saunalife E6 User manual

@saunalife
E Mood E6/E7 /ES
Installation Manual
Mood RGB Light

2
LED Lightbar Package Contents:
RF Driver/Receiver
(qty. 1)
Power Supply
(qty. 1)
RGB Remote
(qty. 1)
4-Pin 30’ Cable
(qty. 1)
AC Power Cable
(qty. 1)
RGB Led Mood Light
(qty. 1)

3
Installaon Recommendaons
Please read this manual in its entirety prior to installation and keep it somewhere
accessible for future reference.
The RF Driver and Power Supply may be installed outdoors but must be
protected from rain and snow. RF Driver and Power Supply should be installed
in a waterproof electrical enclosure.
When installing the RF Driver and Power Supply inside the sauna, maintain a
minimum distance of 20” from heat source and a maximum height of 20” o
floor or in path of fan.
If installed inside the sauna, the RF Control must not exceed 131°F. Control
should be no more than 3' off the floor and away from heater. Test
temperature reading of location before mounting.
LED Light Bar max operating temperature is 195°F, installing LED light bar in
location where temperature will exceed 195°F may cause light failure.
Electrical Requirements
•A 120V AC electrical outlet is needed to power the lighng
system.
•Your electrician will determine the type of electrical outlet,
box, and piping to be used.
•All wiring must be done in accordance with naonal elec-
tric code and local building codes by a cered electrician.
•Improper voltage or connecons will damage the compo-
nents and void warranty.
IMPORTANT
IMPORTANT
IMPORTANT
IMPO RTANT

4
STEP 1.
Mount RF Driver / Receiver
Using 2 screws mount RF driver to desired surface. Driver should be mounted in
a dry accessible location for service.
Note: Do not install within 20” of sauna heater and a maximum of 20” off oor.
STEP 2.
Run 4-Pin 30’ Cable
Run 4-Pin 30’ light cable from Driver to LED Mood Light. At Driver connect
cable end to pigtail off driver.

5
STEP 3.
Install Mood Light
Take Mood light xture and two screws, lift xture to ceiling ensuring that it’s
centered within the room. Drive two screws, one on each end securing xture
to ceiling of barrel. Take 4-Pin cable and connect to pigtail off Mood light.
STEP 4.
Install Power Supply
Connect AC power cord cable to power supply block. Place power supply
near RF driver. Connect DC cable end from power supply and connect into
RF driver DC IN port.

6
STEP 6.
RGB Control Installation
Take holder and separate back mounting plate from holder. At mounting
location, screw mounting plate to surface. Slide holder from top down onto
mounting the plate.

7
Control Operation
Follow the steps below for control operation. After 30 seconds of inactivity the remote will
enter sleep mode. To wake up the control, press any button.
LED Indicator On/O
Hold to Dim
Double Click for White
RGB Touch Slide
•Verify that all connections are secure and complete before proceeding.
•Ensure DC-out end of Power Supply is plugged into DC-in of the Driver.
•Plug AC power cable from the Power Supply into a 120V AC electrical outlet.
•Verify that the Driver powers on. The indicator light will ash purple rapidly for
approximately 20 seconds.
STEP 7.
Startup & Testing
STEP 9.
RF Driver & Dimming Remote Programming
Note: RF Driver is preprogrammed. Follow steps below if programming is needed.
1) Press and hold the Match button until the Run Indicator light changes to white.
Note: The Run indicator will turn off, then rapidly ash purple. White run indicator will
be after Blue.
2) Release the Match button, then short press once to save programming.
3) Hold remote, then on Driver press match button once then quickly press the power
button on remote.

8
On IOS or Android down-
load the Tuya Smart App
Step 1 Step 2 Step 3 Step 4
Step 5 Step 6 Step 7
Wi-Fi Setup
Step 9
To set up Wi-Fi operation follow the steps
below
Note: Wi-Fi Driver supports 802.11 b / g / n
2.4 GHz Wi-Fi standard. The Wi-Fi Driver
Device added success-
fully, press done to
complete setup
Select your
Wi-Fi network
Press Add next to
Discovering
Devices
Main screen
press Add Device
Open Tuya app
and press Sign
Up to create
an account
Enter an email
address to regis-
ter an account
Check email and
enter vericaon
code
Create a
password

9
RF Driver/Receiver
Operang Voltage: 24V DC
Rated Out Current: 5CH, 3A/CH
Output Voltage: 12-24V DC
Max Output Power: 5Ch X 72W
Operang Temp: -22°F - 131°F
Dimensions: 4.48”L x 1.49”W x .78”H
Light Capacity: 4 Lights / 20’ (per Driver)
IP Rang: IP20
Cercaons: CE. EMC, LVD, RED
RF Remote Single-Zone RGB
Output Signal: RF (2.4GHz)
Operang Voltage: 3V DC (CR2032)
Power Consumpon: 5mA
Dimming Range: 1% - 100%
Signal Distance: 98FT
Dimensions: 5.47”L x 1.41”W x .43”H
Operang Temp: -22°F - 131°F
Zones: 1 Zone Single Color
IP Rang: IP20
Cercaons: CE, EMC, LVD, RED
PART
NUMBER
Operating
Voltage (VDC) Max Wattage Lumens Dimensions
210-BP031072 24V DC 41.95W 1,885 47-1/4" x 12-1/2" x
3-3/8"
Mood Light Specicaons
RGB Operang Temp:
-13°F to 230°F IP Rang: IP67
Power Supply
Input Voltage: 120VA C
Output Voltage: 24V DC
Rated Power: 90W
AC Current: 1.3A
DC Current: 3.75A
Operang Temp: -22°F - 158°F
IP Rang: IP20
Cercaons: UL, CE, FCC
Specications

10
No Power
•Verify that the electrical outlet has voltage.
•Check that connections on Power Supply are secure.
•Check that the DC barrel plug connection on the Power Supply is secure.
Power but lights not turning on
•Check that the Pigtail cable from the Driver is securely connected and that
wiring is correct (see step #1).
•Check that 4-way light cable is secure and connected.
•Check that all 30’ cables to lights are securely connected.
•Verify each light functions by testing them directly to the Driver independently.
Note: To test individual light, disconnect 4-way light cable and connect 30’ cable
directly to Pigtail lead off Driver, or connect light directly Pigtail.
•Verify that RF Remote is paired with Driver, see page #7.
Lights on no function from Control
•Verify battery is inserted correctly.
•If battery is low, replace with new battery.
•Check that DC power cable from Driver to Control is securely connected.
•Ensure that the distance from the Remote to the Driver is not more than 98
feet. If so, relocate Driver closer to room.
Resetting Driver
The Driver should not need to be reset in normal conditions. If a reset is needed, follow the
steps below.
•Verify power to Driver
•Press and hold the Match button for 10-15 seconds until the blue LED indica-
tor ashes rapidly.
Note: Resetting Driver will clear any paired remotes and require repairing.
Replacement Parts
Description Part Number
Driver BP031108
Power Supply/90W BP031137
RF Control Single-Zone RGB BP031151
4-PIN IP67 Pigtail BP031074
4-PIN IP67 30' Cable BP031078
Troubleshooting
Mood Light 210-BP031072