SCANMASKIN BURNISHER SX User manual

SCANMASKIN
BURNISHER SX
MANUAL

www.scanmaskin.com
2
Dear Customer!
ank you for choosing Scanmaskin as your supplier.
We wish you all the best with your new Scanmaskin Burnisher SX
and hope that it meets your expectations.
Per-Anders Bardh
CEO
Address:
Scanmaskin Sweden AB
Box 187
SE-437 22 Lindome /
Gothenburg Sweden
Telephone: [phone]
Fax: [phone]
www.scanmaskin.com
Scanmaskin Sweden AB

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 3
Table of content
1. Unit Assembly 4
2. Optional Upgrades 5
3. Engine Assembly 6
4. Deck Assembly 8
5. Tensioner Assembly and Engine Pulley Assembly 9
6. Front End Assembly 10
7. Pad Driver Assembly 11
8. Shroud Assembly and Shroud Bolt & Spring Asm. 12
9. Bottle Carrier Assembly 13
10. Tee Handle Assembly 14
11. Electrical Components 15
12. Clutch System and Operator Presence System 16
13. Metal Pad Driver Assembly 17
14. Labels & Literature 19
15. Wiring Schematic 20
16. Warranty 21
17. Contact Information 22

www.scanmaskin.com
4
1. Unit Assembly

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 5
2. Optional Upgrades

www.scanmaskin.com
6
3. Engine Assembly

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 7

www.scanmaskin.com
8
4. Deck Assembly

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 9
5. Tensioner Assembly and Engine Pulley Assembly

www.scanmaskin.com
10
6. Front End Assembly

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 11
7.Pad Driver Assembly

www.scanmaskin.com
12
8. Shroud Assembly and Shroud Bolt & Spring Assembly

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 13
9. Bottle Carrier Assembly

www.scanmaskin.com
14
10. Tee Handle Assembly

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 15
11. Electrical Components

www.scanmaskin.com
16
12. Clutch System and Operator Presence System

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 17
13. Metal Pad Driver

www.scanmaskin.com
18

SCANMASKIN BURNISHER SX ENGLISH
www.scanmaskin.com 19
14. Labels & Literature

Notes: * (Asterisk) indicates component is optional.
Ground points
1. Engine Block (Rear Bolt) 2. Engine Block (Near Voltage Reg.)
3. Muffler
4. Engine Block (Through Starter Solenoid Mounting) 5. Engine Block (Through Starter Mounting) 6. Common Circuit Board Ground Color Codes: BK = Black WT = White
RD = Red
BN = Brown
YL = Yellow
GY = Gray
GN = Green
GN/YL = Green + Yellow
BL = Blue
RD/WT = Red + White
W10550 Rev D 20171218 SJA
Wiring Schematic - X Series Machine
D2
D3
Relay 2 Relay 1
Fuse 3 6A
Used for Pump Water System
Fuse 1 6A
Fuse 2
3A
C1 C2
C3
C4 C5
D4
R1
R2
Adj
V outV in
U1
D5
D6
10 Pin
Connector
5 Pin
Connector
Circuit Board
1 2 3 4 5 6 7 8Emission
Module*
Black connects to OPS
when no Emission Module
Optional:
Operator Presence
Configuration
(Blue is
disconnected)
RD
RD
BK
BK
RD
BK
BL
RD
RD
RD
RD
RD
GY BL GN/YL WT YL
WT
BK
BK
BK
RD
YL
GN/YL
BK GN RD/WT
RD/WT
BL BK
BKBK
BK
BK
BN RD
RD
GY
RD RD
RD
RD
RD
BK
1
BN
WT
GN
YL
BK
BK
BK
GN
BL BK
Oxygen
Sensor*
Propane Solenoid Valve “Lockoff”
Starter
Solenoid
Key Switch
Run = B+R
Start = B+S
OFF = G+M
Magneto
D7
Voltage
Regulator
Battery
Starter
Motor
Oil
Pressure
Switch
USB
Port*
Clutch Handle Switch*
Electric Clutch*
Headlight
Switch*
LED Headlight 3Wx6 Floodlight
Water Switch*
RD
Water
Solenoid Valve*
1
1
1
2
2
3
1
1
4
66
5
6
6
6
6
6
6
B
S
R
G
M
GY
WT
GN
YL
BK
RD
1 2 3 4 5 6 7 8 9
10
BN
YL & BN are optional to extend
battery life of tach/hour meter
YL
RD
Tach /
Hour
Meter
Spark Plug
Wire 1
www.scanmaskin.com
20
15. Wiring Schematic