Sealey SPP01.V2 User manual

SOLAR PANELS
MODEL NO’S: SPP01.V2 (12V/1.5W), SPP02.V1 (12V/2.4W),
SPP03.V2 12V/4.8W
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
9Observe standard safety procedures when using these items.
▲DANGER! - Beware, lead-acid batteries generate explosive
gases during normal battery operation.
9If the battery terminals are corroded or dirty, clean them before
attaching the clips.
9 Removeillttingclothing.Removeties,watches,ringsand
other loose jewellery. Contain, or tie back, long hair when
working near batteries.
9Keep children and unauthorised persons away from connections.
WARNING!: DO NOT use solar panels on any vehicles other than
those with12Volt DC systems.
8DO NOT dis-assemble solar panel. The solar panel must be
 checkedbyqualiedservicepersonnelonly.
8DO NOT get solar panel wet or use in damp locations or areas
where there is condensation.
8DO NOT use the solar panel for any purpose other than for which
it is designed.
8DO NOT pull the cables or clips from the battery terminals.
8DO NOT operate the solar panel if damaged.
9When not in use store in a safe, dry, childproof location.
2. INTRODUCTION
Amorphous solar panels convert daylight directly into 12V electricity. Suitable for maintaining charge in a wide range of batteries and power
packs. Ideal for batteries stored in boats and caravans and for batteries in vehicles in long-term storage. IP44 Rating (non-waterproof). For
use behind car windscreen or other protection. Supplied with battery clips and vehicle accessory socket plug (only suitable for vehicles with
“permanent live” accessory socket).
3. SPECIFICATION
Model no:..............................................................SPP01.V2
Output: ................................................................... 12V/1.5W
Dimensions: ......................................................350 x 125mm
IP Rating .........................................................................IP44
Model No...............................................................SPP02.V1
Output .................................................................... 12V/2.4W
Dimensions: ......................................................375 x 215mm
IP Rating: ........................................................................IP44
Model no:..............................................................SPP03.V2
Output: ................................................................... 12V/4.8W
Dimensions: ......................................................440 x 345mm
IP Rating .........................................................................IP44
4. OPERATION
4.1. INSTALLATION
4.1.1. Insertthesuctioncups(SPP01.V2,SPP02.V1only)intothepre-drilledendsofthesolarpanelensuringthattheyaresecurelyxed.
Choose a clean, dry surface, facing the sun, then dampen suction cups and mount to vehicle’s dash or windscreen.
4.2. CONNECTION THROUGH VEHICLE ACCESSORY SOCKET (Only suitable for vehicles with “permanent live” accessory
socket)
4.2.1. Attach the auxiliary adaptor lead to the solar panel lead. Plug the male-end of the auxiliary adaptor (12V plug) into the female auxiliary
socket (in the vehicle) making sure that both ends are secure and aligned correctly. For optimal charging power, ensure the panel
(solar cell up) is directly facing the sun. For vehicles that do not have permanent live accessory sockets refer to:
SPP01.V2, SPP02.V1, SPP03.V2 Issue:3 (3,4) 11/06/20
Original Language Version
© Jack Sealey Limited
Refer to
instruction
manual
Connect to any 12V auxiliary
power outlet
Connect directly to battery
using DC cables
Connect to any 12V auxiliary
power outlet
Connect directly to battery
using DC cables

4.3. WATERTIGHT HARDWIRED TERMINAL CONNECTOR (SPP01.A) FOR SPP01.V2, SPP02.V1 AND SPP03.V2 (NOT SUPPLIED),
SEE BELOW.
4.4. BATTERY CONNECTION
NOTE: Check the battery is 12V DC. DO NOT use with a 24V battery.
4.4.1. Attach the battery clip lead to the solar panel lead.
4.4.2. Ensure the battery terminals are clean, if necessary clean away any corrosion.
4.4.3. Clip the red (+) crocodile clip to the red (+) terminal post on the battery.
4.4.4. Clip the black (-) crocodile clip to the black (-) terminal post on the battery.
WARNING!:Whendisconnectingremovetheblack(-)clipfromthebatteryrstthenremovethered(+)clip.
4.4.5. Batteryterminalconnectionleadwithin-linefuseunitandweatherproofcaptoo󰀨erprotectionfromwateringresswhentheconnector
is not in use. Can be left on the vehicle and simply connected to SPP01.V2, SSP02.V1 and SPP03.V2 when required.
WARNING!: The clips MUST be placed on to the battery in the aforementioned order, wrong connections may cause sparking or
explosion.
NOTE: This solar panel has a built-in blocking diode that protects the battery from reverse discharge.
NOTE: The use of the solar panel is not recommended while the vehicle is in use.
NOTE: The solar panel is not weatherproofed - DO NOT use in wet or use in damp locations.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
Original Language Version
© Jack Sealey Limited
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
SPP01.A
(Not Supplied)
Parts support is available for this product. Please email [e-mail] or telephone [phone]
SPP01.V2, SPP02.V1, SPP03.V2 Issue:3 (3,4) 11/06/20