Savant SHR-2000 User manual

SHR-2000 Quick Reference Guide | 009-1909-03 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 210611 1 of 2 Savant.com | 508.683.2500
Front Panel
Power Status
A B C
APower LED
Green: System has power and is operating
normally.
O: System is not receiving power.
B
Status LED
O: Disconnected from power supply.
Amber: Host is booting/rebooting and is
disconnected from the network.
Green: Connected to the local network and is
assigned an IP Address.
CMounting
Points
Threaded insert for use with optional rack
mounts
Box Contents
(1) Savant® Smart Host Rack Mountable - (SHR-2000)
(1) Install Kit (075-0223-xx)
(1) Multi-Blade 5V DC 3A Power Supply (025-0223-xx)
(2) 6-pin Screw Down Plug-in Connector (028-9352-xx)
(2) 3-pin Screw Down Plug-in Connector (028-9351-xx)
(1) Product and Regulatory Insert (009-1950-xx)
Specifications
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% Relative Humidity (non-condensing)
Cooling 10 CFM
Maximum BTU 34.1 BTU/hr
Dimensions and Weights
Height Width Depth Weight
Device 1.6 in
(4.15 cm)
8.5 in
(21.50 cm)
3.7 in
(9.33 cm)
1.4 lbs
(0.64 kg)
Shipping 2.2 in
(5.59 cm)
12 in
(30.48 cm)
7.3 in
(18.54 cm)
2.3 lbs
(1.05 kg)
Rack Space 1U
Power
Input Power 5V DC 3A
Maximum Power 15 watts
Power over
Ethernet (PoE) IEEE 802.3af
Regulatory
Safety and
Emissions
FCC Part 15 CE C-Tick UKCA
RoHS Compliant
Minimum Supported Release
Savant OS da Vinci 9.2
Chassis Installation
The Smart Host can be installed on a solid, flat, level surface such as a
table, cabinet, or shelf. The location should be dry, well ventilated, and
out of direct sunlight.
Rack
The optional RMB-PAVAM2F-xx or RMB-PAVAM2-xx allows two
devices to be mounted side by side. For example, a Smart Host can
be mounted next to a PAV-AIM7C. This rack is compatible with all
standard 19-inch National Electrical Manufacturers Association (NEMA)
rack mounts.
The instructions below show the RMB-PAVAM2F-xx, both brackets
install the same way they just face dierent directions.
1. Align the bracket with the Smart Host mounting points.
2. Attach using the screws provided with the bracket.
Network Configuration
For information on network requirements, refer to the Savant Device
Networking Guidelines on the Savant Community.Refreshing the IP Connection
After connecting to a new network, changing routers, or if the IP
Address range in the router was changed, the IP connection should be
refreshed. To refresh the IP connection, do one of the following:
–Hot Plug the Ethernet (LAN) Connection
–Cycle power
Savant® Smart Host Rack Mountable (SHR-2000)
Quick Reference Guide

SHR-2000 Quick Reference Guide | 009-1909-03 45 Perseverance Way, Hyannis, MA 02601
Copyright © 2021 Savant Systems, Inc. | 210611 2 of 2 Savant.com | 508.683.2500
Control Connections
RS-232 Wiring
Pin 1: No Connection Pin 5: RXD (Receive)
RJ-45 Connector
(Gold pins facing up)
Pin 1 Pin 8
Pin 2: No Connection Pin 6: TXD (Transmit)
Pin 3: No Connection Pin 7: CTS (Flow Control)
Pin 4: GND (Ground) Pin 8: RTS (Flow Control)
IMPORTANT NOTES!
–Wire colors are included to identify the pins used for this
connection. Colors shown do not represent any wiring standard.
–When wiring, DO NOT connect any wires within the cable that are
not required for communications.
–Pins 7 & 8 are only required for CTS/RTS handshaking.
–CTS/RTS handshaking is supported for flow control based on the
profile used in the Blueprint configuration.
–RS-422/485 is not supported
–Refer to the RS-232 Conversion to DB9 and RS-422/485 Pin-out
Reference Guide on the Savant Customer Community for more
information on RJ-45 to DB9 adapters oered by Savant.
Relay Wiring
Both Normally Open
and Normally Closed
outputs are available.
Pin 1: NC
(Normally Closed)
32
1
NC NOC / /
Pin 2: Common
Pin 3: NO
(Normally Open)
GPIO - General Purpose Input/Output
–GPIO’s configured
as an output can
be used to trigger
an action within
the system such as
switching a device.
–GPIO configured
as an input can
detect a state
change and trigger
a workflow.
Pin 1: GND (Ground)
32
1
GPIO 1
Standard
GPIO Using
PD Jumper
Gnd
I/O
PD
Pin 2: GPIO 1
Pin 3: PD (Pulldown)
–GPIO pins configured as an input are pulled high to (+12V) during
the boot process. To force the GPIO signal low during a boot-up,
connect the PD pin to the GPIO pin. This forces the GPIO output to
(< 0.8V) during the processor boot times.
IR Wiring (Infrared)
–Ensure that all IR
emitters are within 15
feet (4.6 meters) from
the controller’s location.
–Use of 3rd party
flashing IR emitters
with Talk Back is not
recommended. These
types of emitters can
draw voltage away from
the IR signal that can
degrade IR performance.
Pin 1: IR 1 -
1
IR1
+-+-+-
2
IR2
3
IR3
4 5 6
Use White Stripe
for Positive (+)
Pin 2: IR 1 +
Pin 3: IR 2 -
Pin 4: IR 2 +
Pin 5: IR 3 -
Pin 6: IR 3 +
–IR connections IR4 to IR6 (not shown in diagram) follow the same
wiring as connections IR1 to IR3.
Rear Panel
Reset
Ethernet USB
Audio
RS232-1 RS232-2
1
-+ +
IR
-2+
-3
Relay
CNC NO
4
-+ +
5
-6 -+
GPIO
1G PD
5VDC
IHG
FEDC
BA
AReset
Hold Reset Button for 5 seconds while powered
on to clear network settings. Status LED will
rapidly blink red when reset is complete.
B
USB Not Used
CAudio
Digital optical audio (TOSLink) input. Supports
up to 192kHz/24-bit digital audio in; PCM stereo
format only.
D
RS-232
8-pin RJ-45 female.
Used to transmit and receive serial binary data to
and from serial controllable devices.
Ports 1-2 RS-232 - CTS/RTS handshaking. CTS
RTS handshaking availability is based on the
component profile.
See RS-232 Wiring section for pin-outs.
E
IR
6-pin Screw Down Plug-in Connector. Used to
send IR signals to control devices with an IR input
or IR receiver via an IR flasher (5V tolerant only).
See IR Wiring section for important precautions
regarding IR functionality before making
connections.
F
Relay
3-pin Plug-in Connector. See Relay Wiring
section for pin-outs.
Normally Open (NO) / Normally Closed (NC) to
control devices requiring basic on/o operation.
DC Voltage Max: 30V DC 1A
G
Ethernet
8-pin RJ-45 female.
100 Base-T auto negotiating port. Connecting to
this port will disable Wi-Fi settings.
HGPIO
3-pin Plug-in Connector. See GPIO Wiring section
for pin-outs.
GPIO Input - When configured as an input, the
processor will look for a low (<0.8V DC) or a high
(>2.4V DC) state. Minimum 0V DC / Maximum
12V DC.
GPIO Output - When configured as an output,
the port provides a binary output of 0-12V DC
150mA max.
I5V DC
5V DC 3A - Connect included wall wart power
supply between the 5V DC connection and a 115-
240V AC surge protected outlet.
Further Product Information
To view available documentation, detailed product specs, and more:
–Visit the Savant Knowledge tab via the Savant Customer
Community to search all Savant documentation.