Sawgrass R800 Quick Connect II User manual

Page 1
R1800 Printer Setup Instructions
Please read this document thoroughly before installing the
system to prevent voiding your warranty.
Check to ensure you have all components shown in picture.
1. Ink Cartridge + tubes
2. 1 x Long Tube Grip
3. 1 x Short Tube Grip
4. Chips
5. 8x Ink Bags
6. Small primer bottle
7. Cartridge Cover (Used R1800 Only)
8. Cartridge placement sticker
9. Rubber Gloves
10. Ink Box
11. Foam Block used for R800 only (Not Shown)
12. Power Driver CD (Not Shown)
1. Insert the ink bags into
the ink box by clipping
them into the connectors
inside the box. Each sec-
tion is marked with which
color ink should be placed
there.
1. Turn the printer on and press the
cartridge replacement button. 2. The cartridge bay will shift into the remove position. Remove any
installed cartridges.
3. Remove the cartridge cover by gently pushing on the right side and twisting it
to the right.
2. Use the priming bottle
to prime each line. To do
this, squeeze the priming
bottle to release all the
air then insert it into the
bottom of the cartridge to
prime the line and fill it
with ink. Do this for each
cartridge.
4. Apply cartridge placement
sticker over the existing one on the
cartridge bay.
5. Install the cartridge chips as shown above. Start by lining up the chip with the yellow dot with the yellow ink slot in the
cartridge bay. Next line up the chip with the black dot with the black slot in the cartridge bay. Finally insert the plastic
cross bars into place by sliding the notched end into the back of the chip holders.
6. Move the cartridge bay to the left of the gray bar
before installing the cartridges. Attach the cartridges
in this order .
(from left to right) -
Yellow, Magenta, Cyan, Light Cyan, Black, Red,
Blue, Light Magenta
7. When all cartridges are in place, attach the custom cover. When closing the cover be careful not to
pinch the tubes.
R800/R1800 Quick Connect Installation Instructions
For more detailed instructions please refer to the Epson R800/
R1800 Getting Started Guide or the Video Installation Guide on
your PowerDriver XG8™ CD

Page 2
1. Apply cartridge placement sticker
over the existing one on the cartridge
cover.
8. Place the large tube holder in the middle of the
gray bar and attach it to the printer. 9. Attach the short tube holder to the right of the printer where the tubes hang down. 10. Congratulations you have successfully in- stalled a R1800 Quick Connect II ink system.
R800 Printer Setup Instructions
2. Install the cartridge chips as shown above. Start by lining up the chip with the yellow dot with the yellow ink slot in the
cartridge bay. Next line up the chip with the black dot with the black slot in the cartridge bay. Finally insert the plastic
cross bars into place by sliding the notched end into the back of the chip holders.
4. Attach the long tube holder to the printer
on the top left hand corner next to the ink
symbol.
3. Gently slide the cartridges through the hole
in the cartridge cover. Start with the yellow
cartridge on the left and attach the cartridges in
this order: .
(from left to right) -
Yellow, Magenta, Cyan, Light Cyan, Black,
Red, Blue, Light Magenta
5. Attach the short tube holder to the right
of the printer where the tubes hang down.
6. Congratulations you have successfully installed
a R800 Quick Connect II ink system.
Tips:
• Make sure you install Power Driver XG from the CD that came
with your Quick Connect II system. Refer to the Power Driver
XG documentation and video tutorial on how to use Power
Driver XG.
• Perform a nozzle check from Power Driver XG. A few cleanings may be neces-
sary to get a good nozzle check.
• You may want to remove the printer lid or leave it open at all times.
• You may have a little air in your lines but this will clear after a few prints.
• If you are going to leave your system without using it for several days you should
clamp your lines with the tube clamps.
• Do not raise the ink box higher than the printer.