Sealey WB85 User manual

85L WHEELBARROW
MODEL NO: WB85
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Always distribute the load evenly over the surface of the wheelbarrow.
8DO NOT overload the wheelbarrow.
8DO NOT use wheelbarrow on uneven ground and DO NOT run over curbs or steps - use a ramp.
8DO NOT allow others to ride in the wheelbarrow.
8DO NOT use the wheelbarrow if any part is damaged, paying particular attention to the wheel.
8DO NOT inflate the tyre to more than 25psi.
2. INTRODUCTION
Manufactured from heavy-duty composite material. Ideal for a wide range of gardening and light construction tasks as well as general domestic
use. Constructed with strong tubular steel frame and rubber grip handles. Fitted with 405mm pneumatic tyre.
3. SPECIFICATION
Model No.: ................................................................... WB85
Capacity........................................................................... 85L
Capacity (Weight) ........................................................ 150kg
4. CONTENTS
5. ASSEMBLY
NOTE: Component package is wrapped in lm and placed inside the
cross member of the frame (g.1.2).
5.1. FRAME AND PAN SUPPORT (g.2)
5.1.1. Carefully remove plastic wrapping from the frame.
5.1.2. Carefully remove component package from cross member.
5.1.3. The pan support arm (g.1.3) is already engaged with the frame. This
will need adjustment at the nal stage of assembly.
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear protective
gloves
Wear safety
footwear
g.2
WB85 Issue 1 30/07/20
g.1

5.2. WHEEL ASSEMBLY (g.3)
5.2.1. Assemble shaft (g.1.4) into wheel hub and place between the
wheel mounting brackets. Align the shaft with either of the two holes
in the mounting brackets.
5.2.2. Place plastic caps (g.1.6) onto wheel hub centres and engage
bolt and washer arrangement (g.1.E) in shaft. Tighten bolts to secure
in place
5.3. PAN AND FRAME ASSEMBLY (g.4)
5.3.1. Partially invert pan to allow internal access to the xing holes.
5.3.2. Pass screws (g.1. A) from inside the pan, through the frame xing
holes, and engage plain washer, spring washer and nut pack
(g.1.D / B / C) on outside.
8DO NOT tighten the xings until all xings, including the one
shown in g.5, are in place and engaged.
5.4. FRONT SUPPORT ASSEMBLY (g.5)
5.4.1. Adjust the location of the support to enable alignment of the hole
in the support to match with the xing hole in the pan.
5.4.2. Pass the screw (g.1.A) through the pan from the inside to the outside
and engage plain washer, spring washer and nut pack (g.1.D / B / C).
5.5. FINAL ASSEMBLY
5.5.1. With all xings in place apply nal tightening to all xings.
8DO NOT over tighten.
WB85 Issue 1 30/07/20
Original Language Version
© Jack Sealey Limited
g.3
g.4
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Parts support is available for this product. Please email [e-mail] or telephone [phone]
g.5