.

- exit the user menu / function,
- move the cursor left when changing the code.

- scroll up the list of functions,
- delete digits when changing the code,
- confirm that entry / exit is made on duty.

- scroll down the list of functions.

- run the function,
- move the cursor right when changing the code.
4.1.4 Built-in proximity card reader
The reader supports the Unique 125 kHz proximity cards and key fobs.
4.1.5 Audible signaling
1 short beep –access granted and door unlocked.
2 short beeps –door blocked, unblocked or restored to normal mode.
3 short beeps –waiting for the second identifier to be used.
1 long beep –access denied (known card or code). The user cannot unlock the door
because:
the keypad only grants access based on the code but the card has been used,
the keypad only grants access based on the card but the code has been entered.
2 long beeps –access denied (card or code unknown).
3 long beeps [after you present the card / enter the code and press / ] –access
denied (known card or code). The user cannot unlock the door because:
the user is not authorized to unlock the door according to the access schedule,
the door is blocked,
the user exceeded the defined limit of entries,
the user tries again to enter or exit –the “Anti Passback” option is enabled,
the module operates in the mantrap / airlock configuration and the other door is open.
3 long beeps [after you hold the card] –impossible to change the door status (block /
unblock / restore to normal mode), because the door status is not controlled.

SATEL ACCO-KP2 8
1 very long beep –access denied (the keypad is blocked by the “Anti-Scanner” function).
Long beep lasting 10 seconds –alarm.
4.2 Unlocking the door
The door will unlock when you are granted access. When the door is unlocked, you will be
able to open the door. The installer should tell you how much time you have to open the door
after access is granted and how much time you have to close the door. The installer should
also tell you which of the following procedures to use in order to get access.
If alarm memory is signaled in the keypad (the LED is flashing), the alarm memory
will be cleared as soon as the user with the “Administrator” right is granted access.
4.2.1 Getting access
Getting access by using the code
1. Enter the code and press or .
2. When the LED will start flashing, open the door.
Getting access by using the proximity card
1. Present the card on the keypad reader.
2. When the LED will start flashing, open the door.
Getting access by using two identifiers
1. Use the first identifier.
2. When the message will be displayed that the keypad is waiting for the second identifier –
use the second identifier.
3. When the LED will start flashing, open the door.
4.2.2 On duty
After you are granted access, when the message “On duty” is displayed (Fig. 2), you can
press to register the entry / exit as made for official purposes. Ignore the message if your
entry / exit is not connected with your official duties.
Fig. 2. Message on the possibility to register entry / exit as made for official purposes.
4.2.3 Access denied
The door will remain locked if:
the identifier is unknown,
the user cannot get access because:
the keypad only grants access based on the card, but the code has been entered,
the keypad only grants access based on the code, but the card has been used,