Scotsman MDT5N40A-1B User manual

INTRODUCTION
To the owner or user: The service manual you are
reading is intended to provide you, and the
maintenance or service technician with the
information needed to install, start up, clean,
maintain, and service this ice maker-dispenser.
The machine is a combination nugget ice maker
and countertop dispenser, with the option of wall
mounting.
The ice making section is equipped with the
following features: electronic controls for bin level
and low water; thermostatic expansion valve; front
service for most components; and R-404A
refrigerant. The ice dispensing section is a
seamless plastic storage bin, with a stainless steel
rotating vane to sweep the ice into the dispensing
chute.
MDT5N25 & MDT5N40
May 2001
Page 1
Table of Contents
FOR THE INSTALLER: Specifications···································· Page 2
FOR THE INSTALLER: Environmental Limitations ····························· Page 3
FOR THE INSTALLER············································ Page 4
FOR THE INSTALLER: Wall Mount Kit ··································· Page 5
FOR THE PLUMBER ············································ Page 6
FOR THE ELECTRICIAN ·········································· Page 7
FOR THE INSTALLER: Final Check List ·································· Page 8
INITIAL START UP ············································· Page 9
COMPONENT DESCRIPTION ······································· Page 10
COMPONENT DESCRIPTION ······································· Page 11
COMPONENT DESCRIPTION: Control Box ································ Page 12
ELECTRICAL SEQUENCE ········································· Page 13
OPERATION: Water ············································· Page 14
OPERATION: Refrigeration ········································· Page 15
OPERATION: Ice Vending ·········································· Page 16
DISPENSE AREA SANITATION······································· Page 17
CLEANING and SANITIZING ········································ Page 18
MAINTENANCE AND CLEANING······································ Page 19
SERVICE DIAGNOSIS ··········································· Page 21
SERVICE DIAGNOSIS: Circuit Board ···································· Page 23
REMOVAL AND REPLACEMENT······································ Page 24
REMOVAL AND REPLACEMENT: Bearing And Breaker ·························· Page 25
REMOVAL AND REPLACEMENT: Water Seal ······························· Page 27
TO REMOVE AND REPAIR THE GEARMOTOR ASSEMBLY ······················· Page 29
REFRIGERATION SERVICE: R-404A (HP62) ······························· Page 30
REFRIGERATION SERVICE ········································ Page 31
CIRCUIT BOARD SERVICE········································· Page 32
LIQUID CHARGING ············································ Page 32
Note this symbol when it appears.
It marks a possible hazard.
Parts Lists and Wiring Diagrams are printed on
yellow paper in the center of this manual.
This manual was printed on recycled paper.
Keep it for future reference.

FOR THE INSTALLER: Specifications
MDT5N25 & MDT5N40
August 2010
Page 2
14.06" 1.88"dia
20.5"
22.5"
2.56"
Optional for water and
drain lines
Serial Number Plate
inside on upper base
below control box.
ELECTRICAL JUNCTION BOX
3/8" FPT
condenser
Water Inlet
(Water Cooled)
1/2" FPT
Cond. Drain
(Water Cooled)
12.27"
1.12"
3.12"
5.12"
6.43"
4.5"
3.54"
3/8" Flare
Potable Water Inlet
NAMEPLATE
on back panel
SPECIFICATIONS
Model Number Dimensions (w/o stand)
H”xW”xD”
Basic
Electric
Cond.
Type
Ref. Charge,
R-404A in ounces*
Minimum Circuit
Ampacity
Maximum
Fuse Size
MDT5N40A-1J 48.5 x 26 x 22.5 115/60/1 Air 24 19.3 25
MDT5N40W-1J 48.5 x 26 x 22.5 115/60/1 Water 17 17.8 20
MDT5N25A-1J 41 x 26 x 22.5 115/60/1 Air 24 19.3 25
MDT5N25W-1J 41 x 26 x 22.5 115/60/1 Water 17 17.8 20
MDT5N40A-1B 48.5 x 26 x 22.5 115/60/1 Air 24 19.3 25
MDT5N40W-1A same 115/60/1 Water 18 17.8 20
MDT5N40W-1B same 115/60/1 Water 17 17.8 20
MDT5N40A-6B same 230/50/1 Air 24 11 15
MDT5N40W-6A same 230/50/1 Water 18 10.4 15
MDT5N40W-6B same 230/50/1 Water 17 10.4 15
MDT5N25A-1B 41 x 26 x 22.5 115/60/1 Air 24 19.3 25
MDT5N25W-1A same 115/60/1 Water 18 17.8 20
MDT5N25W-1B same 115/60/1 Water 17 17.8 20
MDT5N25A-6B same 230/50/1 Air 24 11 15
MDT5N25W-6A same 230/50/1 Water 18 11 15
MDT5N25W-6B same 230/50/1 Water 17 11 15
* Refrigerant charge change between A and B water cooled. Always check the nameplate for charge info.
3/4" FPT
Drain

FOR THE INSTALLER: Environmental Limitations
Installation Limitations
This ice system is designed to be installed indoors,
in a controlled environment.
Minimum Maximum
Air Temp 500F. 1000F.
Water Temp 400F. 1000F.
Water Pressure 20 PSI 80 PSI
Voltage (115v) 104 126
Operating the machine outside of the above
limitations, or outdoors, is potentially damaging to
the machine; also it is misuse of the machine,
which may void the warranty.
Scotsman Ice Systems are designed and
manufactured with the highest regard for safety
and performance. They meet or exceed the
standards of UL and NSF.
Scotsman assumes no liability or responsibility of
any kind for products manufactured by Scotsman
that have been altered in any way, including the
use of any part and/or other components not
specifically approved by Scotsman.
Scotsman reserves the right to make design
changes and/or improvements at any time.
Specifications and design are subject to change
without notice.
Water Limitations
An ice machine is a food manufacturing plant; it
takes a raw material, water, and turns it into a food
product, ice. The purity of the water is very
important in obtaining pure ice and in maximizing
product life. This section is not intended as a
complete resource for water questions, but it does
offer these general recommendations:
1. Filter the water used to produce ice. That is the
water going to the “potable” water connection.
Water filters vary greatly in ability and function.
Install one that filters out suspended solids to a
dimension of 5 microns or smaller. The finer the
filter the better, but finer filters will clog sooner than
course ones. It may be necessary to add a course
filter ahead of the fine filter to prolong filter life.
2. Check with a water treatment specialist for a
water test, and recommendations regarding filters
and treatment.
Service Limitations
Do not install in a location where the top of the
machine is within 6" of a fixed ceiling. Do not install
air cooled models in a location where there is less
than 6" clearance to the left and right of the
cabinet.
MDT5N25 & MDT5N40
May 2001
Page 3
WALL
CUT AWAY
CEILING
CUT AWAY
6" SPACE
FOR AIR
(AIR COOLED)
SPACE
ABOVE
FOR
SERVICE
6" SPACE
FOR AIR
(A/C)
SPACE
FOR
UTILITIES
Airflow

FOR THE INSTALLER
Location
After uncrating and inspection, the unit is ready for
installation. It is important that the machine be
installed in a location where it has enough space
above and behind it for service. Air cooled models
require a minimum of 6 inches to the left and right
of the machine for air circulation.
Machine Stand Installation
Tip the stand on its back and install the legs, return
the stand to the upright position. Adjust leg levelers
so that the stand does not “rock”.
Counter Top or Machine Stand Installation
The base of the icemaker-dispenser must be
sealed to the object it rests upon. Food grade
silastic sealant such as Scotsman part number
19-0529-01 is recommended.
Place a bead of the sealant on the machine stand
or counter top to match the outside edge of the
cabinet base and sink.
The icemaker-dispenser is heavy: use of a
mechanical hoist is recommended to lift it to the
height required to install it.
The DMS machine stand has holes in the top that
match up with threaded holes in the
icemaker-dispenser. Place the cabinet onto the
machine stand, so that the unit is lined up with the
holes. Secure the ice maker-dispenser to the
machine stand with bolts and washers.
In both counter top and machine stand
installations, wipe off and neatly smooth any
excess sealant. Level the machine stand and
cabinet.
Unpack and install the sink brackets. Fit the sink
assembly onto the two sink brackets, and press
onto the bead of sealant. Wipe off and neatly
smooth any excess sealant from under the sink
edge.
Unpack and install the ice and water spouts.
Ice Spout: Slide up and over ice outlet. No
fastener is required to hold it in place.
Water Spout: Slide over stainless steel water
discharge tube, locate and match up with notches
in the base. Rotate clockwise to move spout into
installed position.
MDT5N25 & MDT5N40
May 2001
Page 4
SEAL THE
UNIT TO
THE
COUNTER
OR STAND
Water
Spout
Ice Spout

FOR THE INSTALLER: Wall Mount Kit
CAUTION
It is recommended that the wall mounting
installation be done by an experienced contractor.
The weight of the machine when in use may
exceed 350 pounds. The unit should be mounted
on a solid, rigid wall with proper fasteners for that
type of wall and of adequate strength to support
the weight of the machine when in use.
Clearance between the wall and the icemaker is a
maximum of 1 inch. Check utility connections first.
The electrical junction box will have to be removed,
and the electrical connections made inside the
cabinet in compliance with local codes. The
plumbing connections may be made through the
base, or at either side through the pre-punched
holes, using standard plumbing practices.
Interior plumbing lines must be disconnected from
the original connections and plugged when
routing through the side or base.
1. Remove machine top. Attach bracket “A” to
machine using (3) nuts, (3) flat washers, (3) lock
washers, and (3) 5/16-18 bolts received with the
kit.
2. Mount brackets “B” and “C” to the wall at the
dimensions shown for the unit. (hardware for this is
not included).
Use fasteners and wall of sufficient strength to
carry the use and weight of the
icemaker-dispenser.
3. Lift unit up and hook bracket “A” over bracket
“B”. Slide unit until the two remaining holes are
aligned and secure with the remaining (2) 1/4-20
bolts, flat washers and lock washers.
MDT5N25 & MDT5N40
May 2001
Page 5
7.83
SIDE
ROUTIN
BASE
HOLE
DO NOT LIFT ON SINK
1" CLEARANCE
B
A
C
16"
16"
12"
12"
MDT6N40=38.6"
MTD6N25=30"

FOR THE PLUMBER
CONFORM TO ALL APPLICABLE CODES
Water Inlet
Air Cooled Models: The recommended water
supply is clean, cold water. Use 3/8" O.D. copper
tubing, connect to the 3/8" male flare at the back of
the cabinet. Install a hand valve near the machine
to control the water supply.
Water Treatment: In most areas, a water filter of
some type will be useful. In areas where the water
is highly concentrated with minerals the water
should be tested by a water treatment specialist,
and the recommendations of the specialist
regarding filtration and/or treatment should be
followed.
Water Cooled Models: A separate 3/8" O.D.
copper line is recommended, with a separate hand
valve to control it. It is connected to a 3/8" FPT
condenser inlet at the back of the cabinet. The
water pressure to all lines must always be above
20 psig, and below 80 psig.
Drains
Air Cooled Models: There is one 3/4" FPT drain
at the back of the cabinet, the drain line is of the
gravity type, and 1/4 inch per foot fall is an
acceptable pitch for the drain tubing. There should
be a vent at the highest point of the drain line, and
the ideal drain receptacle would be a trapped and
vented floor drain. Use only 3/4" rigid tubing.
Water Cooled Models: In addition to the above
mentioned drain, a separate condenser drain must
be installed. Connect it to the 1/2" condenser drain
connection at the back of the cabinet.
MDT5N25 & MDT5N40
May 2001
Page 6
WATER INLET
CABINET
DRAIN
OPTIONAL
WATER
FILTER
WATER INLET
SHUT OFF
VALVE
VENTED
DRAIN TUBE
FLOOR DRAIN
WATER COOLED DETAIL
Condenser
WATER INLET
POTABLE
WATER INLET Condenser
DRAIN
CABINET
DRAIN

FOR THE ELECTRICIAN
CONFORM TO ALL APPLICABLE CODES
The electrical power to the unit is
supplied through the junction box at the
rear of the machine.
Check the nameplate (located on the
back panel) for the voltage
requirements, and for the minimum
circuit ampacity. The machine requires
a solid chassis to earth ground wire.
The ice maker should be connected to
its own electrical circuit so it would be
individually fused. Voltage variation
must remain within design limitations,
even under starting conditions.
All external wiring must conform to
national, state, and local electrical
codes. The use of a licensed
electrician is required to perform the
electrical installation.
MDT5N25 & MDT5N40
July 2003
Page 7
JUNCTION
BOX
INDIVIDUAL CIRCUIT
FOR ICE DISPENSER

FOR THE INSTALLER: Final Check List
1. Is the icemaker-dispenser installed indoors, in a
location where the air and water temperatures are
controlled, and where they do not go beyond
design limitations?
2. Is there an electrical disconnect (switch or plug
as required) within sight of the installed machine?
Is the machine on a separate circuit? Has the
voltage been checked and compared to nameplate
requirements?
3. Have all of the plumbing connections been
made and checked for leaks?
4. Has the machine been leveled?
5. Is there a minimum of 6 inches of clearance at
the left and right sides of an air cooled machine?
6. Is there a minimum of 6 inches of clearance at
the top and back of the machine for service and
utility connections?
Wall mounted only: Is the machine properly
installed and secured to the wall?
7. Is there a water shut off valve installed near the
machine?
MDT5N25 & MDT5N40
July 2003
Page 8
BACK VIEW OF COMPLETED INSTALLATION
ICEMAKER
DISPENSER
MACHINE
STAND
ELECTRICAL?
LEVELED?
PLUMBING?

INITIAL START UP
Pre Start Inspection
1. Remove the two front panels.
2. Check that all shipping blocks have been
removed.
3. Remove any and all packing tape (check inside
the storage bin).
4. Inspect the interior of the machine for loose
screws or wires. Check that no refrigerant lines are
rubbing each other. Check that the fan blade on air
cooled models turns freely.
5. Check that the machine is installed correctly
according to the final check list.
Start Up
1. Go through the pre start inspection.
2. Open the water hand valve, observe that water
enters the water reservoir, fills the tube from the
reservoir to the evaporator and then shuts off.
Check for leaks.
3. Switch the master switch on. The electrical start
up sequence is automatic; there will be a short (15
second) delay before the machine starts.
4. On air cooled models, warm air will begin to flow
from the condenser. Water cooled models will
begin to discharge warm water down the drain.
5. The unit should soon be making ice. If desired,
the low side pressure may be checked: it should be
38 PSIG + or - 2 PSIG.
The air cooled discharge pressure will depend
upon air and water temperatures, but should be
between 240 PSIG and 340 PSIG.
Water cooled discharge pressure should be about
245 PSIG. If needed, adjust the water regulating
valve.
The above numbers are for new, clean machines.
Field values may be somewhat higher or lower.
6. There are no adjustments to make, so replace
the panels.
7. Check ice dispensing by holding a container in
front of the Touch Free ice sensor (just below the
ice delivery spout). Ice should flow from the spout
when a container is present, and stop dispensing
when the container is removed.
8. Switch off the icemaker-dispenser, remove the
top panel and the top of the ice storage bin.
Sanitize the interior of the ice storage bin by wiping
it with a mixture of 1 ounce of household bleach to
2 gallons of water, allow to air dry. Replace all
covers and panels. Switch the icemaker-dispenser
back on.
9. Give the owner/user the service manual, instruct
him/her in the operation and maintenance
requirements of the unit. Make sure they know who
to call for service.
10. Fill out the Customer Evaluation and Warranty
Registration form, and mail it in to Scotsman.
MDT5N25 & MDT5N40
May 2001
Page 9

COMPONENT DESCRIPTION
High Pressure Cut Out Switch: A manual reset
switch sensing the high side refrigeration pressure.
It is set to shut the machine off if the discharge
pressure should ever exceed 450 psig.
Evaporator: A vertical stainless steel tube,
refrigerated, and water filled. In it there is a
stainless steel auger.
Reservoir: Float operated, it maintains the water
level in the evaporator at a constant level, it also
contains the water level sensor.
Water Level Sensor: Senses if there is water in
the reservoir to make ice out of. Will shut the
machine off it there is none.
Ice Level Sensor: An electronic “eye”, it senses
the presence of ice in the
bottom of the ice discharge
chute. Operates to turn the ice
machine on and off
automatically as the level of ice
in the bin changes.
Drain Tube: When uncapped
and lowered, drains the
evaporator.
Condenser: Air or water
cooled, where the heat
removed in ice making is
discharged.
Ice Storage Bin Assembly: A
plastic lined, insulated cylinder
that receives, stores and
dispenses the ice. Fresh ice
enters at the top, and when the
bin is full enough the ice will be
between the ice level sensors,
and the ice making will stop. Ice
is dispensed through a chute at
the bottom front when the bin
vane sweeps the ice over the
chute.
MDT5N25 & MDT5N40
May 2001
Page 10
ICE LEVEL SENSORS
WATER LEVEL
SENSOR
RESERVOIR
EVAPORATOR
ICE STORAGE BIN
TOUCH FREE SENSOR
CONDENSER
DRAIN TUBE
HIGH PRESSURE
CUT OUT

COMPONENT DESCRIPTION
Evaporator: A refrigerated vertical tube filled with
water and containing a water seal and auger.
Auger: A solid stainless steel double spiral auger,
it pushes the ice crystals up to the top of the
evaporator.
Water Seal: A two part “face” seal, the top half
rotating with the auger, the bottom half stationary,
the sealing action being where the two seal “faces”
meet.
Ice Sweep: A plastic cap with “fingers”. It revolves
with the auger to “sweep” the ice into the ice chute.
Breaker: Where the ice is compressed and much
of the extra water is squeezed out of it before it is
discharged into the bin.
Motor: A split phase motor that drives the gear
reducer.
Thrust Bearing: As the ice is pushed up the
evaporator, the auger is thrust down, and pressure
from the auger thrust is taken up by this bearing.
MDT5N25 & MDT5N40
May 2001
Page 11
EVAPORATOR
AUGER
WATER SEAL
ICE SWEEP
BEARING
BREAKER
MOTOR

COMPONENT DESCRIPTION: Control Box
Circuit Board:
The circuit board receives
input signals from several
sensors and translates them to
control the electrical power
supply to the various loads.
The sensors include:
·Touch Free ice or water.
·Ice level in the bin.
·Water level in the reservoir.
The loads include:
·Compressor contactor
·Fan motor
·Bin drive motor
·Auger drive motor
·Water solenoid.
In addition, a “Clean” switch is
available to temporarily disable
the Touch-Free sensors for
cleaning of the splash panel.
On/Off Switch: Manual
control for the machine.
Contactor: A definite purpose
contactor connecting the
compressor to the power
supply.
Potential Relay: The
compressor start relay.
MDT5N25 & MDT5N40
May 2001
Page 12
CONTACTOR
CIRCUIT
BOARD
START
CAPACITOR
POTENTIAL
RELAY
ON-OFF
SWITCH

ELECTRICAL SEQUENCE
Refer the wiring diagram as needed.
The “Power” light on the board glows whenever
there is power to the machine (and the master
switch is ON).
If the machine is switched off at the master switch,
but is otherwise ready to go, switching the master
switch to ON does the following:
·The bin empty and power lights on the circuit
board glow.
·There is a 15 second delay
·If there is enough water in the reservoir, the
circuit board will allow the machine to start up.
Start up consists of:
·The compressor contactor coil receives power
from the circuit board.
·The contactor is energized, connecting power to
the compressor, and the compressor starts.
·The auger motor receives power from the circuit
board and starts.
·As ice goes past the ice level sensors, the bin
empty light will stay on and the machine will
continue to run, unless the ice stays between
the sensors for more than 15 seconds (bin full).
At that point, the bin empty light goes out, and
the machine shuts down.
Other reasons for shut down:
·Low water level (as sensed by the thermistor in
the reservoir).
Shut Down consists of:
·The compressor contactor opens
·The compressor stops
·The auger motor is run by the circuit board for 2
more minutes, clearing out ice in the evaporator,
and then
·The auger motor no longer receives power from
the circuit board, and the auger motor stops.
After a 6 minute delay, If the ice level sensor is
clear (bin empty) for more than 15 seconds, the
machine will start up again.
Another purpose of the circuit board is to turn the
machine off if there is not enough water in the
machine.
·When the water level in the reservoir falls
below the tip of the water level sensor, the
machine will “shut down”
·After a 6 minute delay, if the water refills the
reservoir, the machine will start up again.
Separate from the circuit board:
·If the high pressure control (cut out switch)
opens, the compressor will stop immediately
(through the contactor ). It must be manually
reset.
·The master switch is the manual control for the
complete machine, but it is not a service
disconnect.
Ice Vending
·When a user places a container in front of the
Touch Free ice sensor and below the ice
delivery chute, the circuit board connects power
to the bin drive motor and ice is dispensed for
as long as the container is present. If the user
does not remove the container, ice will be
dispensed for 60 seconds and then stop.
·When a user places a container in front of the
Touch Free water sensor, and below the water
spout, the circuit board connects power to the
water solenoid valve and water is dispensed. If
the user does not remove the container water
will be dispensed for 90 seconds and then stop.
Splash panel cleaning:
·A switch, located next to the water spout, may
be pushed to disable the Touch-Free sensors
for splash panel cleaning. It automatically resets
after 2 minutes, or, if pushed within the 2
minutes, resets the circuit board to enable the
Touch Free sensors.
MDT5N25 & MDT5N40
May 2001
Page 13
Splash Panel
Cleaning or
Touch Free
Disable Switch

OPERATION: Water
Water enters the machine through the 3/8" male
flare at the rear of the cabinet, goes to a strainer
and then to the water reservoir which it enters
through the float valve. The water then goes out
the bottom of the reservoir tank to the bottom of
the evaporator.
Reservoir overflow, evaporator condensation and
water in the sink are all routed to the drain. Water
cooled models have a separate water circuit for the
cooling water: it enters the fitting at the rear, goes
to the water regulating valve, then to the water
cooled condenser and down the drain.
There is also an additional water circuit to an
electric valve. When the Touch Free system
senses a container for water, it closes a circuit to
the electric water valve, and water is dispensed.
MDT5N25 & MDT5N40
May 2001
Page 14
WATER RESERVOIR
WATER INLET
WATER DRAIN
WATER LINE FOR
WATER STATION
WATER
LEVEL
Note: The correct water level is determined when
the machine is operating. Check the water level and
compare it to the line molded into the side of the
reservoir. The water level should be between “
above and " below the line.
If needed, adjust the water level by bending the
float arm.

OPERATION: Refrigeration
Beginning at the compressor, the refrigerant is
compressed into a high temperature gas. The
discharge line directs this gas to the condenser. At
the condenser (air or water cooled) the gas is
cooled by either air or water and it then condenses
into a liquid. This high pressure liquid then goes
through the liquid line to the expansion valve.
The thermostatic expansion valve meters liquid
refrigerant into the evaporator, the volume of liquid
refrigerant depending upon the temperature of the
evaporator; warmer evaporators get more
refrigerant and colder evaporators get less.
At the evaporator, the refrigerant enters an area of
relatively low pressure, where it can easily “boil off”
or evaporate. As it evaporates, it absorbs heat
from the evaporator and whatever is in contact with
it (such as the water inside it). After the evaporator,
the refrigerant, now a low pressure vapor, goes
through the suction line back to compressor, where
the cycle is repeated.
MDT5N25 & MDT5N40
May 2001
Page 15
CONDENSER
COMPRESSOR
THERMOSTATIC
EXPANSION VALVE
EVAPORATOR
SUCTION LINE
DISCHARGE
LINE
LIQUID LINE
REFRIGERATION
SCHEMATIC

OPERATION: Ice Vending
Dispensing takes place when the
Touch Free sensor’s infrared beam
bounces back to the sensor from a
container placed directly in front of
it.
If the container is in front of the
Touch Free sensor on the left side,
the ice dispensing vane will rotate
and sweep ice over the ice
dispensing chute: ice will continue
to discharge out this chute as long
as the vane is turning. It stops
when the dispensing vane stops.
If the container is in front of the
Touch Free sensor on the right
side, the inlet water valve will open
and water will flow into the
container.
MDT5N25 & MDT5N40
May 2001
Page 16
ICE DISPENSING
VANE
BIN BOTTOM
DRIVE
MOTOR
ICE CHUTE
TOUCH FREE
SENSOR
SINK
The Touch Free System:
Hold or Place a Container in Front
of The Touch Free Sensor & Under
The Ice or Water Spout;
Ice or Water Will Be Dispensed
Without Touching The Dispenser
TOUCH FREE
SENSOR

MDT5N25 & MDT5N40
May 2001
Page 17
DISPENSE AREA SANITATION
The dispense area; spouts, sink, grill and splash
panel will need periodic cleaning and maintenance.
1. The ice chute may be pulled down to remove it
from the ice dispenser. Wash and sanitize it.
2. The sink grill may be removed for washing and
sanitizing.
3. The sink should be flushed with hot water and
wiped clean with sanitizer.
4. The splash panel requires special attention to
clean it.
·Push and release the Splash Panel Cleaning
switch located to the left of the water spout. This
disables the Touch Free sensors so the splash
panel may be cleaned without vending ice
and/or water.
·Wash the splash panel and wipe with with
sanitizer.
·Re-push the clean switch or allow 2 minutes to
pass for the Touch Free system to reset.
Splash Panel
Cleaning or Touch
Free Disable Switch
Push and Release

CLEANING and SANITIZING
A Scotsman Ice System represents a sizable investment of time and money in any company’s
business. In order to receive the best return for that investment, it MUST receive periodic
maintenance.
It is the USER’S RESPONSIBILITY to see that the unit is properly maintained. It is always preferable,
and less costly in the long run, to avoid possible down time by keeping it clean; adjusting it as needed;
and by replacing worn parts before they can cause failure. The following is a list of recommended
maintenance that will help keep the machine running with a minimum of problems.
Maintenance and Cleaning should be scheduled at a minimum of twice per year.
Sanitizing of the ice storage bin should be scheduled for a minimum of 4 times a year.
Electrical power will be ON when doing in place
cleaning.
ICEMAKING SYSTEM: In place cleaning
1. Check and clean any water treatment devices, if
any are installed.
2. Remove screws and remove the upper front
panel.
3. Move the ON-OFF switch to OFF.
4. Remove the cover to the ice storage bin, and
remove the ice.
5. Remove the cover to the water reservoir and
block the float up.
6. Drain the water reservoir and freezer assembly
using the drain tube attached to the freezer water
inlet. Return the drain tube to its normal upright
position and replace the end cap.
7. Prepare the cleaning solution: Mix eight ounces
of Scotsman Ice Machine Cleaner with three quarts
of hot water. The water should be between 90-115
degrees F.
8. Slowly pour the cleaning solution into the water
reservoir until it is full. Wait 15 minutes, then
switch the master switch to ON.
9. As the ice maker begins to use water from the
reservoir, continue to add more cleaning solution to
maintain a full reservoir.
10. After all of the cleaning solution has been
added to the reservoir, and the reservoir is nearly
empty, switch the master switch to OFF.
11. After draining the reservoir, as in step 6, wash
and rinse the water reservoir.
To Sanitize:
Repeat steps 8-11, only use an approved sanitizing
solution in place of the cleaning solution. A
possible sanitizing solution to use could be 1
ounce of household bleach mixed with 2 gallons of
warm (95oF.-115
oF.) water.
12. Remove the block from the float in the water
reservoir.
13. Switch the master switch to ON
14. Continue ice making for at least 15 minutes, to
flush out any cleaning solution. Check ice for acid
taste - continue icemaking until ice tastes sweet.
DO NOT USE any ice produced from the
cleaning solution.
Be sure no ice remains in the bin.
15. Remove all ice from the storage bin.
16. Add warm water to the ice storage bin and
thoroughly wash and rinse all surfaces within the
bin.
17. Sanitize the bin cover, dispensing vane, bin
bottom, and interior with an approved sanitizer
using the directions for that sanitizer.
18. Replace the ice storage bin cover, and the front
panel.
MDT5N25 & MDT5N40
May 2001
Page 18
Scotsman Ice Machine
Cleaner contains acids.
These compounds may
cause burns. If swallowed,
DO NOT induce vomiting.
Give large amounts of
water or milk. Call
Physician immediately. In
case of external contact,
flush with water. Keep out
of the reach of children.

MAINTENANCE AND CLEANING
1. Air Cooled Models: Check the air cooled
condenser for lint, dirt or grease build-up. Clean
with vacuum or soft brush until light can be seen
thru the fins.
2. The ice machine senses water level by a probe
located in the water reservoir. At least twice a year,
the probe should be removed from the reservoir,
and the tip wiped clean of mineral build-up.
3. The bin control uses devices that sense light,
therefore they must be kept clean enough so that
they can “see”. At least twice a year, remove the
bin control sensors from the grommets in the ice
chute, and wipe them clean.
4. The bearing in the breaker should also be
checked at least two times per year.
A. Check the bearing by:
·removing the ice chute cover
·unscrewing the ice sweep
·removing the water shed
·unscrewing the breaker cover.
·unscrewing the auger stud
Inspect the assembly, looking for wear.
See Removal and Replacement to replace bearing
or seals. Reverse to reassemble.
5. Check and tighten all bolts and screws.
MDT5N25 & MDT5N40
May 2001
Page 19
CLEAN WATER
SENSOR PROBE
CAUTION
THE TIP IS
MADE OF GLASS
Slide UP To
Remove
Reservoir
ICE SWEEP
BIN CONTROL
SENSOR
BIN TOP
BIN CONTROL
SENSOR
Moving Parts Hazard.
Disconnect electrical
power to the icemaker -
dispenser before
beginning.

MAINTENANCE AND CLEANING
In some areas, the water supply to the ice maker
will contain a high concentration of minerals, and
that will result in an evaporator and auger
becoming coated with these minerals, requiring a
more frequent removal than twice per year. If in
doubt about the condition of the evaporator and
auger, the auger can be removed so the parts can
be inspected.
Note: Water filters can filter out suspended solids,
but not dissolved solids. “Soft” water may not be
the complete answer. Check with a water treatment
specialist regarding water treatment.
For more information on removal of these
parts, see REMOVAL AND REPLACEMENT.
1. To remove the auger, remove the front and top
panels.
2. Push bail clamp off of cover and remove cover.
3. Unscrew and remove ice sweep.
4. Remove ice chute from evaporator.
5. Remove 4 allen screws holding breaker to
evaporator.
6. Pull up to remove auger.
After the auger has been removed, allow the auger
to dry: if the auger is not bright and shiny, it must
be cleaned.
Clean the auger and evaporator as required. DO
NOT HONE THE EVAPORATOR.
7. Replace the water seal.
8. Reverse to reassemble.
MDT5N25 & MDT5N40
May 2001
Page 20
ALLEN
HEAD
SCREWS
BREAKER
AND AUGER
ASSEMBLY
Moving Parts Hazard.
Disconnect electrical
power to the icemaker -
dispenser before
beginning.