Schatten Design Dualie Inside’R User manual

Fig 1 Fig 2
Handmade Pickups For Acoustic Instruments
Dualie Inside’R Pickup Installation Instructions For Guitars and Ukuleles
For Guitars To install the Dualie Inside’R you will need the following tools:
Drill, 3/16", 3/8", and 31/64 drill bits, fluted burr, needle nose pliers.
Installing the Endpin Jack
1) Slack off all strings. Remove or tape out of the way the B,G,D, and A strings
leaving the high E and low E in place. Remove any end pin at the butt of the
guitar.
2) Drill a pilot hole through the end block approximately 3/16" in diameter in
the area you wish to place the end pin jack.
3) Using a fluted burr, chamfer the edges of the hole so that you will not
damage the finish of the instrument when you use the larger sizes of bits
required.
4) Drill through the guitar end block using a 3/8" bit and re-chamfer the hole.
Repeat using the 31/64" drill bit to complete.
5) Remove the outer strap button and the small nut and washer from the
endpin jack.
6) Place the Dualie inside the guitar and reach inside the sound hole and poke the endpin jack through the drilled hole in
the end block. The jack should protrude approximately 5/16" outside the guitar. Reinstall the flat washer and small nut.
7) Insert a small allen wrench or other small round (like a drill bit) through the 2 holes in the end of the endpin jack to
keep the jack assembly from rotating; tighten the small nut.
Installing the Pickup Pickup Placement For
Steel String Guitars:
1) As shown in figures 1
and 2, the exact
placement of the pickup
can vary.
2) Take some of the
inside putty supplied with
the pickup and roll and
knead the putty in your
fingers to soften it up.
Apply it evenly to the
face of the pickup (this is
the side with no label on
it) that will contact the
sound board of the
instrument. Please note
that we supply much
more putty than you will
actually need to use in installing the pickup. A proper layer of putty on the pickup will 1/16" thick.
3) Insert your hand through the sound hole of the guitar and starting with a placement on the treble side of the X brace,
press and slightly wiggle the pickup into place on the soundboard. Retune the E strings that were left in place. Plug the
guitar in and see what it sounds like (remember, you have the outside E strings on and can get a pretty good idea of
what the response is like).
4) Try the sound out along the X brace in the several positions that you have available and then try moving the pickup to
the bass side of the X brace and repeating checking for the best sound. Note that some instruments will have a physical
‘out of phase-ness’ that might show up with the pickup on one side of the instrument. Moving the pickup to the other
side will generally alleviate this.
627 Colby Drive, Waterloo Ontario, Canada N2V 1B4
www.schattendesign.com email: [email protected]
519-742-3862 toll free: 877-633-0177 fax: [phone]

Fig 3 Fig 4
Tests have shown that in
general, the best sound on
most acoustics will have the
pickup installed outboard of
the X braces. Placement can
and will vary from one
instrument to the other. Some
will sound best with the
pickup on the bass side (as
shown in fig 1)
Other guitars will sound best
with the pickup installed on
the treble side of the top.
Notice that the Pickup may
prefer to be placed anywhere
along the X, even between the finger braces ( fig 2).
Figures 3 and 4 show some alternate placements for the pickup. Some instruments will have better sound and fullness
with pickup mounted below the bridge plate as shown.
Pickup Placement For Classical Guitars
Pickup placement on a classical will be generally in the area of the bridge; usually biased towards the bass side of the
instrument. Sometimes it will sound best above the bridge towards the sound hole rather than below the bridge. You will
have to experiment a bit to find the ‘sweet spot’ for the pickup.
Dualie Inside’R Pickup Installation Instruction For a Ukulele
Follow steps 1 through 7 of Installing the endpin jack in the Guitars section.
a) Take some of the inside putty supplied with the pickup and roll
and knead the putty in your fingers to soften it up. Apply it evenly
to the face of the pickup (this is the side with no label on it) that
will contact the soundboard of the instrument. Please note that we
supply much more putty than you will actually need to use in
installing the pickup. A proper layer of putty on the pickup will be
1/16" thick.
b) Insert your fingers through the sound hole of the uke and press
and slightly wiggle the pickup into place on the soundboard. Most
ukes will have a brace going across the instrument just below the
sound hole and another brace going across below the bridge. You
will install the pickup centered on the soundboard about three or
four inches below the sound hole toward the bridge (this is about
as far as one’s fingers can reach inside) in the area between the
two braces.
Warranty
We warrant to the original purchaser that our pickups are free from defects in materials and workmanship for a period of 2 (two)
years. Should a product fail to perform properly within the specified warranty period you may contact your dealer or Schatten Design
for instructions. No product will be accepted for warranty return by Schatten Design without a Return Authorization number.
Rev. 07-09