Savvier Fitness Booty Kicker BK200 User manual

CAUTION! READ ALL INFORMATION BEFORE USE.
SERIOUS INJURY OR FATALITY MAY OCCUR
- e Booty Kicker is not a toy. Keep out of reach of children.
- Always check with your physician before starting this or any exercise program.
- Do not use the Booty Kicker for anything other than its intended exercise purpose.
Use only as shown, illustrated and intended.
- Do not attempt any type of gymnastic movements on the Booty Kicker.
- Always inspect the Booty Kicker before every use for loose screws, nuts or damage. Tighten any screws or nuts prior to use. If you nd
any cracks or damage, then discontinue use immediately.
- Only use the Booty Kicker on a clean level surface making sure you have adequate clearance around the Booty Kicker for performing the
exercises.
- When using the Booty Kicker, only engage your hands, arms, legs, or feet with the wooden barre. e metal uprights and base legs are
not intended to be used as gripping or exercise surfaces.
- Similarly, when using any type of resistance band with the Booty Kicker, engage the band only with the wooden barre. Do not allow
bands to contact sharp objects. Be sure to inspect any resistance bands before use and discontinue use if any signs of nicks or tears.
- When rst attempting any exercise, use caution while determining your physical limitations. When performing any exercise involving
pushing or pulling forces on the barre, use caution to assure such forces do not create an instability causing either you or the barre to tip
over. Placing hands (or in the case of a resistance band) towards the middle of the wooden barre increases stability.
- Placing weights in the weight racks increases the Booty Kicker stability for performing certain pushing/pulling exercises. Removing
weights during exercises reduces the unit stability.
- Be sure to wear appropriate exercise clothing.
- Always properly store the Booty Kicker indoors aer use. e Booty Kicker could pose a hazard to children and pets, and should not be
le unattended. Store out of reach of children when not in use.
- Use caution when folding, as hinges may pose pinch points for ngers, hands, feet and toes. When the Booty Kicker is in the folded
position, always secure base legs and uprights together with the two Velcro straps. Weights should be removed from weight racks when
moving / transporting the Booty Kicker.
Use and Assembly Instructions
Video instructions can be found at www.BootyKicker.com/Instructions
Congratulations on receipt of your Fitness Barre. e innovative patent
pending design will provide you with great Barre tness workouts that will
kick your booty, tighten your abs and tone your entire body.
Assembly Steps:
Assemble on a hard, at, level surface (not carpet or rug). Carefully unpack and familiarize yourself with each component, assembly, hardware
and tools. Remove the Base Rod and two Cross Rods shipped inside the Upright Bar and the Leg Assemblies.
Step 1
• Place the two Leg Assemblies at on the oor with the Acorn
Nuts facing outward.
• With the Leg Assembly still in the folded position. Place the two
identical Cross Rods into the holes of the Upright Bars, as shown
in Fig.1. Secure with four Acorn Nuts, forming an X between
the Upright Bars. (Hand tighten only) Note the Top Cross Rod
overlaps on top of other Cross Rod as shown
• Place the Base Rod between the Leg Assemblies and into the
holes shown in Fig1, Secure with two Acorn Nuts. (Hand tighten
only)
• Place each Folding Gusset into the holes on the Base Bar, as
shown in Fig.1. Secure with two Acorn Nuts. Important, Acorn
nuts face outward. (Hand tighten only)
An innovation powered by Savvier Fitness
Step 2
• Holding the Base Leg in place, rotate the Upright Bars to
approximate position. As shown in Fig.2
• While holding the Upright Tube in place, Rotate a Folding Gusset upward. Holding the end of the Folding Gusset, gently ex the end outward.
Aligning the open end of the Folding Gusset and hole on the Upright Bar. Gently release the Folding Gusset completely through the Upright Bar
hole. As shown in Fig.2. Repeat on the other side of the assembly.
• Place the Straps onto the Gusset Rods. While holding the unit in place, gently pull outward on a Gusset Rod and rotate to place the rst hole of
the Strap onto the Gusset Rod. Important. Assemble the Strap with the hook or scratchy side of the Velcro facing upward. As shown in Fig.2. Do
not wrap the Strap yet.
Wooden Barre
Folding Gusset
Strap
Bracket
Weight Rack
Assembled Unit
Stretch Sleeve
Upright Bar
Base Leg
Folding
Acorn Nuts
Base Rod
Step 1
FIG.1
Leg Assembly
Cross Rods
Gusset Rods
Acorn Nuts
Remove
Cross Rods & Base Rod
Top Cross Rod
Base Rod
copyright 2019 Savvier Fitness LLC
191202
BK200

Step 5
Weight Racks
•Assemble the optional identical Weight Racks with the weight openings facing upward.
Align the three holes of the Weight Stack to the Upright Bar, as shown in Fig.4. and
insert three Allen screws per side.
• Assure that the Weight Rack part is clear of the Base Leg. Tighten each Allen screw
• Place weights onto each Weight Rack, placing the heaviest dumbbell at the bottom.
Folding
• Unwrap the Strap from each side of the fully assembled Barre
• While holding the Barre securely, gently pull outward on a Gusset and fold the
Gusset downward. Repeat on the other side and fold the unit downward to meet
the Base Bar. As shown in Fig.6
• On each side, wrap the strap around both bars and secure the Velcro
• e folded Barre Assembly may be lied and rolled. Weights should be
removed prior to moving or transporting the Barre Assembly.
Step 4
• Be sure your Booty Kicker is on a at level surface. Placing light downward
force on the Wooden Barre, check that all four corners of the assembly
are sitting at on the oor. If the unit does not sit at or rocks, then while
standing at the Barre, carefully apply downward and side to side force until
the unit is resting at.
• Using the Tool provided, partially tighten the eight Acorn Nuts of the Cross
Rods, Base Rod and Folding Gussets. Alternating sides as you tighten.
• Wrap the Strap two times around the Upright Bar, engaging the two
remaining holes of the Strap with the open end of the Gusset Rod and secure
the Velcro. Repeat for the Strap on the opposite side.
• Check again the assembly is sitting at. If not at, then slightly loosen the
Acorn Nuts and repeat the downward, side to side adjustment process. Once
the unit is sitting at, tighten the six Allen head screws around the Brackets.
en fully tighten the six Acorn Nuts of the Cross Rods and Base Rod. To
allow folding, gently tighten the Gusset Acorn Nuts. Conrm unit is sitting
at and if needed repeat the loosen / adjustment / tighten process.
• Place the Stretch Sleeve onto the Full Assembly, one side at a time. Align
the Sleeve between the Cross Bar Acorn Nuts with the seam of the Sleeve
between the Cross Bar Acorn Nuts and the seam of the Sleeve at the Upright
Bar. As shown in Fig.5
FIG.5
Stretch Sleeve
Seam
Folding
- Unwrap Strap. Gently pull
Gusset outward and fold
downward.
FIG.6
Step 4
Strap
Stretch Sleeve
Weight Rack
Partially
Tighten
Partially
Tighten
FIG.4
Step 3
• Place the Brackets, in the same orientation, onto the Wooden Ballet Barre,
as shown in Fig.3. Place an Allen head screw through the Bracket and into
the threaded insert on the Wooden Barre. Repeat on the opposite side. (Hand
tighten only)
• Place the Wooden Barre with assembled Brackets into the open top of the
Upright Bar. Noting the dierent hole locations. Gently squeezing the ends of
the Brackets, place the long end of the Bracket into the Upright Tube on both
sides, rst. And then insert the shorter ends of the Brackets to align with all four
holes of the Upright Bar. As shown in Fig3. Insert four Allen head screws into
the holes. As shown in Fig.3 Detail. (Hand tighten only)
Step 3
FIG.3
Detail
Bracket
Wooden Barre
Step 5
Folding
Gusset
Step 2
FIG.2
Up Right Bar
Velcro Hook
Fabric- Upward
Strap
Base Leg
copyright
2019 Savvier Fitness LLC
191202