Screen Innovations ZERO EDGE PRO User manual

INSTALLERS: PLEASE BE SURE TO LEAVE THIS
MANUAL WITH THE OWNER. THANK YOU!
ZERO EDGE PRO
Owner’s Manual

2
ZERO EDGE PRO
APPLY S/N
STICKER HERE
Screen Innovations warrants its products, to the original purchaser only, to be free from defects in
materials and workmanship for a period of one (1) year from the date of purchase by the original
purchaser provided they are properly operated according to Screen Innovations' instructions and are not
damaged due to improper handling or treatment after shipment from the factory.
This warranty does not apply to equipment showing evidence of misuse, abuse, or accidental damage,
or which has been tampered with or repaired by a person other than authorized Screen Innovations
personnel.
Screen Innovations’ sole obligation under this warranty shall be to repair or to replace (at Screen
Innovations’ option) the defective part of the merchandise. Returns for service should be made to
your Screen Innovations' dealer. If it is necessary for the dealer to return the screen or part to Screen
Innovations, transportation expenses to and from Screen Innovations are payable by the purchaser and
Screen Innovations is not responsible for damage in shipment. To protect yourself against damage or
loss in transit, insure the product and prepay all transportation expenses.
This warranty is in lieu of all other warranties, express or implied, including warranties as to tness
for use and merchant ability. Any implied warranties of tness for use, or merchantability, that may be
mandated by statute or rule of law are limited to the one (1) year warranty period. This warranty gives
you specic legal rights, and you may also have other rights, which vary from state-to-state. No liability
is assumed for expenses or damages resulting from interruption in operation of equipment, or for
incidental, direct, or consequential damages of any nature.
In the event that there is a defect in materials or workmanship of a Screen Innovations product, you may
contact our Sales Partners at 9715-B Burnet Road Suite 400, Austin, TX 78758, [phone].
Important: this warranty shall not be valid and screen innovations shall not be bound by this warranty if
the product is not operated in accordance with screen innovations' written instructions.
Keep your sales receipt to prove the date of purchase and your original ownership.
Limited 1 year warranty
on Screen Innovations products

ZERO EDGE PRO
3
For more technical support questions - Call: 512.832.6939 or
email: suppor[email protected]
Hours of Support: 7:30am - 5pm CST
screeninnovations.com
Please visit support.screeninnovations.
com where you can nd cut sheets,
Installation instructions, spec sheets, tech
notes, guides, drivers and tutorial videos.
Table of Contents
SUGGESTED PROJECTOR PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
STANDARD FRAME PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
STANDARD FRAME ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SPLIT FRAME PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SPLIT FRAME ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LED LIGHTS ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
BLACK DIAMOND OR SHORT THROW ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
SLATE OR PURE ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
BLACK BACKER ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MAESTRO ATTACHMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
BLACK BACKER ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
SMALL TRIM ATTACHMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
MEDIUM OR LARGE TRIM ATTACHMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
LOGO ATTACHMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
TRIM REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
WALL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
FLOWN INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
IR LIGHTING HEX CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
IP CONTROLLED LIGHTING SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4
ZERO EDGE PROSUGGESTED PROJECTOR PLACEMENT
11°
11°
SCREEN
Better
Best
Good
36”-42”
(91cm - 106cm)
Please visit our Screen Material Wizard (screeninnovations.com/tools/
screen-material-wizard/ ) for minimum throw distance requirements based
on screen material.

ZERO EDGE PRO
5
SPLIT
STANDARD 6
11
PRE ASSEMBLED 35

6
STANDARD
STANDARD FRAME PARTS LIST
2X
1X
Hardware Kit
1X
1X
2X
2X
(LED Lights Only)
Wall Brackets Mounting
Screws
4X
1/4-20 x 1/4’’
Screws
(Small trim only)
4X Thin Corner
Brackets
4X Thick Corner
Brackets
1/8’’ & 5/32’’
Hex Keys
Bungees
(Maestro only)
4X Gloves
1/2’’ Small trim
option
1 1/2’’ or 2’’
trim option
Acrylic Logo Channel Nut
(AT only)
Thumb
Screws
Corner Alignment
part
(Black Diamond
and Short Throw

7
STANDARD
Flying Mount Only
2X Flown Ceiling
Mount
2X Flown
Cable
LED Remote LED Foam
LED IR Controlled Only
2X Flown Screen
Mount
If IP controlled LED lights are ordered, Phillips Hue hub must be purchased
and set up separately. See page 41 for IP lighting Instructions.

8
STANDARD
1
2
Thin Bracket
Thick Bracket
Insert the thin corner brackets into the outside channels and the thick corner brackets
into the inside channels of the vertical frames. Then slide into the channels in the
horizontal frames.
STANDARD FRAME ASSEMBLY
NOTE: If using AT or Maestro material then check to make
sure the channel nuts are installed in the inner channel
before proceeding.

9
STANDARD
4
3
Make sure the points on the frame pieces line up. Then nger tighten 2 of the set screws
to lock in the corners.

10
STANDARD
6
5
A = B
AB
18 19
LED
Measure the diagonals to check if frame is square. If one diagonal is longer then push
on the corners at that diagonal. Tighten all set screws once the diagonals are equal to
within 1/8’’.

11
SPLIT
SPLIT FRAME PARTS LIST
1X 1X
1X 1X
2X
2X 2X
2X
1X
1X
(LED Lights Only)
1/2’’ Small trim
option
1 1/2’’ or 2’’
Trim option
Hardware Kit
Wall Brackets Mounting
Screws
4X
1/4-20 x 1/4’’
Screws
(Small trim only)
4X Thin Corner
Brackets
4X Thick Corner
Brackets
1/8’’ & 5/32’’
Hex Keys
Bungees
(Maestro only)
4X Gloves Acrylic Logo Channel Nut
Thumb
Screws
Corner Align-
ment part

12
SPLIT
Flying Mount Only
LED IR Controlled Only
If IP controlled LED lights are ordered, Phillips Hue hub must be purchased
and set up separately, see page 46 for IP lighting Instructions.
2X Flown Ceiling
Mount
2X Flown
Cable
LED Remote LED Foam
2X Flown Screen
Mount

13
SPLIT
1
2
Thin Bracket
Thick Bracket
Insert the thin corner
brackets into the outside
channels and the thick
corner brackets into the
inside channels of the
vertical frames. Then slide
into the channels in the
horizontal frames.
SPLIT FRAME ASSEMBLY
NOTE: If using AT or Maestro material then check to make
sure the channel nuts are installed in the inner channel
before proceeding.

14
SPLIT
3
4
Slide the horizontal frame pieces together and secure with the splice bars. Then attach
the vertical support to the frame as shown.

15
SPLIT
5
6
Make sure the points on the frame pieces line up. Then nger tighten 2 of the set screws
to lock in the corners.

16
SPLIT
7
8
A = B
AB
17 19
LED
Measure the diagonals to check if frame
is square. If one diagonal is longer then
push on the corners at that diagonal.
Tighten all set screws once the diagonals
are equal to within 1/8’’.

ZERO EDGE PRO
17
LED LIGHTS ATTACHMENT
1
Connect the lighting harness
with the included screws to
the nuts in the frame piece
with the lights attached to it.
NOTE: Steps 1 and 2 will have already been completed if possible to be shipped that way.
If so skip to step 3.
Plug in the lights to the
controller plugs.
2
If IP controlled LED lights are ordered, Phillips Hue hub must be purchased
and set up separately, see page 50 for IP lighting Instructions.

18
ZERO EDGE PRO
3
Cut the light strips at the copper pad as indicated to
the correct length such that they just overlap at the
middle of the top frame piece. DO NOT cut the light
strips at any other location.
+12V
B
G
R
+12V
B
G
R
CUT HERE
Press in the lights to the channel on the frame. LED foam must be used when rounding
the corners. Failure to do so will damage the LED strips

ZERO EDGE PRO
19
Material?
BLACK DIAMOND or
SHORT THROW
23
MAESTRO
25
SLATE or PURE
20

SLATE or PURE
20
1
2
SLATE OR PURE ATTACHMENT
Wear gloves when handling material. Carefully unroll the screen material out onto a
clean oor. Take care to not bend or crease the screen material.
Carefully lie the frame onto the screen material. Center the frame about the screen
material.
Non AT Material AT Material and Black Backer