saunalife Ergo Series User manual

W h i t e L E D L i g h t b a r

2
Installation Recommendations
Please read this manual in its entirety prior to installation
and keep it accessible for future reference.
The RF Driver and Power Supply may be installed outdoors but must be
protected from rain and snow. RF Driver and Power Supply should be installed
in a waterproof electrical enclosure.
When installing the RF Driver and Power Supply inside the sauna, maintain a
minimum distance of 20” from heat source and a maximum height of 20” off
of the floor or in the fan's path.
If installed inside the sauna, the RF Control must not exceed 131°F. Control
should be no more than 3' off the floor and away from heater. Test
temperature reading of location before mounting.
Consider light placement carefully. Each fixture should be placed to avoid
direct contact with the eyes of the bathers using the fixture.
LED Light Bar max operating temperature is 195°F. Installing the LED light bar
in a location where the temperature will exceed 195°F may cause light failure.
Electrical Requirements
•A 120V AC electrical outlet is needed to power the lighting
system.
•Your electrician will determine the type of electrical outlet,
box, and piping to be used.
•All wiring must be done in accordance with national elec-
tric code and local building codes by a certified electrician.
•Improper voltage or connections will damage the compo-
nents and void the warranty.
IMPORTANT
IMPORTANT
IMPORTANT
IMPORTANT
IMPOR
TANT

3
System Components
LED Lightbar Package Contents:
RF Driver / Receiver
(qty. 1)
Power Supply
(qty. 1)
Dimming Remote
(qty. 1)
2-Pin 4-Way Cable
(qty. 1)
2-Pin 30’ Cable
(qty. 1)
AC Power Cable
(qty. 1)
Adjustable Mounting Clips
(qty. 3)
Stationary Mounting Clips
(qty. 3)
White Led Light Bar
(qty. 1)

4
STEP 2.
Locate 2-Pin 4-way cable and connect single end to 2-Pin Pigtail of Driver.
STEP 3.
Run 30’ light cable from Driver to LED light bar.
Note: Repeat this step if installing more than one light.
Installation
STEP 1.
Mount RF Driver/Receiver to surface using 2 screws.
Note: Do not install within 20” of sauna heater and a maximum of 20” off floor.

5
To Light To Driver
STEP 5.
Connect the light cable end to the splitter
cable that leads to the Driver.
Connect opposite end of the light cable to the
Pigtail leading to the light bar.
Note: See below for cable connections
Installation
STEP 4.
Determine the location where your LED light
will be installed. Screw Mounting Clips to
surface ensuring even coverage of
light .fixture. Take the LED light bar and
carefully snap bar into each clip.
Adjustable
Stationary

6
Installation
STEP 6.
−RF Remote includes a wall mount
holder for storing.
−Take holder and slide back mounting
plate from holder.
−At mounting location screw mounting
plate to surface.
−Slide holder from top down onto
mounting the plate.
# 1
Mounting Plate
# 2
Holder
# 3
Control on Holder
Caution: Control and mount should not be
installed higher than 3' or within 2' of heat
source

7
Control Operation
Follow the steps below for control operation. After 30 seconds of inactivity the remote
will enter sleep mode. To wake up the control, press any button.
LED Indicator
On / Off
100%
50%
1%
Brightness Control
Startup & Testing
•Verify that all connections are secure and complete before proceeding.
•Plug the DC-out end of your Power Supply into the DC-in of the Driver.
•Plug the Power Supply line into a 120V AC electrical outlet.
•Verify that the Driver power is on. The indicator light will .flash purple rapidly
for approximately 20 seconds.
Driver & Remote Programming
Note: The Driver is pre-programmed. Follow steps below if programming is needed.
1) Press and hold the Match button until the Run Indicator light changes to white.
Note: The Run indicator will turn off, then rapidly flash purple. White run indicator will be
after Blue.
2) Release the Match button, then short press once to save programming.
3) Grab remote then on Driver press match button once then quickly press the power button on
remote.
Note: If you encounter any issues during startup and testing proceed to troubleshooting
steps.

8
On IOS or Android
download the
Tuya Smart App
Step 1 Step 2
Enter an email
address to regis-
ter an account
Step 3
Check email and
enter verification
code
Step 4
Create a
password
Step 5
Main screen
press Add Device
Step 6
Press Add next to
Discovering
Devices
Step 7
Select your
Wi-Fi network
Wi-Fi Setup Continued
To set up Wi-Fi operation follow the steps below
Note: Wi-Fi Driver supports 802.11 b / g / n 2.4 GHz Wi-Fi standard. The Wi-Fi
Driver will not connect with 5 GHz network.
Step 9
Device added success-
fully, press done to
complete setup
Open Tuya app
and press Sign
Up to create
an account

24V DC
5CH, 3A/CH
12-24V DC
5Ch X 72W
-22°F - 131°F
4.48”L x 1.49”W x .78”H
4 Lights / 20’ (per Driver)
IP20
Specifications
RF Driver/Receiver
Operating Voltage:
Rated Out Current:
Output Voltage:
Max Output Power:
Operating Temp:
Dimensions:
Light Capacity:
IP Rating:
Certifications: CE. EMC, LVD, RED
RF Remote Single-Zone Dimming
RF (2.4GHz)
3V DC (CR2032)
5mA
1% - 100%
98FT
5.47”L x 1.41”W x .43”H
-22°F - 131°F
Output Signal:
Operating Voltage:
Power Consumption:
Dimming Range:
Signal Distance:
Dimensions:
Operating Temp:
Zones: 1 Zone Single Color
Part
Number
Operating
Voltage (VDC)
Max
Wattage Lumens Dimensions (with flush clips)
Dimensions
(with adjusta-
ble clips)
E6
BP031085
LED White 24V DC 11.32W 1,246 3/4W x 9/16H x
48L
3/4W x 1-1/4H x
48L
E7
BP031086
LED White 24V DC 14.27W 1,571 3/4W x 9/16H x
60L
3/4W x 1-1/4H x
60L
LED Light Bar Specifications
Kelvin: 3500k Operating Temp:
-13°F to 195°F
Max Run: 4 Light
Bars / 20 Linear Feet IP Rating: IP67
Power Supply
Input Voltage: 120VA C
Output Voltage: 24V DC
Rated Power: 90W
AC Current: 1.3A
DC Current: 3.75A
Operating Temp: -22°F - 158°F
IP Rating: IP20
Certifications: UL, CE, FCC
E8
BP031158
LED White 24V DC 18.69W 2,059 3/4W x 9/16H x
76L
3/4W x 1-1/4H x
76L
9

10
Troubleshooting
No Power
•Verify that the electrical outlet has voltage.
•Check that connections on Power Supply are securely connected.
•Check that the DC barrel plug on the Power Supply is securely
connected.
Power but light's not turning on
•Check that the Pigtail cable from the Driver is securely connected and that wiring
is correct (see step #1).
•Check that 4-way light cable is secure and connected.
•Check that all 30’ cables to lights are securely connected.
•Verify each light functions by testing them directly to the Driver independently.
Note: To test individual light, disconnect 4-way light cable and connect
30’ cable directly to Pigtail lead oĀff Driver, or connect light directly Pigtail.
•Verify that RF Remote is paired with Driver, see page #7.
Lights on with no function from Control
•Verify battery is inserted correctly.
•Low battery, replace with new battery.
•Check DC power cable from Driver to Control is securely connected.
•Ensure that the distance from the Remote to the Driver is not more than 98
feet. If so, relocate Driver closer to room.
Resetting Driver
The Driver should not need to be reset in normal conditions. If a reset is needed, follow the
steps below.
•Verify power to Driver
•Press and hold the Match button for 10-15 seconds until the blue LED
indicator flashes rapidly.
Note: Resetting Driver will clear any paired remotes and require repairing.
Replacement Parts
Description Part Number
Driver BP031108
Power Supply/90W BP031137
RF Control Single-Zone White BP031111
4-Way IP67 2-PIN Splitter BP031075
2-PIN IP67 Pigtail BP031073
48” White Light Bar BP031085
60” White Light Bar BP031086
2-PIN IP67 30' Cable BP031077
76” White Light Bar BP031158