SCS 3000 Series User manual

TB-9039 Page 1 of 2 © 2015 DESCO INDUSTRIES, INC.
Employee Owned
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • [phone] • Website: StaticControl.com
Grounding Accessories 3000 Series
Instructions Sheet
July 2015
USER GUIDE TB-9039
Your choice of four kits to meet
almost any grounding need
In any area where static-sensitive electronic components
or boards are handled, proper static protection is
essential. A variety of static control devices are available
to meet the requirements necessary to protect both the
electronics and the people handling them. But these
devices require proper grounding to perform their
functions. These four kits cover a variety of possible
uses, from single-point grounding to multiple points
connected to a common ground.
3048 Wrist Strap/Table Mat Grounding
System
Two wrist straps can be connected to the Wrist Strap/
Table Mat Grounding System. The 15 foot (4.6 m)
ground cord is connected directly to hard ground.
Snapping the Grounding System to either of the two
connectors in the corners of the table mat provides
reliable, common point grounding for the wrist straps and
the table mat simultaneously.
3047 Common Point Grounding
System
To provide true common point grounding for all
workstation components, the kit 3047 offers a single-row,
six-terminal strip. No additional components offering
resistance are in the path on any link of the static
protection system. Hard grounds are available on the six
terminals. The system is easily accessible, and mounts on
any at surface in new or existing workstation
environments. The protective cover is connected to
ground via a one-megohm resistor for the maximum
in personnel safety. In addition, three cable clips are
included to aid you in ground cord management.
Figure 1. 3048 Wrist Strap/Table Mat Grounding System.
Terminal Strip
Laminate
#6 Double
Studded
Screw
Wear Layer
Black Conductive Layer
Figure 2. 3047 Common Point Grounding System.
Figure 3. Installing the 3047 Common Point Grounding
System (top).
Laminate
Hole “A”
Terminal Strip
#6 Double
Studded Screw
Cover
Hole “B”
Wear Layer
Black
Conductive
Layer
Figure 4. Installing the 3047 Common Point Grounding
System (bottom).
Wrist Strap/Table Mat
Grounding System
3050 Snap
Fastener
Dissipative Table Mat

TB-9039 Page 2 of 2 © 2015 DESCO INDUSTRIES, INC.
Employee Owned
SCS - 926 JR Industrial Drive, Sanford, NC 27332 • [phone] • Website: StaticControl.com
3042 Wrist Strap Grounding System
Grounding of two wrist straps using a common point to
ground is possible with the system 3042. It is easy to
identify for this purpose, with a clearly visible ground
symbol. Compact in size, it mounts to any at surface
where a wrist strap needs to be connected to a reliable
ground. The kit may be mounted on new workstations or
retrotted onto any existing workstation. Components of
the kit include one static dissipative engineering grade
plastic housing, one 10-foot (3 m) grounding cord with
multi stud ring terminal, strain relief for the grounding
cord, two banana jacks built into the housing, and two #8
galvanized, self-tapping Phillips screws.
3041 Grounding Kit
To properly ground a workstation with Static Protective
Hard Laminate, this kit gives you a choice of four methods
to provide proper grounding. This can be accomplished
from the top or the bottom of the work surface. Contents
of the kit include the hardware needed to establish reliable
connections to ground.
Cable Clip
Table TopSolderless
Ground Wire
Ground
Respectable
#8 x 1 1/2"
Self-tapping Phillips
Head Screws
Figure 5. 3042 Wrist Strap Grounding System.
Figure 6. Installing 3042 Wrist Strap Grounding System.
Figure 7. 3041 Grounding Kit.
Ground From Top
Ground From Top With Wing Nut
Ground Cord #10 Screw
Internal Star Lock
Washer
#10 Nut Internal Star Lock
Washer
Ground Cord
Wing Nut
#10 Nut
Internal Star
Lock Washer
#10 Screw
Figure 8. Installing 3041 Grounding Kit from top.
Internal Star Lock Washer #10 Screw
Internal Star Lock Washer
Ground Cord
Ground From Bottom
#10 x 3/4" Self-tapping Screw
Internal Star
Lock Washer
Ground Cord
Ground From Top Self-tapping Screw
Figure 9. Installing 3041 Grounding Kit from bottom and
with self-tapping screw.
Important Notice
Before using this product, you must evaluate it and
determine if it is suitable for your intended application.
You assume all risks and liability associated with such
use.
Limited Warranty, Warranty Exclusions, Limit of
Liability and RMA Request Instructions
See the SCS Warranty -
http://staticcontrol.descoindustries.com/warranty.aspx