Scotsman MV Series Installation guide

MV SERIES
MV SERIES
CUBERS
CUBERS
TECHNICAL SERVICE TRAINING
TECHNICAL SERVICE TRAINING
Welcome to another
Welcome to another Scotsman Scotsman technical technical service service presentation presentation. .This This
one will
one will cover cover the the NEW MV NEW MV Series Modular Ice Cube Machines Series Modular Ice Cube Machines
models
models MV 300, MV 300, MV 450 , MV 600 MV 450 , MV 600 and and MV 1000 MV 1000. .

TOPICS
TOPICS
On the next slides are shown the following steps by steps
procedures:
•
•UNPACKING UNPACKING
•
•INSTALLATION INSTALLATION
•
•START UP AND OPERATIONAL CHECKS START UP AND OPERATIONAL CHECKS
•
•OPERATING PRINCIPLES and COMPONENTS OPERATING PRINCIPLES and COMPONENTS
•
•MAINTENANCE MAINTENANCE
•
• SERVICE ANALYSIS
SERVICE ANALYSIS
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
UNPACKING
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
The machines are
supplied in a carton box
secured by two plastic
strips to a wooden base.
Check first the outside
conditions of carton box
and wooden base then cut
the two plastic strips,
remove the tape and then
the carton box. MV 300
MV 300
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
MV 450-600-1000
MV 450-600-1000
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
Visually inspect the
exterior of the machine
then remove the front
panel…. ………
……..and
the two
side
panels …..
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
Remove the
water inlet
and outlet
hoses as well
as……..
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
……….the air
baffle on the
air cooled
version.
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
Unscrew the
unit frame
from the
wooden
base….
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
The Modular Cuber machines
require for the installation the use of
a companion storage bin to store the
ice produced.
Storage bins required are:
•B 193 for MV 300
•B 393 for MV 450-600-1000 B 193
MV 300-450-600-1000
MV 300-450-600-1000

UNPACKING
UNPACKING
Unpack the
storage bin and
visually inspect
the exterior then
remove from
the inside the
carton box
containing the
legs as well as
the drain hose
and the plastic
scoop.
MV 300-450-600-1000
MV 300-450-600-1000

INSTALLATION
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

On B 193/393
Storage Bin
install the four
legs and their
adjusting
leveling nuts on
the bottom base.
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

Place the
storage bin in its
definitive
location then
install on top of
its upper side
the rubber
gasket then….
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

…...install on top of
the same the ice
machine and secure
it with the two
screws.
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

Remove the
plastic tape
securing the
plastic cover
to the vertical
evaporator
then….
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

…..remove
one O ring
and the plastic
cover.
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

Take out the
adhesive tape
holding the
Ice Thickness
Sensor to the
front cells of
the evaporator
then re-install
the plastic
cover with its
O ring.
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

On air cooled
version
unloose the
three screws
securing the
air cooled
condenser to
the unit
frame….
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000

…. and install
the metal plate
(air baffle) on
the back side
of the
machine so….
INSTALLATION
INSTALLATION
MV 300-450-600-1000
MV 300-450-600-1000