Seconique Furniture CHARLES 5 DRAWER NARROW CHEST User manual

ASSEMBLY INSTRUCTIONS
PAGE 1 OF 9
CHARLES 5 DRAWER NARROW CHEST
SEC/SH/11/16/EU1
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT.ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME.THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE.DO NOT OVERTIGHTEN FIXING.
FOR CLEANING,YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH,DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT.ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
FOR DOMESTIC USE ONLY

PF
PG
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 2 OF 9
SEC/SH/11/16/EU1
( SCREWDRIVER NOT PROVIDED )
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
CAM LOCK IS POINTING TOWARD THE HOLE ON EDGE OF PANEL. )
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK.YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 3 OF 9
SEC/SH/11/16/EU1
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING.IF YOU DO FIND THAT SOMETHING IS MISSING,DO NOT CONTINUE
ASSEMBLY,PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
PARTS LIST PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
LEFT SIDE PANEL
INNER TOP PANEL
BASE PANEL
FRONT CROSSBARS
CENTRE BACK CROSSBAR
RIGHT SIDE PANEL
DRAWER SIDE - LEFT
DRAWER BACK
1 PC
1 PC
1 PC
2 PCS
2 PCS
1 PC
1 PC
1 PC
1 PC
5 PCS
5 PCS
LOWER BASE CROSSBARS
TOP PANEL
BACK PANEL
12
13
DRAWER SIDE - RIGHT
DRAWER FRONT
5 PCS
5 PCS
14 DRAWER BASE 5 PCS
1
8
2
5
5
9
6
7
3
4
4
13
10
11
12
14

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 4 OF 9
SEC/SH/11/16/EU1
HARDWARE LIST
A
B
C
D
E
F
G
H
I
J
K
L
M
DOWEL 6 X 30MM
SCREW M3.5 X 16MM
DRAWER RUNNER B
TACK
EDGE PROTECTOR
ALLEN KEY
HANDLE
HANDLE SCREW M4 X 30MM
46 PCS
74 PCS
4 PCS
20 PCS
10 SETS
5 PCS
10 PCS
DRAWER RUNNER A
10 PCS
10 PCS
1 PC
SCREW M4 X 38MM
2 SETS
30 PCS
BOLT M7 X 60MM 18 PCS
CAM BOLT + CAM NUT
SCREW M4 X 30MM
N
O
2 PCS
2 PCS
ANTI - TIP STRAP
SCREW M4 X 16MM

PD PE
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 5 OF 9
SEC/SH/11/16/EU1
YOU WILL NEED:-
YOU WILL NEED:-
FRONT BACK
UP SECOND HOLE
FIRST HOLE
FRONT BACK
UP SECOND HOLE
FIRST HOLE
C
H
C
H
CC
20 PCS 20 PCS
HH
5 PCS 5 PCS
LAST THIRD HOLE LAST THIRD HOLE
SCREW MUST BE INSERTED
IN THE FIRST
HOLE ON THE DRAWER
RUNNER.
SCREW MUST BE INSERTED
IN THE FIRST
HOLE ON THE DRAWER
RUNNER.
1
7
STEP 1 STEP 2

LJ ( 0.25 )
LK ( 0.28 )
MN ( 0.17 )
NJ ( 0.09 )
NK ( 0.15 )
LJ
LK
MN
MP
NJ
NK
NM
NW
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 6 OF 9
SEC/SH/11/16/EU1
STEP 3 STEP 4.1
STEP 4.2
YOU WILL NEED:- YOU WILL NEED:-
A26 PCS B18 PCS
A
GK
M1 PC
A
M
B
SCREW MUST BE INSERTED IN THE FIRST
HOLE ON THE DRAWER RUNNER.
C
H
A
A
A
7
2
5
5
6
4
34
3
5
52
1
1
7
4
180o
4
4
8
2
3
6
5
5

MR ( 0.25 )
MU ( 0.2 )
NF ( 0.16 )
NP ( 0.2 )
JP
MR
MU
NF
NP
NU
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 7 OF 9
SEC/SH/11/16/EU1
STEP 5 STEP 6.1
C4 PCS
D
YOU WILL NEED:- YOU WILL NEED:-
4 PCS
R
B
PLEASE INSERT THE BACK PANEL INTO THE UNIT
D
G
SIDE VIEW
BEFORE FIXING THE TOP PANEL
PLEASE ALIGN THE TOP PANEL
WITH THE INNER TOP PANEL .
A
2
2
STEP 6.2
G
L
10 PCS
2 SETS
C
L
88
2
1 & 7
8
7
1
5
5
3
4
2
6
9
9
BOTTOM
9

NA ( 0.15 )
NB ( 0.15 )
NC ( 0.23 )
PA ( 0.13 )
PB ( 0.18 )
PC ( 0.28 )
NA
NB
NC
PA
PB
PC
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 8 OF 9
SEC/SH/11/16/EU1
YOU WILL NEED:-
A20 PCS
C 30 PCS
20 PCS
STEP 8
E
F
G
I
J
10 SETS
20 PCS
10 PCS
5 PCS
K
G
I
C
5 X DRAWERS
K 10 PCS
A
E
F
F
I
I
THIRD HOLE
LAST THIRD HOLE
BACK
FRONT
STEP 7.1
STEP 7.2
STEP 7.4
STEP 7.5
F
STEP 7.3
12
10 11
13
13
13
14 14
11&12
11&12
13

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 9 OF 9
SEC/SH/11/16/EU1
WARNING
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
HARDWARE LIST
( N ) Anti-Tip Strap - 2 pc
( O ) M4 X 16MM - 2 pc
TOP
WALL
TOP
WALL
TOP
N
N
O