Schwinn Cadence Pro Service manual

Core Health & Fitness
4400 NE 77th Avenue, Suite 300
Vancouver, WA 98662
Telephone:[phone]
SchwinnEquipment.com
Document Number 620-8203
For more information visit SchwinnEquipment.com
or call 1-888-678-2476
Group Cycle Computer
Installation Instructions
700-0008-KIT
Installation & Instructions
Schwinn Cadence ProTM Console

2
Manufacturer:
Core Health & Fitness
4400 NE 77th Ave, Ste 300
Vancouver, WA 98662
t:1-888-678-2476
www.SchwinnEducation.com
Product Description:
Group cycling computer for Schwinn®indoor bikes.
Table of Contents
Components in the Box......................................................................3
Tools Required for Assembly..............................................................4
Specications ....................................................................................4
Warranty and Customer Support .......................................................4
Certications.......................................................................................5
Computer Bracket Mount Compatibility .............................................6
Computer Mounting
IC Pro20 ......................................................................................7
IC Pro ........................................................................................10
ACPP.........................................................................................13
AC Sport....................................................................................15
Set Gear Ratio............................................................................18
Instructions for Group Cycle Computer
Using the Console......................................................................19
Pairing Flywheel Transmitter to Console....................................21
Pairing Chest Transmitter to Console.........................................22
Personal Data Settings...............................................................23
Maintenance ....................................................................................24
Frequently Asked Questions ............................................................25

3
Installation & Instructions
Frequently Asked Questions:
What are the Personal Data Settings for use at HOME and in a CLUB?
HOME setting should be followed using the procedures indicated starting
on page 23. Imputing you AGE, AHR and WT will give you the most accu-
rate estimate of caloric expenditure on the bike.
CLUB•
•
setting could either be done buy entering your own personal data as
indicated in the instructions on page 23 or by using the DEFAULT settings
within the bikes computer.
NOTE: Using the computers default setting may not accurately represent your
own caloric expenditure.
What is Ambient Heart Rate (AHR)?
Ambient Heart Rate (AHR) is your normal heart rate during the day when you
are going about your day-to-day activities, but not exercising. You can calculate
your AHR while you are sitting and reading a book, watching TV, working on the
computer, etc. Take your Ambient Heart Rate for 3 days to determine your
average AHR.
How does Ambient Heart Rate (AHR) differ from Resting Heart Rate
(RHR)?
Resting Heart Rate (RHR) is your heart rate when you are in a complete state
of rest. It is usually taken in the morning after awaking and before arising from
bed.Whereas Ambient Heart Rate (AHR) is your normal heart rate during the
day as you are going about your normal day-to-day activities. AHR for the gen-
eral population is generally in the 70’s.World class athletes AHRs are in the
40’s and 50’s.
What are the Group Cycle Computers Default Settings?
When the rider does not enter their own personal data for calculation of caloric
expenditure, the computer will use its preprogrammed Default settings.
The three Default setting are: Age (AGE): 30, Ambient Heart Rate (AHR): 70
bpm, Weight (WT) Kg/lb): 70 kg (154 lbs).
What if I Do Not want other riders to know my Personal Data Settings?
Inputting your personal data is the most accurate method for calculating an esti-
mate of caloric expenditure. This information will NOT be stored and the Group
Cycle Computer will revert back to the Default setting when it turns off, 5 min-
utes after the riding session or when left alone for 5 minutes.
In the Heart Rate display, what does the %MHR mean and what is that
number?
The Group Cycle Computer will automatically determine your predicted Maximal
Heart Rate (MHR) when you input your personal data during the setup. The %
of MHR display indicates exercise intensity using the formula 220-age to repre-
sent 100%, and then current heart rate as a percentage of the maximum.
Installation & Instructions
Components in the Box:
DESCRIPTION QUANTITY
1elosnoCretupmoCgnilcyCpuorG
1)3(stloBhtiwtekcarBtnuoMgniR
1)4(stloBhtiwtekcarBtnuoMtalF
1tekcarBgniRroflaeSenociliS
Silicone Seal for Flat Bracket 1
1rettimsnarTleehwylF
Flywheel Transmitter Foam Holder
(Foam holder for Internal Transmitter Mounting) 1
1tengaM
1mihSgnidloHevisehdAtengaM
3elosnoCretupmoCrofseirettaBAAA
25mm Mounting Bolts and Spacers
(used with older handlebar design) 4
Double Stick Adhesive for Transmitter Mounting 1
Tools Required for Assembly:
1. Phillips Head Screwdriver
2. 3mm Allen Key
Tools Required for Assembly:
1- Phillips Head Screwdriver
2- 3mm Allen Key
DESCRIPTION QTY
MAGNET MOUNT..............................................................................1
MAGNET............................................................................................1
SPEED SENSOR...............................................................................1
COMPUTER CONSOLE ....................................................................1
RUBBER SHIMS ...............................................................................4
MANUAL.............................................................................................1
SILICONE SEAL.................................................................................1
CONSOLE MOUNTING BOLTS.........................................................3
SINGLE RING MOUNT......................................................................1
DOUBLE RING MOUNT ....................................................................1

4
Installation & Instructions
Group Cycle Computer Console
Specifications
Features:
• ANT+ interoperable 2.4Ghz wireless technology
• Low power consumption for long battery life
• Code memory during battery displacement
• Triple data display; Cadence, Heart rate and Training data
• Automatic Scan function
• Advanced energy expenditure algorithm for personalized KCALS
(Calories)
• Bright LED screen light
• Dual mode ANT+ and heritage 5.4Khz analogue Fit1e heart rate
receiver
• FCC ID: QSWASPDCS
• CE Compliant
• ANT+ Certified
• RoHS Compliant
General:
• ANT+ 2.4 GHz wireless radio to transmit data
• Batteries Required:
- Console uses 3-AAA batteries
- Flywheel transmitter uses 1 CR2032 lithium coin cell battery
- Life of batteries depends on usage
Warranty:
One year warranty on computer and transmitter.
Warranty excludes batteries.
Customer Support:
If any items need replacement contact the Customer Support Department at
1-888-678-2476 STAR TRAC Group Cycle Computer Installation 21
Installation & Instructions
Maintenance
We strongly recommend performing the regular daily, weekly and monthly
preventive maintenance routines outlined below. If any items need re-
placement contact Customer Support Department at 1-888-678-2476.
D= Daily W= Weekly M= Monthly
D W M Procedure
Daily maintenance of the computer will determine its life of the
computer by how consistently it is performed.
 •Wipe down the computer with a soft cloth after each use.
 •Dilute Simple Green (1) with water (30) (30:1 ratio) spray
onto a soft cloth then wipe the computer console.
NOTE: Never spray directly onto the computer console.
 •Never use abrasive cleaning liquids or oil base, ammonia or
alcohol when wiping down the computer.
The weekly maintenance should focus on the overall
performance of the computer. During this portion of the
maintenance look for vibration and possible loose assemblies.
 •Inspect each computer for loose parts, bolts and nuts. Ad-
just as necessary.
 •Remove any computers that are not properly mounted or
deemed unsafe.
The monthly maintenance check should be a comprehensive
inspection of the overall assembly components of the computer.
 •inspect all areas for proper adjustments.

•Inspect all parts to determine damage which will require pos-
sible part replacement.

•Battery Low will display when the battery needs replacement.
Replace the batteries in the computer with 3 high quality AAA
Alkaline batteries such as Duracell or Energizer.

•Inspect the mounting of the cadence transmitter and magnet
to insure it is intact and working properly.
NOTE: Depending on the amount of use, some procedures may need to be
performed more frequently.
If any items need replacement, contact your distributor or the Customer
Support Department at 1-888-678-2476.
kHz
On Screen Features:
• RPM; Current & session average
• Heart rate; Current, session Average and % of Maximum heart rate
• Training data; Exercise session time and equivalent distance traveled
• Personalized session KCALS (Calories)
• Low Battery Indicator

5
Installation & Instructions
Personal Data Settings and Chest Transmitter Pairing
The product comes with three default settings:
 Age (AGE): 30
 Ambient heart rate* (AHR): 70 bpm
 Weight (WT) Kg/Ibs): 70kg (154 Ibs)
1. Press Set key to set age (AGE) adjust using the up key
or down key.
2. Press Set key to set ambient heart rate* (AHR) adjust using
the up key or down key
3. Press Set key to set weight (WT) in (Kg /Ib) adjust using
the up key or down key.
4. Press Set key to finish and return to main display.
* Ambient Heart Rate is your normal heart rate during the day when you are
going about your day-to-day activities, but not exercising.
Once complete the personal data is stored in the console memory, this can
be changed or modified during exercise or when paused by pressing and
holding Set key
The chest transmitter has to be paired to the console prior to starting the ex-
ercise to achieve accurate results, and must be paired again before the start
of every new exercise.
If the display turns off automatically after 5 minutes without any activity, then
the console has entered sleep mode. The personal settings data will return to
the default settings.
STAR TRAC Group Cycle Computer Installation 5
Installation & Instructions
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
Changes or modifications not expressly approved by Star Trac could void the
user’s authority to operate the equipment
FCC ID: QSWASPDCS
Certifications
EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC.
ANT+TM Performance Console is ANT+ certified.
Installation & Instructions
Personal Data Settings and Chest Transmitter Pairing
The product comes with three default settings:
 Age (AGE): 30
 Ambient heart rate* (AHR): 70 bpm
 Weight (WT) Kg/Ibs): 70kg (154 Ibs)
1. Press Set key to set age (AGE) adjust using the up key
or down key.
2. Press Set key to set ambient heart rate* (AHR) adjust using
the up key or down key
3. Press Set key to set weight (WT) in (Kg /Ib) adjust using
the up key or down key.
4. Press Set key to finish and return to main display.
* Ambient Heart Rate is your normal heart rate during the day when you are
going about your day-to-day activities, but not exercising.
Once complete the personal data is stored in the console memory, this can
be changed or modified during exercise or when paused by pressing and
holding Set key
The chest transmitter has to be paired to the console prior to starting the ex-
ercise to achieve accurate results, and must be paired again before the start
of every new exercise.
If the display turns off automatically after 5 minutes without any activity, then
the console has entered sleep mode. The personal settings data will return to
the default settings.
STAR TRAC Group Cycle Computer Installation 5
Installation & Instructions
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
Changes or modifications not expressly approved by Star Trac could void the
user’s authority to operate the equipment
FCC ID: QSWASPDCS
Group Cycle Computer Console
Certifications
EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive
1999/5/EC.
ANT+TM Performance Console is ANT+ certified.
NOTE: The users’ device must be ANT+ compatible and capable of receiving the data
les broadcast by the ANT+ chip. Users should consult with the documentation for their
device, or check the ANT+ website at www.thisisant.com for compatibility
Cadence Pro Computer

6
Fig. 1
Schwinn®IC ProTM
Schwinn®AC SportTM
Schwinn®AC Performance PlusTM
Schwinn®IC PRO20TM
Fig. 2
Cadence Pro Computer
Bracket Mount Compatibility:
The following products can have the
Cadence Computer installed using
the clamp bracket setup shown in
(Fig.1).
The following products can have
the Cadence Pro Computer in-
stalled using the clamp bracket
setup shown in (Fig 2).

7
IC PRO20
1.Take the Cadence Pro Computer and silicone seal (Fig. 1). Line up the silicone seal
to the proper holes and apply it to the Cadence Pro Computer. (Fig. 2).
Fig. 1
2. Place the 2-loop mount on the back of the computer and tighten the 3 screws to the
computer (Fig. 3).
Tools Required
• 3mm Hex Key
• Philips Screw Driver
• Cadence Pro Computer Kit PN 740-8803

8
5. Unscrew chain guard screws to use for sensor mount (Fig 7).
Fig. 5
Fig. 7
Fig. 6
Note: On the IC Pro 20, computer can be
mounted on the fore or after cross bar
3. Unscrew screws that hold the loops together (Fig 4).
4. Wrap the loops around the handlebar. (Fig. 5 & Fig. 6). NOTE: If loops do not fit
snugly around the handlebars, use the rubber shims to take up the slack.

9
6. Install the sensor, screw on the top and bottom screw (Fig. 8).
7. Peel off the adhesive patch (Fig. 9).
Fig. 8
Fig.10
Fig. 9
Fig. 11
8. Place plastic piece so that the curve at the bottom sits against the axle hub (Fig. 10).
9. Turn ywheel to verify the light on the sensor lights up (Fig. 11).
10. Set gear ratio, see pg 18.

10
IC PRO
Tools Required
• 3mm Hex Key
• Philips Screw Driver
• Cadence Pro Computer Kit PN 740-8803
1.Take the Cadence Pro Computer and silicone seal (Fig. 1). Line up the silicone seal
to the proper holes and apply it to the Cadence Pro Computer. (Fig. 2).
2. Tighten the 3 screws to the computer (Fig. 3).

11
5. Unscrew top and bottom chain guard screws to use for sensor mount (Fig 7).
Fig. 5 Fig. 6
Fig. 7
3. Unscrew screws that hold the loops together (Fig. 4)
4. Insert clip on to the handlebar computer facing upwards (Fig. 5 & Fig. 6). NOTE: If
loops do not fit snugly around bars, use the rubber shims to take up the slack.

12
6. Take the sensor, screw on the top and bottom screw (Fig. 8).
7. Peel off the adhesive patch that holds the magnet to the ywheel (Fig. 9). Place plastic
piece so that the curve at the bottom sits against the axle hub (Fig. 10).
Fig. 8
Fig. 9
Fig. 11
Fig. 10
8. Turn ywheel to verify the light on the sensor lights up (Fig. 11).
9. Set gear ratio, see pg 18.

13
AC PERFORMANCE PLUS
Tools Required
• 3mm Hex Key
• Philips Screw Driver
• Cadence Pro Computer Kit PN 740-8803
1.Take the Cadence Pro Computer and silicone seal (Fig. 1). Line up the silicone seal
to the proper holes and apply it to the Cadence Pro Computer. (Fig. 2).
Fig. 1 Fig. 2
2. Place the one-ring mount on the back of the computer. Insert and tighten the
three mount screws (Fig. 3). Remove the screw that holds the loop together (Fig. 4)
Chain or Carbon Blue

14
Fig. 7
4. Install the sensor, screw on the bottom left screw (Fig. 7).
NOTE: The AC Performance Plus does not need any magnet installed because it’s
pre-installed on the ywheel.
5. Set gear ratio, see pg 18.
3. Wrap the loop around the handlebar computer facing upwards (Fig. 5 & Fig. 6).
Fig. 5 Fig. 6

15
AC SPORT
Tools Required
• 3mm Hex Key
• Philips Screw Driver
• Cadence Pro Computer Kit PN 740-8803
Fig. 1 Fig. 2
Fig. 3
2. Tighten the 3 screws to the computer (Fig. 3).
1.Take the Cadence Pro Computer and silicone seal (Fig. 1). Line up the silicone seal
to the proper holes and apply it to the Cadence Pro Computer. (Fig. 2).
Chain or Carbon Blue

16
3. Unscrew screws that hold the loops together (Fig. 4).
4.Wrap the loops around the handlebar computer facing upwards (Fig. 5 & Fig. 6).
5. Install the sensor, screw on the bottom left screw (Fig. 7).
Fig. 7

17
8. Turn ywheel to verify the light on the sensor lights up.
9. Set gear ratio, see pg 18.
6. Peel off the adhesive patch from the RPM sensor magnet mount (Fig. 8).
7. Place plastic piece so that the curve at the bottom sits against the axle hub (Fig. 9).

18
S M
LM
S S
S S S S
S
E1 E2a E3a E3a-1 *1 E4a
E3b-1 E4b
E3a-2 *2 E3a-3 E3a-4 E3a-5
Remark *1: Press MODE Button for automatically pairing
*2: Press Long MODE Button for manual pairing
*3: Press Button defines as below:
S: SET Button; LS: Long press SET Button
M: MODE Button; LM: Long press MODE Button
S
E5a
(1:3.25)
(1:4.65)
Schwinn Console (ZM6-S) Function Flow Chart (Engineering Mode) Date: 2015/2/25
Press any key before battery enter
SET Button
MODE Button
Start/Pause/Up
Light/ Down Button
Flow Chart A
Up/down key to select different gear ratio
ENTER AND NAVIGATE MAINTENANCE MODE
NOTE: For the IC Pro and IC Pro 20, select gear ratio 1:3.2.
For the AC Sport and ACPP Chain bike, select gear ratio 1:4.5.
For the AC Sport and the ACPP Carbon Blue, select gear ratio 1:A.65.

19
Installation & Instructions
Using The Console
1. The top display (RPM) shows cadence in RPMs, average
RPM (AVG RPM) and low battery indicator. Cadence in RPM is the
speed of the pedal crank. The average rpm (AVG RPM) indicates the
average speed in RPMs since the start of the exercise.
2. The Middle display (HEART RATE) shows heart rate, session average
and % of maximum heart rate (MHR). The heart rate is presented in beats
per minute. Average (AVG) indicates the average heart rate since the
start of the exercise. The % of MHR display indicates exercise intensity
using the heart rate maximum formula 220-age to determine maximal
heart rate, and then current heart rate as a percentage of the maximum.
3. The bottom display (TRAINING) shows time, exercise session time, and
distance (the equivalent distance that would have been covered when
cycling on the road). To change which data is being shown press the
Mode key
STAR TRAC Group Cycle Computer Installation 9
Installation & Instructions
Flywheel Transmitter Installation:
The Flywheel Transmitter can be mounted in two different locations.
Steps 10 - 13 show an external shroud mounted transmitter.
Steps 14 - 18 show an internal shroud mounted transmitter.
7. With all bike models – Verify that the right side crank arm is
clear of any obstructions and that a clear path is available to the
inner side of the right crank arm as shown from the user left side.
8. Locate the magnet holding shim along with the magnet and mount
them directly on the inner surface of the user right side crank arm.
NOTE: It is recommended to wipe the contact surfaces with a mild
cleaner such as a diluted solution of Simple Green to remove any built-up
grime or grease residue.
9. Once the magnet is mounted; rotate cranks to ensure that the
magnet will not rub on the outer chain guard shroud.
Instructions for Cadence Pro Computer

20
4. Install the supplied rubber gasket
inlay behind the console (Fig. 7).
NOTE: If using the Round Tube
mounting bracket, the included
thin rubber gasket should also
be positioned inside the clamp.
Fig. 7
5. Depending on the model of bike
that the Group Cycle Computer is
being installed on, select the
correct bracket and secure it to the
console using the supplied Phillips
head screws (Fig. 8).
NOTE: The 3 shorter Phillips head
screws are used to clamp the
bracket to the back of the console
while the longer Phillips head
screw is used to clamp the round
bracket to the round handlebar
tube.
Fig. 8
6. Using the correct hardware; mount
the Group Cycle Computer and
bracket assembly in the desired
location on the handle bars
STAR TRAC Group Cycle Computer Installation 17
Installation & Instructions
4. To START and PAUSE the timer press the start/pause/up key
To reset the timer press and hold the Mode key This
can be done when displaying any TRAINING session.
5. SCAN feature:
To use the SCAN feature press the Mode key 3 times until
(SCAN) appears in the TRAINING display. This will automatically change
between TRAINING data in intervals of 3 seconds showing: DISTANCE,
TIME and KCAL.
To stop the SCAN feature press the Mode key The SCAN
symbol should have disappeared.