Sealey Siegen Tools S01167 User manual
9L MANUAL VACUUM OIL & FLUID
EXTRACTOR
MODEL NO: S01167
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are strictly adhered to when using this
equipment.
WARNING!
Ensure that you wear protective clothing, gloves, goggles, face mask as appropriate for the fluid being extracted.
9Keep the extractor clean and maintain it in good condition (use an authorised service agent).
9Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
9Check extractor connections and fittings before use. When the extractor is being used, check that there are no leaks.
9Ensure that the extractor’s tank capacity exceeds the amount of fluid to be collected.
9Avoid unintentional starting of the extractor and ensure that the end of the suction tube is fully submerged in the fluid before operating.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
9Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9Keep children and unauthorised persons away from the working area.
9Dispose of waste fluids in accordance with local authority regulations.
9Use only to extract engine or transmission oils, or similar NON-corrosive fluids. Unit may also be used for the transfer of water.
WARNING! DO NOT allow uncontrolled discharge of fluids thus polluting the environment.
8DO NOT pull or yank any pipes or hoses and do not attempt to move the extractor by pulling the hose.
8DO NOT leave the extractor operating unattended.
8DO NOT use to extract hazardous or harmful chemicals, solvents, petrol, diesel, kerosene, alkaline or acids. If by chance such fluids
are used in the unit, it must be immediately drained and thoroughly cleaned. Use with prohibited fluids will invalidate your warranty.
8DO NOT store fluids in the extractor’s tank. After extracting fluid, it must be emptied into an approved receptacle as soon as possible.
8DO NOT dismantle, tamper or adapt the extractor for any purpose other than for which it is designed.
8DO NOT store in areas of high temperature, direct sunlight, rain or snow.
8DO NOT leave the unit in a pressurised state.
WARNING! When the extractor’s tank contains liquid that is under pressure DO NOT remove or insert the extension tube connector into
the inlet/outlet fitting as this may result in a sudden discharge of liquid that could be dangerous.
9Always press the pressure relief button before connecting or disconnecting the extension tube or inlet coupling.
2. INTRODUCTION
9L Capacity device constructed from composite materials. Uses manual pump to generate vacuum. Suitable for the extraction of all
types of engine, transmission and lubricating oil from cars, motorcycles, marine engines, stationary engines and industrial machinery.
Alsosuitableforlowviscosityuidssuchaswater.SuppliedwithØ4,Ø6,Ø8andØ10mmsuctionprobes,andØ4x600mm
brass extension tube. Uses probes to extract engine oil through the dipstick tube.
3. SPECIFICATION
Model No:.................................................................. S01167
Capacity:........................................................................... 9 L
Suction probes: Ø4x1000,Ø6x1000,Ø8x1000,Ø10x1000mm
Extension tube: ........................................BrassØ4x600mm
4. OPERATION
4.1. SET UP FOR OIL CHANGE
NOTE:Ensureyouread,understandandapplytheSection1SafetyInstructionsand
consult manufacturer’s workshop manual for any specific procedures.
4.1.1. Ensure that the vehicle is level. Run the engine for approximately five minutes to ensure
that the oil is warm. Switch off engine.
4.1.2. Remove the oil dipstick from the engine.
4.1.3. Insert the appropriate extracting probe into the dipstick
tube making sure it reaches the bottom of the sump.
4.1.4. Connect the extracting probe to the extension tube using its
black plastic adaptor. The tubes are a push fit into the adaptor.
S01167Issue125/10/19
Original Language Version
© Jack Sealey Limited
Refer to
instructions
Wear eye
protection
Wear protective
gloves
4.1.5. Position the extractor unit close to the front or side of the
vehicle.Pressfitthe10mmdiametersuctiontubeadaptorto
theinletcoupling(fig.1).
WARNING! Ensureoiltemperaturedoesnotexceed70°C.
4.2. DRAWING FLUID INTO THE EXTRACTOR
NOTE: Before operating the extractor you must press the
pressurereleasevalve(fig.1)todissipateanyvacuumor
pressure remaining in the tank from previous use.
4.2.1. To commence suction, place your foot over the foot rest to
steady the unit and start to pump the handle up and down
through its full travel. As you pump up and down, the tank
will begin to fill. Stop pumping and press release valve to
prevent the unit overfilling.
4.3. EMPTYING THE EXTRACTOR
NOTE: Before emptying the extractor you must press the
pressurereleasevalve(fig.1)todissipateanyvacuumor
pressure remaining in the tank.
4.3.1. Carefully remove the suction probe from the dipstick tube using rag or tissue to prevent any oil drips soiling the engine bay. Replace
the dipstick.
4.3.2. Disconnectthesuctiontubeandtheinletcouplingfromtheextractorbody(g.1).
4.3.3. Empty the extracted fluid into a suitable container. The fluid should be disposed of according to local authority regulations.
8DO NOT tiltbeyond900.
5. MAINTENANCE
5.1. Keeptheunitclean,wipeoffanyuidspillage.Keepthesuctiontubescleanandclearofblockages.Checkthatalltubes,hosesand
connections are in good condition.
S01167Issue125/10/19
Original Language Version
© Jack Sealey Limited
g.1
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty:Guaranteeis12monthsfrompurchasedate,proofofwhichisrequiredforanyclaim.
Partssupportisavailablefortheseproducts.Pleaseemailsales@sealey.co.ukortelephone01284757500
Table of contents
Other Sealey Ventilation Hood manuals
