JWA MADEIRA 68032 User manual

INSERT PAGE NUMBER
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
MADEIRA
68032
Bar Stool

PRE-ASSEMBLYPREPARATION
Before you start:
1. Choosea clean, level, spacious assembly area. Avoid hard surfaces thatmay
damagethe product
2. Take care when lifting. Product should be assembled as near as possibleto the
point of use
3. Ensure that you have all required contents for completeassembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardwareparts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damagethe threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product dueto possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instructions for futurereference.
2
Allow 30 min For 1 persons

1
2
1
Se
at
2
Legs
3
Stretcherbars
4
Connector
PARTS LIST
3
A B C D
M6X19 X4 M4 X1 M6X12 X12 M6X20 X4

STEP1:
4
STEP2:
•Prepare a surface with a protective blanket or cardboard.
•Insert the 2 stretcher bars(3) to one of the legs(2), as shown below.
•Secure with 2x bolt(C) at each connecting point, fasten with Allen key(B).
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
•Attach the connector(4) to the leg as shown below.
•Secure with 2x bolts(C), fasten fully with Allen key(B).
•Repeat for the other leg.

•Stand the stool up the right way up on a level surface.
•Push down on the stool until it levels out. Do not lean beyond your own
balance.
•Once level, flip the stool back over again (upside down). Now fully fasten
all the bolts.
•Do not over tighten, this may damage the product.
STEP3:
5
•Lay the seat(1) on a surface, with the bottom facing up.
•Prepare 4 bolt D sets, by threading bolt(D) through washer(A).
•Place the leg structure onto the seat as show below.
•Secure with 4x bolt D sets, fasten with Allen Key(B).
•Tighten only until the bolt is a little firm in the thread, do not fasten
completely.
STEP4:

6
ASSEMBLYIS COMPLETE

PRODUCTCARE:
7
If the glass is chipped or broken, stop using the produ ct and consult place of purchase
WARNING:
.Donot place very hotor cold items on the glass surface unless adequ atelythick table
mats are used to prevent such items coming in contact W ith theg lass
DOnotsitorstandupontheqlasssurface
DOnotusetheglassasachoppingSurface
DOnotstriketheglassWithhardorpointeditemS
WhencleaningtheglasspanelsuseadampclothorleatherWithWashingupliquidorsoftsoapifne
cessary.D0notuseWashingpoWdersorany
O ther su bs tan ces contain in g abrasives since these m ay scratch the glas S
0 ur fu rn iture is built to last. F ollowin g th ese steps for basic care
shouldprotectyourinvestmentforyearstocome
D ust frequently W ith a clean damp lint-free clo th.This will help rem
oveabrasivebuildupWhichcandamageafinishOVertime
Avoid exposing your furniture to strong sunlight, heat outlet, open
W in dOw S or dampness. Prolonged expo su re to direct sunligh t can fade th efinish of
your furniture, while extreme temperature and humidity chang escan cause crackin g Or
splitting
D O n ot allow plas tic to co me in direct contact W ith your fu rniture .
C hemicals in the plastic of placemats etc. may soften and mark th e
finish ifleftin contact with the furniture for a period of tim e