SCHMOTZER Venterra 2K KPP-LSC Quick guide

Translation of the original operating instructions
Hoeing machine
Venterra 2K KPP-LSC
Venterra 2K KPP-MSC
Venterra 2K KPP-M

Please enter the identication data of the implement. The identication data can be found on
the rating plate.

TABLE OF CONTENTS
1 About this operating manual 1
1.1 Copyright 1
1.2 Diagrams 1
1.2.1 Warnings and signal words 1
1.2.2 Further instructions 2
1.2.3 Instructions 2
1.2.4 Lists 4
1.2.5 Item numbers in figures 4
1.2.6 Direction information 4
1.3 Other applicable documents 4
1.4 Digital operating manual 4
1.5 Your opinion is important 4
2 Safety and responsibility 5
2.1 Basic safety instructions 5
2.1.1 Meaning of the operating manual 5
2.1.2 Safe operating organisation 5
2.1.3 Knowing and preventing dangers 10
2.1.4 Safe operation and handling of the
machine 13
2.1.5 Safe maintenance and modification 15
2.2 Safety routines 18
3Intended use 20
4 Product description 22
4.1 Implement overview 22
4.2 Function of the implement 23
4.3 Special equipment 24
4.4 Warning symbols 25
4.4.1 Positions of the warning symbols 25
4.4.2 Layout of the warning symbols 25
4.4.3 Description of the warning symbols 26
4.5 Lighting and identification for
road travel 29
4.5.1 Rear lighting and identification for
road travel 29
4.5.2 Front lighting and identification 29
4.6 Implement slide rail 30
4.7 Section Control parallelograms 30
4.8 Camera bracket 31
4.9 Hoe share 31
4.10 Rating plate on the implement 32
5 Technical data 33
5.1 Dimensions 33
5.2 Hoeing tools 33
5.3 Permitted mounting categories 33
5.4 Forward speed 33
5.5 Performance characteristics of
the tractor 34
5.6 Noise development data 34
5.7 Drivable slope inclination 34
6Preparing the machine 35
6.1 Calculating the required tractor
characteristics 35
6.2 Coupling the implement 38
6.2.1 Attaching the lower link ball sleeves 38
6.2.2 Attaching the top link ball sleeve 38
6.2.3 Driving the tractor towards the
implement 39
6.2.4 Coupling the hydraulic hose lines 39
6.2.5 Coupling the power supply 41
6.2.6 Coupling the ISOBUS lines 41
6.2.7 Coupling the 3-point mounting frame 43
6.2.8 Aligning the implement 43
6.3 Preparing the machine for road
travel 44
6.3.1 Removing the parking supports 44
6.3.2 Moving the hoe protection discs
into transport position 47
TABLE OF CONTENTS
MG7104-EN-II | E.1 | 15.09.2023 | © SCHMOTZER I

6.3.3 Moving the parallelograms into
transport position 47
6.3.4 Folding the implement 50
6.4 Preparing the implement for
operation 51
6.4.1 Unfolding the implement 51
6.4.2 Selecting the parallelograms and
moving them into working position 51
6.4.3 Setting up the support wheels 54
6.4.4 Aligning the parallelograms on the
rows 58
6.4.5 Adjusting the hoeing width 59
6.4.6 Adjusting the hoeing depth 61
6.4.7 Activating or deactivating the hoe
protection discs HSZ 62
6.4.8 Adjusting the hoe protection discs
HSZ 63
6.4.9 Adjusting the RowDisc hoe
protection discs 67
6.4.10 Activating or deactivating the finger
hoes 73
6.4.11 Adjusting the finger hoes 75
6.4.12 Adjusting the ridging tools 78
6.4.13 Activating or deactivating the tine
weeder 86
6.4.14 Adjusting the tine weeder 87
6.4.15 Setting the band sprayer 87
6.4.16 Adjusting the row sensor 91
7Using the implement 95
7.1 Using the KPP-LSC implement or
KPP-MSC implement 95
7.1.1 Using the implement 95
7.1.2 Turning on the headlands 96
7.2 Using the KPP-M implement 98
7.2.1 Using the implement 98
7.2.2 Turning on the headlands 99
8Eliminating faults 101
9 Parking the implement 103
9.1 Moving the parallelograms into
working position to park the
implement 103
9.2 Attaching the parking supports 104
9.2.1 Attaching the parking supports
when parking the folded implement 104
9.2.2 Attaching the parking supports
when parking the unfolded
implement 107
9.3 Uncoupling the 3-point mounting
frame 110
9.4 Uncoupling the ISOBUS lines 110
9.5 Uncoupling the power supply 110
9.6 Disconnecting the hydraulic
hose lines 111
10 Repairing the implement 112
10.1 Maintaining the implement 112
10.1.1 Maintenance schedule 112
10.1.2 Checking the hydraulic hose lines 113
10.1.3 Checking the lower link pins and
top link pins 113
10.1.4 Replacing Rapido duckfoot shares 114
10.1.5 Replacing RapidoClip duckfoot
shares 115
10.1.6 Replacing the Rotavator blade 116
10.1.7 Replacing finger hoes 117
10.2 Lubricating the implement 118
10.2.1 Overview of lubrication points 119
10.3 Cleaning the implement 121
11 Loading the implement 122
11.1 Loading the unfolded implement
with a crane 122
11.2 Loading the folded implement
with a crane 123
11.3 Lashing the unfolded implement 123
11.4 Lashing the folded implement 125
12 Disposing of the implement 126
TABLE OF CONTENTS
MG7104-EN-II | E.1 | 15.09.2023 | © SCHMOTZER
II

13 Appendix 127
13.1 Bolt tightening torques 127
13.2 Other applicable documents 128
14 Directories 129
14.1 Glossary 129
14.2 Index 130
TABLE OF CONTENTS
MG7104-EN-II | E.1 | 15.09.2023 | © SCHMOTZER III

About this operating manual 1
1.1 Copyright
Reprinting, translation and reproduction in any form,
including excerpts, require the written approval of
AMAZONEN-WERKE.
1.2 Diagrams
1.2.1 Warnings and signal words
Warnings are marked with a vertical bar with a
triangular safety symbol and the signal word. The
signal words "DANGER", "WARNING" or "CAUTION"
describe the severity of the potential danger and have
the following meanings:
DANGER
Indicates a direct threat with high risk for
severe physical injury, such as loss of
limbs or death.
WARNING
Indicates a possible threat with moderate
risk for severe physical injury or death.
CAUTION
Indicates a threat with low risk for light or
moderately severe physical injuries.
CMS-T-00000081-H.1
CMS-T-00012308-A.1
CMS-T-005676-F.1
CMS-T-00002415-A.1
1 | About this operating manual
MG7104-EN-II | E.1 | 15.09.2023 | © SCHMOTZER 1

1.2.2 Further instructions
IMPORTANT
Indicates a risk for damage to the
implement.
ENVIRONMENTAL INFORMATION
Indicates a risk for environmental damage.
NOTE
Indicates application tips and instructions for
optimal use.
1.2.3 Instructions
1.2.3.1 Numbered instructions
Actions that have to be performed in a specific
sequence are represented as numbered instructions.
The specified sequence of the actions must be
observed.
Example:
1. Instruction 1
2. Instruction 2
1.2.3.2 Instructions and responses
Reactions to instructions are marked with an arrow.
Example:
1. Instruction 1
Reaction to instruction 1
2. Instruction 2
CMS-T-00002416-A.1
CMS-T-00000473-D.1
CMS-T-005217-B.1
CMS-T-005678-B.1
1 | About this operating manual
Diagrams
MG7104-EN-II | E.1 | 15.09.2023 | © SCHMOTZER
2

1.2.3.3 Alternative instructions
Alternative instructions are introduced with the word
"or".
Example:
1. Instruction 1
or
Alternative instruction
2. Instruction 2
1.2.3.4 Instructions with only one action
Instructions with only one action are not numbered,
but rather shown with a arrow.
Example:
Instruction
1.2.3.5 Instructions without sequence
Instructions that do not require a specific sequence
are shown as a list with arrows.
Example:
Instruction
Instruction
Instruction
1.2.3.6 Workshop work
WORKSHOP WORK
Identifies maintenance work that must be
performed at a workshop that is adequately
equipped in terms of agricultural technology,
safety and environmental technology by
specialist personnel with appropriate training.
CMS-T-00000110-B.1
CMS-T-005211-C.1
CMS-T-005214-C.1
CMS-T-00013932-B.1
1 | About this operating manual
Diagrams
MG7104-EN-II | E.1 | 15.09.2023 | © SCHMOTZER 3

1.2.4 Lists
Lists without an essential order are shown as a list
with bullets.
Example:
Point 1
Point 2
1.2.5 Item numbers in figures
A framed number in the text, e.g. a
1
, indicates an
item number in an adjacent figure.
1.2.6 Direction information
Unless otherwise specified, all directions are always
seen in the direction of travel.
1.3 Other applicable documents
A list of other applicable documents can be found in
the Appendix.
1.4 Digital operating manual
The digital operating manual and e-learning can be
downloaded from the Info Portal on the AMAZONE
website.
1.5 Your opinion is important
Dear reader, our operating manuals are updated
regularly. Your suggestions for improvement help us
to create ever more user-friendly operating manuals.
Please send us your suggestions by post, fax or
email.
Fax: [phone]
Postfach 51
AMAZONEN-WERKE H. Dreyer SE & Co. KG
Technische Redaktion
D-49202 Hasbergen
E-Mail: [email protected]
CMS-T-000024-A.1
CMS-T-000023-B.1
CMS-T-00012309-A.1
CMS-T-00000616-B.1
CMS-T-00002024-B.1
CMS-T-000059-C.1
1 | About this operating manual
Other applicable documents
MG7104-EN-II | E.1 | 15.09.2023 | © SCHMOTZER
4