Seconique Furniture STOCKHOLM 100-103-057 User manual

STOCKHOLM 2 DRAWER BEDSIDE
ASSEMBLY INSTRUCTIONS
SEC/SH/10/18/EU1
DO NOT
USE
FOR DOMESTIC USE ONLY
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF
SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS SAFE ASSEMBLY AND
PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE
FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS
PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY HAVE AND
COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES IT MAY BE
NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME TO TIME. THIS IS
COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET)
DO NOT USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A
PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT MARKING.
PAGE 1

PAGE 2
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF THE CAM
LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO THE
NARROW PART CLOSES OVER THE BOLT.
SEC/SH/10/18/EU1

2
2
1
3
4
4
5
7
6
8
9
10
11
12
13
14
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PART LIST
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START ASSEMBLING. IF
YOU DO FIND THAT SOMETHING IS MISSING, DO NOT CONTINUE ASSEMBLY, PLEASE CONTACT
YOUR SUPPLIER IMMEDIATELY.
PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PILLAR LEG_LEFT 2 PCS
PILLAR LEG_RIGHT
SUPPORT LEG_FRONT & BACK
SUPPORT LEG_LEFT & RIGHT
BOTTOM PANEL
SIDE PANEL_LEFT
SIDE PANEL_RIGHT
BACK PANEL
TOP PANEL
DRAWER BACK
DRAWER SIDE_LEFT
DRAWER SIDE_RIGHT
DRAWER FRONT
DRAWER BASE
2 PCS
2 PCS
2 PCS
2 PCS
2 PCS
2 PCS
2 PCS
2 PCS
1 PC
1 PC
1 PC
1 PC
1 PC
PAGE 3
SEC/SH/10/18/EU1

3
3
A
3
1
1
2
2
I4PCS
HARDWARE NEEDED:
A 20PCS
4
4
A
4
I
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
HARDWARE LIST STEP 1
STEP 1.1
DOWEL 6 X 30MM 44 PCS
BOLT M7 X 60MM 4 PCS
SCREW M3.5 X 12MM 22 PCS
4 PCS
M6X50MM
4 PCSHANDLE SCREW 19MM
8 PCS
ALLEN KEY
CAM BOLT+CAM NUT 8 SETS
PVC GLIDE 4 PCS
SCREW M3.5 X 16MM 12 PCS
4 PCS
4 PCS
HANDLE
1 PC
FLANGE NUT
SPANNER
DRAWER RUNNER A-L/R
DRAWER RUNNER B - L/R
PLASTIC CORNER BLOCK 4 SETS
SCREW M4 X 38MM
2 PCS
1 PC
4 PCS
STEP 1.2
A
B
C
D
E
F
G
H
I
J
L
M
N
O
P
K
PAGE 4
SEC/SH/10/18/EU1

H
6
7
A
6&7
HARDWARE NEEDED:
A8PCS
C 16PCS
H4PCS
K4PCS
3
3
4
42
2
1
1
N
2
3
B
M
HARDWARE NEEDED:
B4PCS
M1PC
N1PC
Upper Second Hole
Last Third Hole
First Hole
SCREW MUST BE INSERTED
IN THE FIRST HOLE ON THE
DRAWER RUNNER
Upper Second Hole
Last Third Hole First Hole
SCREW MUST BE INSERTED
IN THE FIRST HOLE ON THE
DRAWER RUNNER
P
P4PCS
C
K
K
C
3
STEP 3STEP 2
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
A
7
7
6
6
2
PAGE 5
SEC/SH/10/18/EU1
MAKE SURE THE ARROW ON
THE CAM LOCK IS POINTING
TOWARD THE HOLE ON THE
EDGE OF THE PANEL.

STEP 4
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 5
STEP 5.1
5
6
7
9
9
H
H4PCS
HARDWARE NEEDED:
F4PCS
F
M
5
6
ROUND EDGE
FACING UP
M1PC
STEP 4.1
6
7
8
5
141
2
3
6
2
1
3 2
HARDWARE NEEDED:
F4PCS
M1PC
F
M
8
7
5
7
43
5
2
A
A
PAGE 6
SEC/SH/10/18/EU1

H
11&12
13
13
H
A
11&12
H4PCS
10
10
A
STEP 6
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 7
STEP 6.1
9
6
7
5
2
3
1
4
2H
O
HARDWARE NEEDED:
O4SETS
9
6
H
STEP 7.1
STEP 7.2
HARDWARE NEEDED:
A16PCS
H. 4PCS
DRAWER X 2
11&12
8
8
PAGE 7
SEC/SH/10/18/EU1
MAKE SURE THE ARROW ON
THE CAM LOCK IS POINTING
TOWARD THE HOLE ON THE
EDGE OF THE PANEL.

12
10
14
14
J
C
10
14
10 12
HARDWARE NEEDED:
C 6PCS
12
11
10
11
12
10
13
12
10 D4PCS
D
13
G
E
E4PCS
G
J12PCS
L4PCS
L
LAST THIRD HOLE
THIRD HOLE
L
2PCS
H
12
13
13
FINISHED FRONT EDGE
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
DRAWER X 2
STEP 8
STEP 8.1
STEP 8.2
STEP 8.3
STEP 8.4
PAGE 8
SEC/SH/10/18/EU1

STEP 10
X
!CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
STEP 9
PAGE 9
SEC/SH/10/18/EU1