Schiller FRED easyport plus Trainer User manual

FRED®easyport® plus Trainer
Automated external defibrillator (AED)
Depth 5.0cm
Rate 101/min
CPR OK CPR
00:59
User Guide
Art. no.: 2.511452 Rev. a *2.511452*

Sales and service information
The SCHILLER sales and service centre network is world-wide. For the address of your
local distributor, contact your nearest SCHILLER subsidiary.
In case of difficulty, a complete list of all distributors and subsidiaries is provided on our
internet site:
http://www.schiller.ch
Sales information can also be obtained from:
[e-mail]
Manufacturer and responsible for the marking
SCHILLER AG Phone: [phone]
Altgasse 68 Fax: [phone]
CH-6341 Baar, Switzerland E-mail: [email protected]
Web:www.schiller.ch
Article no.: 2.511452 Rev. a
Issue date: 2023-02-05
Corresponds to: original
Software: 1.2.2

Page 3
User Guide
FRED®easyport®plus Trainer
Art. no.: 2.511452 Rev. a
Table of Contents
1 Safety Notes .............................................. 5
1.1 Intended Purpose ................................................................. 5
1.2 Contraindication ................................................................... 5
1.3 Responsibility of the User ................................................... 5
1.4 Safety-Conscious Operation ............................................... 5
1.5 Maintenance and Cleaning .................................................. 6
1.6 Additional Terms .................................................................. 6
1.6.1 Terms of Warranty ............................................................................. 6
1.7 Symbols/Indicators .............................................................. 7
1.7.1 Symbols used in this user guide ........................................................ 7
1.7.2 Symbols used on the device .............................................................. 8
1.7.3 Symbols used on the training electrode packaging............................ 9
2 Components and Operation .................. 10
2.1 General Information ........................................................... 10
2.1.1 Configurations via Simulation App ................................................... 11
2.1.2 Configurations on the FEP+ TRAINER............................................ 12
2.2 Operating and Display Elements ...................................... 15
2.2.1 Overview FEP+ TRAINER ............................................................... 15
2.2.2 FRED easyport plus TRAINER with bag (optional).......................... 16
2.3 Inserting the batteries ........................................................ 17
2.3.1 Switching device On and Off............................................................ 17
2.3.2 Device-smartphone pairing .............................................................. 18
3 Training ................................................... 19
3.1 Training procedure semi automated AED ........................ 19
3.2 Training procedure fully automated AED......................... 20
3.3 Training procedure manual AED mode ............................ 21
3.4 Training on thorax compressions (optional) ................... 23
3.4.1 Setup of the sensor.......................................................................... 24
3.5 Accessories and disposables ........................................... 26
3.5.1 Order Information............................................................................. 26
3.5.2 Required accessories....................................................................... 26
3.6 Disposal information.......................................................... 27
3.6.1 Battery Disposal............................................................................... 27
3.6.2 Disposal at the end of its useful life.................................................. 27
3.7 Troubleshooting ................................................................. 28
3.7.1 Troubleshooting ............................................................................... 28
3.8 Preventing electromagnetic interferences....................... 29
3.8.1 Measures to prevent electromagnetic interferences ........................ 29
4 Technical Data ........................................ 30
4.1 System Specifications ....................................................... 30
5 Appendix - Symbols ...................................

Page 4
FRED®easyport®plus Trainer
Art. no.: 2.511452 Rev. a

Page 5
Safety Notes 1
User Guide Intended Purpose 1.1
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
1 Safety Notes
1.1 Intended Purpose
The FRED easyport plus®TRAINER is a training device designed to train the
intended functions of the intended users in the intended environment of the
FRED easyport plus device.
Indication The FRED easyport plus®TRAINER is ONLY used for training and simulation
NOT for the use on a patient.
Intended user The FRED easyport plus®TRAINER is intended to be used for training purpose
of the same intended users as the FRED easyport plus device.
The following people may use the FRED easyport plus® Trainer:
• Anyone who wants to be trained in the application of an AED under supervision
and with instructions of a trainer.
1.2 Contraindication
1.3 Responsibility of the User
1.4 Safety-Conscious Operation
Limitations
No contraindications for the system known.
Contraindication for the patient
The FRED easyport plus®TRAINER is not indicated to be use for patient treat-
ment.
Damaged or missing components must be replaced immediately.
Properly dispose of the packaging material and make sure it is out of children's
reach
Do not store the training electrodes together with the normal electrodes or with
the normal defibrillator.
This user guide is only for the trainer and not for the trainee.
Immediately report any changes that impair safety (including operating behav-
iour) to the responsible person.
Only use original SCHILLER training electrodes.
Immediately replace a damaged unit, or damaged cables and connections.
Only operate the device in accordance with the specified technical data.

1 Safety Notes
1.5 Maintenance and Cleaning
Page 6
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
1.5 Maintenance and Cleaning
1.6 Additional Terms
1.6.1 Terms of Warranty
Your SCHILLER FRED easyport plus®TRAINER is warranted against defects in mate-
rial and manufacture according the general terms of condition. Excluded from this
warranty is damage caused by an accident or as a result of improper handling. The
warranty entitles to free replacement of the defective part. Any liability for subsequent
damage is excluded. The warranty is void if unauthorised or unqualified persons at-
tempt to make repairs.
In case of a defect, send the device to your dealer or directly to the manufacturer. The
manufacturer can only be held responsible for the safety, reliability, and performance
of the apparatus, and assume the warranty, if:
• assembly operations, extensions, readjustments, modifications, or repairs are
carried out by persons authorised by him,
• spare parts used for assembly operations, extensions, readjustments, modifica-
tions or repairs are recommended or supplied by SCHILLER, and,
• the SCHILLER FRED easyport plus®TRAINER and approved attached equipment
is used in accordance with the manufacturer's instructions.
Before cleaning, switch the unit off and remove the battery.
Do not use aggressive or abrasive cleaners.
Do not, under any circumstances, immerse the device or cable assemblies in
liquid.
There are no express or implied warranties which extend beyond the warranties here-
inabove set forth. SCHILLER makes no warranty of merchantability or fitness for a
particular purpose with respect to the product or parts thereof.

Page 7
Safety Notes 1
User Guide Symbols/Indicators 1.7
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
1.7 Symbols/Indicators
1.7.1 Symbols used in this user guide
The safety levels are classified according to ANSI Z535.6. The following overview
shows the safety symbols and pictograms used in this user guide.
The terms Danger, Warning, and Caution are used in this User Guide to point out poten-
tial dangers and to indicate risk levels. Familiarise yourself with their definitions and sig-
nificance.
For a possibly dangerous situation which could lead to severe personal injury or to
death.
For a possibly dangerous situation which could lead to personal injury. This symbol is
also used to indicate possible damage to property.
For general safety notes as listed in this section.
Important or helpful user information.

1 Safety Notes
1.7 Symbols/Indicators
Page 8
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
1.7.2 Symbols used on the device
General used symbols see 5 Appendix - Symbols.
Reading the instruction for use is mandatory before using the device!
Dangerous voltage! Used for electrical dangers during defibrillation.
IP44 The enclosure is protected against foreign solid objects of  1 mm and splashing
water from all directions
Cover battery housing replacement instruction
Bluetooth inside
Attention: non ionising electromagnetic radiation. Some of the devices contain an HF
transmitter (Bluetooth).
The FRED easyport plus®TRAINER radiates high-frequency electromagnetic energy
and can disturb other devices if not installed and operated in accordance with the us-
er guide. However, there is no guarantee that no interference can occur in certain
installations. If the FRED easyport plus®TRAINER causes interferences, these can be
determined by switching the device off/on or by transmitting/not transmitting ECG
data. The user can take the following measures to prevent electromagnetic interfer-
ences:
• Increase the distance between the disturbed device and the FRED easyport plus®
TRAINER A minimum distance of 20 cm must be kept between the device and a
pacemaker.
• Turn the device to change the angle of radiation.
For more details, see page 29.

Page 9
Safety Notes 1
User Guide Symbols/Indicators 1.7
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
1.7.3 Symbols used on the training electrode packaging
General used symbols see 5 Appendix - Symbols.
These electrodes are only intended for training, not for clinical use.
Do not store these electrodes with your normal defibrillator.
Reading the instruction for use is mandatory before using the electrodes!
Do not bend packing
Don’t use if the packaging is damaged
Disposable item; do not reuse
• Remove the patient's clothes
• Open the electrode packaging
• Peel off the protective foil
Storage temperature for the electrodes
Expiry date of the electrodes
An open package cannot be conserved more than one day.
The product is intended to be used on patients weighing 25 kg or more.
The product is intended to be used on patients weighing less than 25 kg.

2 Components and Operation
2.1 General Information
Page 10
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
2 Components and Opera-
tion
2.1 General Information
The FEP+ TRAINER is a simple and cost-effective simulator of the FRED easyport
plus®that is designed to be used exclusively for training.
Operating modes The operating mode can be selected by configuration. One device is enough to train
both the fully automatic, semi-automatic mode and Manual mode
• One scenario can be predefined and downloaded to the FEP+ TRAINER.
• Scenario can be changed live by using the Defi training application.
Languages All languages available on the FEP+ TRAINER are also available on the Trainer.
Language selection as well as scenario selection is done by configuration.
Standard package The FEP+ TRAINER standard package includes:
•1FEP+ TRAINER
• 1 set of training electrodes
• 1 training electrodes cable
• 9V battery
ARGUS LifePoint (optional) CPR feedback sensor for additional training on chest compression
The following instruction uses the Name FEP+ TRAINER instead of the full name
FRED easyport plus®TRAINER
The FEP+ TRAINER doesn’t deliver any energy, it simply plays through the resusci-
tation process with different scenarios. It is powered by a standard 9 V battery
The FEP+ TRAINER equipped with Bluetooth, identified by the symbol on the de-
vice label, can be controlled and configured via your smart-phone/tablet PC with the
“Defi training application” which can be downloaded from:
The FEP+ TRAINER provides simulation that aim to help to familiarise with the FRED
easyport plus®and shows that the users have the knowledge required to use it if nec-
essary.

Page 11
Components and Operation 2
User Guide General Information 2.1
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
2.1.1 Configurations via Simulation App
Configuration Values
Device
Simulation of the following device types:
Semi-automatic
Manual
Automatic
Normal
FEP+ Manual
FEP+ Auto
Audio language List of available language

2 Components and Operation
2.1 General Information
Page 12
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
2.1.2 Configurations on the FEP+ TRAINER
The following programming should be adapted for the organisation to be trained.
Note: This bold settings have been entered during the initial setting. The initial setting
screen appears only after the device is set to factory default.
For all settings please refer to the user guide of the FRED easyport plus
Access to the device setting menus:
Please note: This access code is only for the training organisation.
Configurable device parameters Detail see cross reference below or
IFU of the FRED easyport Plus
Password required
• Selftest -No
• Bluetooth pairing 2.3.2 Device-smartphone pairing No
• Device Settings >>>
– CPR settings >>>
– CPR feedback >>>
– Communication >>>
– Transmission mode >>>
Device Setting >>> CPR setting,
page 13
Yes
– System settings >>>
- Local settings >>> Language, Country, Time, Date, Time-
zone
- Volume settings
- ECG and HR display
– Restore Factory Defaults
Second page
– Import Settings
– Export Settings
–Trainer Device Variant
–First (Normal)
– Auto (FEP+ Auto),
– Manual (FEP+ manual)
This can be changed also via Simulation App but after power
cycling it will start with the programmed mode.
–Restore Default Scenario
(Electrode not applied, shock/no shock/ shock)
System Setting >>> Local setting,
page 14
Yes
To get access to the settings:
Press and hold the button while switching the device on .
The Configuration menu appears.
Enter the password ; ; for the Device setting menu.
Prev
OK
Next
Selftest >>>
Start
>>>
>>>
>>>
>>>
Configuration
Bluetooth pairing
Device information
Device Settings
Device Update
Pads Expired
>>>
Log Files
>>>
Production

Page 13
Components and Operation 2
User Guide General Information 2.1
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
Device Setting >>> CPR setting
Default settings are bold
Additional settings for the AED MANUAL
Device Setting >>> CPR Feedback
System Setting >>> CPR setting
Parameter Values Description
Start with Analysis •No
•Yes
If Yes is set, the device starts with the analysis as soon as defibrillation
electrodes are applied.
If No is set, the device prompts the user to perform CPR before the
analysis. Analysis will start once the 2-minute CPR interval has ended.
Show CPR Timer •No
•Yes Display of the CPR timer on the status line.
CPR Timer counting •Up
•Down Timer counting up or down
Metronome AED
•On
• Off
•CPR
Metronome default behaviour only for AED mode
Metronome Ratio
•30:2
•15:2
• Cont
Metronome Setting
Metronome rate •100 cpm
• 100-120 Sets the frequency of the metronome
Manual Settings >>>
Metronome MAN •On/Off / CPR Metronome default behaviour in manual mode
Metronome Ratio •30:2 / 15:2 / Cont Metronome Setting in Manual mode
CPR Voice Prompts •Yes
•No Voice prompt in manual mode yes or no.
Parameter Values Description
CPR Voice prompts •Yes
•No Yes activates the voice prompt during CPR
Parameter Values Description
Volume
• Low (>50)
• Mid (>55)
• High (>60)
Sets the volume of audio prompts and notifications.
Caution:
Ensure that the environmental noise is below the set sound volume
(Low/Mid/High)
ECG and HR •No
•Yes
Display HR and ECG curve (not displayed for the AED manual because
it is standard activated)

2 Components and Operation
2.1 General Information
Page 14
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
System Setting >>> Local setting
Note: This settings have been entered during the initial setting. The initial setting
screen appears only after the device is set to factory default.
Parameter Values Description
Language
•English* German
French Spanish Italian
etc…
Sets of the language in which the device will always start by default.
Country
•Other
• France, Germany, UK,
USA...
-
Date • - Sets the date
Time •- Sets the time

Page 15
Components and Operation 2
User Guide Operating and Display Elements 2.2
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
2.2 Operating and Display Elements
2.2.1 Overview FEP+ TRAINER
The picture below shows the user interface for an AED with ECG and CPR feedback
display.
Fig. 2.1 Operating Elements
(1) Green button to switch the device on/off and RTU LED (Ready -to-use LED)
Additionally the button is used to “Pause” the algorithm.
(2) Orange indicator lamp; lit as long as no electrodes are connected
(3) Electrode connector
(4) LCD screen
(5) Switching to child mode when using adult electrodes (PATIENT button)
(6) USB connector for Argus LifePoint sensor or USB memory stick
(7) Orange button: key to trigger a defibrillation impulse (SHOCK button)
(8) Battery at back
(9) Loudspeaker
(10) Microphone
(11) Data transfer (COM) button
(12) Ambient light sensor
The status LEDs are not active!
11
34
5
9
1
7
10
6
8
2
12 30 Chest compressions
then 2 rescue breaths
CPR OK Depth 5.0 cm
Rate 101 /min
CPR
00:59

2 Components and Operation
2.2 Operating and Display Elements
Page 16
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
2.2.2 FRED easyport plus TRAINER with bag (optional)
(1) RTU LED (Ready -to-use LED) transparent window
(2) Defibrillation electrode compartment
(3) Scissor and razor compartment
(4) Connection ARGUS LifePoint CPR feedback sensor (USB Port)
(5) ARGUS LifePoint compartment
5
9
1
8
3
2
4
1

Page 17
Components and Operation 2
User Guide Inserting the batteries 2.3
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
2.3 Inserting the batteries
2.3.1 Switching device On and Off
Switching ON Press the “ON/OFF” (1) button
Switching OFF Press the “ON/OFF” (1) button for 3 seconds.
Danger of explosion! The battery must not be exposed to high temperatures or
disposed of with household waste.
Do not short-circuit, cut, destroy, burn or charge a battery.
Replace the battery if the device indicates a battery problem. A defective battery
must not be used.
1. Open the battery cover by pressing the locking mechanism in the direction of the
arrow (1).
2. Lift up the battery, disconnect the cable and remove the batttery
3. Insert the new battery into the device as shown on the picture (2) and connect the
cable.
4. Close battery compartment with the battery cover.
1
2
Forced shutdown procedure
If the device cannot be switched off via the above procedure, remove the battery and
insert it again.
The running AED algorithm can by paused during CPR by the Green ON/OFF button
(press 1 second) and continued by pressing again the ON/OFF button.

2 Components and Operation
2.3 Inserting the batteries
Page 18
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
2.3.2 Device-smartphone pairing
Before the FEP+ TRAINER can be selected from the device list on the App (Step 9),
it must first be paired with the smart-phone
1. Press and hold the button while switching the device on .
2. The configuration menu is displayed.
3. Start Bluetooth pairing. The blue message bar shows bluetooth discoverable
(blinking Bluetooth icon).
4. Open on your smart-phone the menu Setting > Connected devices (bluetooth)
and select paring new device. The Name FEP+Trainer 9010.xxxxxx is displayed.
5. To pair the device with your smart-phone select the name and confirm the pairing.
6. If successfully paired with the smart-phone “Bluetooth paired” is displayed on the
device
7. Open the Schiller Defi training App on your smart-phone or tablet PC.
8. Select the icon the Device list of Defi training application. Select the de-
vice you want to use in the list.
For additional information on the application, refer to the application: Settings
> Application > Help.
Prev
OK
Next
Selftest >>>
Start
>>>
>>>
>>>
>>>
Configuration
Bluetooth pairing
Device information
Device Settings
Device Update
Pads Expired
>>>
Log Files
>>>
Production

Page 19
Training 3
User Guide Training procedure semi automated AED 3.1
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
3 Training
3.1 Training procedure semi automated AED
• The following instructions comply with the scenario “shock recommended” and
then twice shock not recommended. The scenarios can be selected and saved.
• The following procedure should be checked by the trainer:
– call emergency service dial number
– use only if patient is unresponsive
– remove clothes from upper body - cut if necessary
– tear open electrode package located in device packaging
– as shown on package peel off the packing and apply both electrodes to the up-
per body
Trainee starts by switching on the
device
As soon the connection to the App is established, you can press the electrode button
and then “Next Step on the App if the electrodes have been not right applied. This will
cause that the trainer starts with step 1.
1. Check that electrodes connector is correctly fitted in machinea
Trainer has to confirm correct per-
formance with the button on the de-
vice or via Defi training application
Trainer confirms that the above procedure was correctly performed by the train-
ee. Otherwise, the instructions step 1 is repeated. After the third repetition, the
instructions jump to step 8.
2. Do not touch the patient analysis will begin
3. Do not touch the patient analysing
4. Shock advised
5. Stand clear of patient
6. Press orange button - now (if shock button is not pressed within 20 seconds it
jumps to 8.)
7. Shock delivered
8. Advise to do chest compression: according to configuration
9. Repeat until next instruction (the next instruction starts with step 2)
– After the instruction “no shock advised” (step 4), it jumps to step 8.
Finishing resuscitation process To finish the resuscitation process and switch the device to standby mode, press
the Green ON/OFF button (press 3 second).
• As soon the FEP+ TRAINER is switched on, the voice prompt starts.
• Advise the trainee to follow the instruction from the device.
• The running AED algorithm can by paused during CPR by the Green ON/OFF but-
ton (press 1 second) and continued by pressing again the ON/OFF button
• Depending on the configuration the FEP+ TRAINER may start with Step 1 or 8
(see chapter 2.1.2 Menu Start with analysis Yes/No).
• When a scenario have been saved with the App the FEP+ TRAINER start with
Step 2, because the electrode status is set to electrode applied.
a. If FEP+ TRAINER start with Step 8, check configuration, if it starts with Step 2 set
the Scenario to Default in the Menu Device Setting > Restore Default Scenario.

3 Training
3.2 Training procedure fully automated AED
Page 20
Art. no.: 2.511452 Rev. a
FRED® easyport® plus Trainer
3.2 Training procedure fully automated AED
• The following not advices procedure from the device should be checked by the
trainer:
– call emergency service dial number
– remove clothes from upper body - cut if necessary
– tear open electrode package located in device packaging
– as shown on package peel off the packing and apply both electrodes to the up-
per body
Trainee starts by switching on the
device
As soon the connection to the App is established, you can press the electrode button
on the App if the electrodes have been not right applied. This will cause that the trainer
follows up with step 2.
1. Make sure the patient is unresponsive
2. Plug and apply the electrodes (repeated 3 times)
3. Check that electrodes connector is correctly fitted in machine
Trainer has to confirm correct per-
formance with the button on the de-
vice or via Defi training application
Trainer confirms that the above procedure was correctly performed by the train-
ee. Otherwise, the instructions step 3 is repeated. After the third repetition, the
instructions jump to step 10.
4. make sure the patient is unresponsive
5. Do not touch the patient analysis will beginb
6. Do not touch the patient analysing
7. Shock advised
8. Warning! Shock will be delivered
9. 3-2-1
10. Shock delivered
11. Advise to do chest compression: according to configurationc
12. Repeat until next instruction (the next instruction starts with step 4
– After the instruction “no shock advised” (step 7), it jumps to step 11.
Finishing resuscitation process To finish the resuscitation process and switch the device to standby mode, press
the Green ON/OFF button (press 3 second).
• The following instructions comply with the scenario “shock recommended” and
then shock not recommended.
• Depending on the configuration the FEP+ TRAINER may start with Step 1 or 11
(see chapter 2.1.2 Start with analysis Yes/No).
• When a scenario have been saved with the App the FEP+ TRAINER jumps from
Step 1 direct to Step 5, because the electrode status is set to electrode applied.
b. If FEP+ TRAINER jumps from Step 1 direct to Step 5, set scenario to Default in
the Menu Device Setting > Restore Default Scenario.
c. If FEP+ TRAINER start with Step 11, check configuration.