Schrack Integral MAP Owner's manual
Operating panel Integral MAP
Quick user manual
General operations
Normal operation
In an idle mode (standard indication), the display
shows product and customer information. The list
counters are set to 0. The Operation M LED in-
dicates the system’s current operating status.
Fault messages
The N LED flashes and the fault’s signal is sound-
ing, if there are faults (Chapter Reset alarm/fault sig-
nal). The list of faults Faults T displays the mal-
functioning component with element type, element
number and where applicable detector zone.
There may be an device or system fault or the
emergency mode has been activated.
Emergency mode
(fire alarm control panels Integral EvoxX C and In-
tegral EvoxX B)
If the error code xxx/29 is displayed for a fault in
the active system, emergency mode is activated.
Operating and indication functions are reduced; fire
alarm system functions. Call the service depart-
ment/customer service immediately (necessary in-
formation: equipment type and number, customer
number, messages, error codes).
Reset alarm/fault signal
Pressing the button Buzzer silenced D disables
the signal tone of an active alarm or fault message
in the fire alarm control panel; the LED remain lit
up. Any additional alarm or fault message will trig-
ger the alarm and fault signal tones again. Acknow-
ledgement and intervention signal tones cannot be
reset.
Delay
(Depends on programming)
Pressing the button Delay B activates or deactiv-
ates the delay function. During the delay period it is
for instance possible to activate the intervention
function. If delayed switching has been activated
(daytime program), then the button LED is lit, and
if the night program is activated, then the LED is
not lit (night program).
Disabling/actuating elements
(An authorisation code must be entered for this to
be permitted)
Pressing the button of the element type to which
the element belongs H. Enter the number of the
element to be selected using the numerical buttons
of the keypad I. Confirm with the enter button
D.
Pressing the button Off K turns the element off.
Pressing the button On J turns the element on.
Further element operation
Pressing the button of the element type to which
the element belongs H. Enter the number of the
element to be selected using the numerical buttons
of the keypad I. Confirm with the enter button
D.
Pressing the button Other Commands L dis-
plays the list of all available commands. Using the
scroll buttons E/F to scroll through all the
entries in the list. Confirm with the enter button
D.
WARNING
Triggering automatically controlled outputs by maintenance
If extinguishing systems or other critical fire alarm devices are automatically controlled via a
fire alarm control panel, then electrical, mechanical and optical measures must be taken when
carrying out servicing and maintenance work, to ensure that the outputs cannot be accident-
ally triggered. Once the servicing or maintenance activities have been finished, the security
precautions must once again be removed!
System operation in the event of an alarm
FIRE
Delay
Intervention
Buzzer silenced
Reset Alarm/
System
Actuated
Fault
Disable/Enable
Call Fire Brigade
Site Info
Access Code
Zone
Output
Input
Other Elements
Additional
Information
Menu
On
Off
Set Reset
Other
Commands
1 2 3
4 5 6
7 8 9
0
Alarms Faults Disablements Actuations Other Lists
Schrack Seconet
0000 0000 0000 0000 0000
29.01.2020
INTEGRAL
Operation
Faults
System
Power
Disablements
Test Mode
Fire protection
equipment
Call Service
Actuated
Fault
Silence/
Resound
Disable/Enable
1
2
3
4
5
6
7
8 9
10
11
12
13 14
15
16
17
18
Fire alarm
A fire alarm is indicated visually and acoustically:
The FIRE A indication flashes, the alarm signal
sounds and the detector zone, detector number and
the number of alarms that have been received are
displayed on the operating panel display.
Reset (mute) or disable sirens
Only use this function when the building has been
completely cleared.
Pressing the button Silence/ Resound Q resets
activated sirens (mutes them), but these are reactiv-
ated together with the arrival of the next alarm.
LED lights up, if the sirens were reset.
Pressing the button Disable/Enable R switches
off the main siren and all other sirens and alarm
areas. The LED next to the button and the O
LED lights up, if the alarm systems are disabled.
The sirens are not activated, even not in case of an
occurring alarm.
Exploration/intervention
function
(Depends on programming; delay function must be
activated)
Pressing the button Intervention C within the
acknowledgement time activates the exploration/in-
tervention function. The LED next to the button
lights up and the signal tone for the acknowledge-
ment period can be heard. The activation of the
main detector output is delayed by the programmed
intervention period.
CAUTION
Confirmed fire alarm
If a fire is actually discovered during intervention
period, the fire brigade has to be notified immedi-
ately. The manual call point can be used for im-
mediate alarm notification.
Reset alarm
(An authorisation code must be entered for this to
be permitted)
Only use this function if it is ensured that there is
no longer any danger or if you are instructed to do
so by the fire brigade. The cause of the alarm mes-
sage must be eliminated.
If it has been proven within the intervention period
that there is no fire, then the alarm can be reset by
pressing the Reset Alarm/System E button
without the fire brigade being notified.
If the transmission equipment is actuated (LED
Actuated F flashes), the alarm can no longer be
reset.
Transmission system actuated
If the LED Actuated F flashes, then the location
offering assistance has already been informed of the
alarm.
Do not press another button, wait for the support
and assistance staff to arrive. Have the necessary
plans ready.
EN
Subject to technical changes
© Schrack productions · B-HB-0108EN · V 2.0 · 01.2021
SCHRACK SECONET AG
Eibesbrunnergasse 18
A-1120 Vienna
Tel. +43 1 81157
www.schrack-seconet.com
