SCHROTH Interior Net Quick start guide

INSTALLATION and USE
GUIDELINE
SCHROTH INTERIOR &RACING NET
Edition: 01/2019
PartNo:EA14.2
Thank you for choosing our product.
The SCHROTH Racing “Double Take Ratchet-Release Racing Net”
uses a unique patented ratchet-release system for ease of
emergency exit, using the red “lanyard” to disengage the net. The
net is made from Polyester, it should be mounted tight when
installed, but does not have to be “guitar string” tight to work
correctly.
Please follow the simple installation instructions below:
1) Install and attach net, using the FIA 8863-2013 Racing Net
Installation Specification Guide [see www.fia.com]. All attach
points must be capable of handling a 2250lbf [10kN] applied
pull load. The front strap can be attached with bolt-in, clip-in
or wrap around option, using the 3-bar slide. Please call for
information on available manufacturer mounting solutions.
2) Adjust net using the 3-bar slide to get the net as tight as
possible. *(see 3-bar adjustment image)
3) Make sure you are satisfied with the location and attach points
of the net.
4) Tighten the ratchet latch until about 6 ft-lbf [8 Nm] is reached.
INSTALLATION PER FIA 8863-2013
INSTALLATION AND LOADS
Load Case for Attachment Points
The front-straps of each Racing Net shall have a single attachment to
the car. The attachment shall be designed to sustain 10kN MIN with
15mm MAX deformation.
Each rear-strap of the Racing Net shall attach to the car at a separate
position. The attachments shall be designed to sustain 10kN MIN with
15mm MAX deformation.
Fitment of handed Nets
Nets are typically handed; left or right. The net horizontal webbing
shall be located towards the driver, to provide the smoothest surface
for the helmet to glide on, with the net vertical webbing located away
from the driver.
WRAPPING OF NET
1 2



100mm [4“]
MIN

USE OF PUSH BUTTON BUCKLE
T
o release or in an
event of an emer
g
ency
requirin
g
exit or
extrication, push red
release button on front
of the automotive style
push button buckle.
USE OF DOUBLE TAKE RATCHET SYSTEM
USE OF DOUBLE TAKE RATCHET SYSTEM
FIXATIONS TO ROLLCAGE
Optional fixation to rollcage - not load bearing.
Latch/Tongue and Ratchet should be installed upwards at a 90° ±15°
orientation.
ADDRESSES AND COPYRIGHTS
SCHROTH Safety Products GmbH
Im Ohl 14
59757 ARNSBERG
GERMANY
Phone: [phone]
FAX: [phone]
eMail: [email protected]
www.schroth.com
Warranty issues or questions in North America can be directed to our
importer
HMS Motorsport, 119 Bevan Drive, Mooresville, NC 28115 or by
calling toll free 800-884-2358.
SCHROTH reserves the right to incorporate any technical changes or
further development in this product without notice. Our web site
www.schroth.com will inform you about actual instructions and
products. Also regional representatives and further importers are listed
by countries.
REGISTERED TRADEMARKS:
SCHROTH®and SCHROTH Racing® are international registered
trademarks of SCHROTH Safety Products GmbH, Im Ohl 14,
59757 Arnsberg, Germany.
COPYRIGHTS:
The copyrights of this “Installation and Use Guideline” are property of
SCHROTH Safety Products GmbH, Im Ohl 14, 59757 Arnsberg,
Germany.
Copyright of this in part or in whole, on paper, on film or electronically
is allowed only after written permission by SCHROTH Safety Products
GmbH, Im Ohl 14, 59757 Arnsberg, Germany.
© 2019, SCHROTH Safety Products GmbH, Germany
3 4
90° ±15°