Scheiber LIGHT AIR SWITCH Installation manual

Domotique embarquée
Embedded home automation
SCHEIBER
Bellevue, 85120 Saint-Pierre du Chemin •France
Tél : [phone] •[email protected] •[email protected] •www.scheiber.fr
Domotique embarquée
Embedded home automation
Marinebeam LED Lighting
660 Riverland Dr, Ste B
Charleston, SC 29412
[phone]
1
2
4
5
6
7
8
Start-up instructions
LIGHT AIR SWITCH
Description
Characteristics
Lighting Control Module x1
2.4 Ghz Antenna module x1
CAN cable (1m) x1
120 Ω terminations x2
2-way PicoMax connectors x8
6-way PicoMax connector x1
white 1-button switch x1
white 2-button switch x1
1
2
3
4
5
6
7
8
3
LIGHTING CONTROL MODULE 2.4 GHZ ANTENNA MODULE SWITCH
REFERENCE 41.72119.XX XXXXXX 41.72120.XX XXXXXX 68.INT221-2.4 68.INT222-2.4
POWER SUPPLY 8-32V DC witch CAN cable - 12VDC Kinetic energy
INPUTS Up to 4 digital inputs for wired switches
npn type
OUTPUTS 6 outputs - -
MAX.CURRENT PER OUTPUT 5A - -
TOTAL MAX. CURRENT 20A/module - -
DIMMING Light intensity regulation on each output with
PWM - -
SUPPLY & OUTPUTS WIRE CROSS SECTION 0.2 to 2.5mm²
CODING & INTPUTS WIRE CROSS SECTION 0.2 to 1.5mm²
MAX. NUMBER OF PAIRING
128 (up to 4 pairings on a 2-button switch)
Up to 32 2-button switches / 64 1-button
switches
- -
CONNECTORS
BUS CAN type 6-way Micro-Fit
2-way PicoMax outputs
6-way PicoMax inputs and coding
BUS CAN type 6-way Micro-Fit
Scheiber v8.0 Multibloc Protocol -
ANTENNA -PCB antenna PCB antenna
FIRMWARE VERSION -8.00 or higher -
NUMBER OF BUTTONS - - 1 2
TRANSMISSION RANGE -20m indoor 20m indoor
RADIO STANDARD
/ DEFAULT RADIO CHANNEL -2.4 Ghz IEEE 802.15.4 channels 11 … 26 / IEEE 802.15.4 radio channel 11
2.4 Ghz IEEE 802.15.4 channels 11 … 26
/ IEEE 802.15.4 radio channel 11
DEVICE IDENTIFICATION - - Individual 32 Bit Device ID (factory programmed))
SECURITY - - AES128 (CBC) with Sequence Counter
ENERGY BOW TRAVEL/FORCE - - 1.8 mm / typ. 10 N (at room temperature)
NUMBER OF OPERATIONS AT 25°C - - typ. 100.000 (tested according to EN 60669 /
VDE 0632)
CERTIFICATION CE CE CE
ENVIRONMENTAL CONDITIONS
Indoor use
Altitude up to 2000m
Operating temperature : 0 to +50°C
Humidity : 0 to 93% without condensation
Indoor use
Altitude up to 2000m
Operating temperature : 0 to +50°C
Humidity : 0 to 93% without condensation
-25°C to + 65°C
ELECTRICAL PROTECTION OF THE POWER LINE Fuse or circuit breaker
PROTECTION CALIBRE 16A if one power line in 2.5mm²
20A if two power lines in 2.5mm²
PROTECTION POSITION accessible and identied for the user
DIMENSIONS (LxWxH)110 x 77 x 26 mm 146 x 48 x 13.5 80 x 80 x 14.5 mm
MOUNTING DISTANCE width: 60mm
height: 100mm
vertical position : 50mm
horizontal position : 129mm
WEIGHT 0.120 Kg 0.150 Kg 0.06 Kg
Light Air Switch is the perfect solution to manage and transform the organisation of
your low voltage DC lighting.
The 2.4Ghz gateway included in this kit makes possible to use the wireless and battery-free
switches worldwide.
Kit contents :

SCHEIBER
Bellevue, 85120 Saint-Pierre du Chemin •France
Tél : [phone] •[email protected] •[email protected] •www.scheiber.fr
Domotique embarquée
Embedded home automation
Marinebeam LED Lighting
660 Riverland Dr, Ste B
Charleston, SC 29412
[phone]
• A long press (1.5sec) on the L key takes you into the set-up mode.
• Output 1 (S1) ashes, briey press the switch button you want to turn
output 1 ON, then press a second time the switch button you want to
turn output 1 OFF.
Case 1 : ON/OFF with 2 buttons
Case 2 : ON/OFF with 1 button
• Each press on the L key changes the activated output. The seventh press exits the set-up mode.
• If no action is taken for 2 minutes, the module returns to normal mode.
Pairing
ON
OFF
ON/OFF
• A long press on the L key : output 1 (S1) ashes
• A second press of the L key : output 2 (S2) ashes
• Briey press the switch you want to turn output 2 ON : output 2 is ON
• Briey press the switch you want to turn output 2 OFF : output 2 ashes again
An ON switch and an OFF switch are now allocated to output 2. You can continue to
allocate more switches to the same output by pressing them or you can move on to
setting up output 3 (S3) by pressing the L key.
EXAMPLE : ALLOCATION OF A SWITCH TO OUTPUT 2
C key (clear)
To clear a set-up output or the 6 outputs
of this lighting control module
• In set-up mode, (one of the module’s outputs
ashes), a long press on the C key clears the
setup of the selected ashing output.
• In normal mode, a long press (1.5 seconds) on
the C key clears the set-up of all the outputs of
this module.
Note: It is also possible to remove one switch from
an output (without clearing the other switches
associated with that output). To do this, select the
applicable output with the L key on the module.
Then, when the output ashes, press the switch
you want to remove until the output starts ashing
again after having been o for 1 or 2 seconds.
L key (learn)
To get into set-up mode and
change the activated output
LC
S4
S3
S2
S1
S5
S6
Wiring diagram
2.4 Ghz
120 Ω terminaison
CAN cable
S4
S3
S2
S1
S5
S6
8-32V DC Battery
2.4 Ghz
120 Ω terminaison
CAN cable
S4
S3
S2
S1
S5
S6
DC
AC
230V AC 8-32V DC power supply
Installation instructions
• This device must be located in a ventilated place to avoid the risk of water spatter.
• Do not install on heat-sensitive supports as carpet, PVC oor, etc...
• Imperatively install the product in a cool and dry place.
Markings used
Symbols Description
V Volt
A Ampere
Kg Kilogram
DC or Direct current
NOTE: 2.4 Ghz antenna module has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference’s by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
According §15.21 of the CFR 47- FCC part 15:
Any changes or modications to this equipment not expressly approved by the responsible party may cause, harmful interference and
void the FCC authorization to operate this equipment.
Up to 16A, you can only use one output (1-2 or 3-4).
Beyond, the power supply must be doubled (1 to 4).
Fuse 10-20A