Schwinn SC7 User manual

Assembly Instructions
Page 1
620-8607 Rev. A
SC5 + SC7 + SC Power Install Sheet
Applies to: SC5 (9-7410) + SC7 (9-7400) + SC Power (9-7380)
SC5 ASSEMBLY INSTRUCTIONS
STEP 1: Install the front stabilizer using two (2) pieces each of the
M10 x 25mm hex head screws, M10 split lock washers, and M10
washers. Repeat this step to attach the rear stabilizer.
STEP 2: Install the seat post by loosening the height adjustment
pop pin, then pulling outwards on the pin while sliding the seat
post into the frame.
STEP 3: Pull down on the seat slider locking pin then slide the
seat assembly onto the seat post installed in Step 2, tightening
the fore/aft adjustment knob to lock the seat slider into place.
NOTE: The fore/aft adjustment knob may need to be loosened.
STEP 4: Insert one (1) piece of the trapezoidal locking nut into
the handlebar post then slide the handlebar onto the handlebar
post. Next, insert one (1) piece of the threaded collar locking nut
through the handlebar and into the trapezoidal locking nut, tight-
ening with a 10mm allen key. Slide one (1) M8 washer onto the
fore/aft adjustment knob then tighten the knob into the threaded
collar locking nut. Finally, secure the end cap onto the handlebar
post using one (1) piece of the M4 x 10mm screw.
Fore/Aft
Adjustment
Knob
M8 Washer
Threaded Collar
Locking Nut
Trapezoidal
Locking Nut

Assembly Instructions
Page 2
620-8607 Rev. A
SC5 ASSEMBLY INSTRUCTIONS CONT.
STEP 5: Install the user right side pedal into the crank arm then
use a torque wrench and a 8mm allen socket to secure one (1)
piece of the crank bolt from the other side of the pedal, torquing
to 33-37 ft-lbs (45-50 Nm). Repeat this step for the rider left side
pedal.
NOTE: The pedal MUST be torqued to the above specications
otherwise a failure of the pedal may occur.

Assembly Instructions
Page 3
620-8607 Rev. A
SC7 ASSEMBLY INSTRUCTIONS
STEP 1: Slide the threaded stabilizer plate into the bike frame
then use a 13mm socket to secure the rear stabilizer onto the
frame using two (2) pieces of the M8 x 30mm bolts and M8 wash-
ers. Repeat this step for the front stabilizer.
STEP 2: Insert one (1) piece of the trapezoidal fore/aft locking
nut into the handlebar post then slide the handlebars onto
the handlebar post. Secure one (1) piece of the threaded collar
locking nut through the handlebars and into the trapezoidal fore/
aft locking nut using a 10mm allen key. Next, slide one (1) piece
of the M8 washer onto the fore/aft adjustment knob then tighten
the fore/aft adjustment knob into the threaded collar locking nut.
STEP 3: Slide the seat post into the frame by loosening the height
adjustment pop pin, then pulling outwards on the pin while
sliding the seat into the frame.
STEP 4: Pull down on the seat slider locking pin then slide the
seat assembly onto the seat post installed in Step 3, tightening
the fore/aft adjustment knob to lock the seat slider into place.
Fore/Aft
Adjustment
Knob
M8 Washer
Threaded Collar
Locking Nut
Trapezoidal
Locking Nut
Threaded
Stabilizer
Plate

Assembly Instructions
Page 4
620-8607 Rev. A
SC7 ASSEMBLY INSTRUCTIONS CONT.
STEP 6: Install the pedal into the crank arm then use a torque
wrench and a 8mm allen socket to secure one (1) piece of the
crank bolt from the other side of the pedal, torquing to 33-37 ft-
lbs (45-50 Nm). Repeat this step for the rider left side pedal.
NOTE: The pedal MUST be torqued to the above specications
otherwise a failure of the pedal may occur.

Assembly Instructions
Page 5
620-8607 Rev. A
SC POWER ASSEMBLY INSTRUCTIONS
STEP 1: Slide the threaded stabilizer plate into the bike frame
then use a 13mm socket to secure the rear stabilizer onto the
frame using two (2) pieces of the M8 x 30mm bolts and M8 wash-
ers. Repeat this step for the front stabilizer.
STEP 2: Insert one (1) piece of the trapezoidal fore/aft locking
nut into the handlebar post then slide the handlebars onto
the handlebar post. Secure one (1) piece of the threaded collar
locking nut through the handlebars and into the trapezoidal fore/
aft locking nut using a 10mm allen key. Next, slide one (1) piece
of the M8 washer onto the fore/aft adjustment knob then tighten
the fore/aft adjustment knob into the threaded collar locking nut.
STEP 3: Slide the seat post into the frame by loosening the height
adjustment pop pin, then pulling outwards on the pin while
sliding the seat into the frame.
STEP 4: Pull down on the seat slider locking pin then slide the
seat assembly onto the seat post installed in Step 3, tightening
the fore/aft adjustment knob to lock the seat slider into place.
Fore/Aft
Adjustment
Knob
M8 Washer
Threaded Collar
Locking Nut
Trapezoidal
Locking Nut
Threaded
Stabilizer
Plate

Assembly Instructions
Page 6
620-8607 Rev. A
SC POWER ASSEMBLY INSTRUCTIONS CONT.
STEP 6: Install the pedal into the crank arm then use a torque
wrench and a 8mm allen socket to secure one (1) piece of the
crank bolt from the other side of the pedal, torquing to 33-37 ft-
lbs (45-50 Nm). Repeat this step for the rider left side pedal.
NOTE: The pedal MUST be torqued to the above specications
otherwise a failure of the pedal may occur.