Classic Exhibits VISIONARY DESIGNS MOD-1703 Manual

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
BACK VIEW FRONT VIEW
MOD-1703 Backlit Counter
If you would like to tell us about your experience with your setup instructions please email us at [email protected]
SETUP INSTRUCTIONS

© 2023
Order #XXXXX
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all set screws
and locks during disassembly.
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED
General Information

© 2023
Order #XXXXX
Locked layer contains
placeholder marks.
Adjust connectors if necessary to
prevent gaps in connection.
Graphic Removal
To remove the graphic
the frame, locate the fabric
pull tab.Gently pull up on the
tab to remove the fabric.
Step 1
Insert corner A. Turn edge of
graphic so silicon welt is
perpendicular to face of
graphic. Insert narrow side
of welt with fabric to outside
into the channel. Repeat for
other side of this corner.
Step 2
Repeat Step 1 for opposite
corner C, then insert corner
B, followed by corner D, to
complete the installation of
the corners.
Step 3
Once all corners are inserted,
press one silicon edge into
channel from corners and
work toward the center.
Make sure welt is fully inserted
into channel. Continue until
all sides are done. Smooth
out edges of graphic.
It is important to first insert
graphic into each alternate
corner then to the sides of
the frame. If this is not done,
graphic will not fit into the
frame correctly.
Corner A
Corner D
Corner B
Corner C
from
SEG Graphic Installation
Upper Horizontal Extrusion
Lower Horizontal Extrusion
Corner
Connectors Corner
Connectors
Corner
Connectors Corner
Connectors
COMPLETED ASSEMBLY
Slide verticals over
lower connectors.
Then slide upper
connectors into
groove of verticals.
Tighten all knobs.
CEI110 Extrusion
Profile
CEI110 Corner Connection:
1) Loosen knobs, then slide vertical extrusions onto
corner connectors of lower horizontal extrusion.
2) Slide corner connectors of upper horizontal
extrusion into grooves of vertical extrusions.
3) Tighten all knobs to secure connection.
Disassembly:
1) Loosen knobs on vertical extrusions.
2) Slide the vertical extrusions off of
corner connectors on lower and upper
horizontal extrusions.
All knobs must be tightened securely to ensure a proper connection.
CEI110 Assembly & SEG Installation

© 2023
Step 1 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
Item
1
2
3
4
5
6
7
8
9
10
--
Qty.
1
1
1
1
1
1
1
1
1
1
2
Description
39.5”h CEI110 Vertical Extrusion
39.5”h S40 Vertical Extrusion
39.5”h S40 Vertical Extrusion
39.5”h CEI110 Vertical Extrusion
20.906”w Z45 Horizontal Extrusion
20.906”w Z45 Horizontal Extrusion
18”w CEI110 Horizontal Extrusion
18”w CEI110 Horizontal Extrusion
18”w CEI110 Horizontal Extrusion
18”w CEI110 Horizontal Extrusion
Side Light Panel
Steps:
1) Attach vertical [1] to vertical [2]. See CEI110 to S40 Connection detail.
Repeat step, attaching vertical [4] to vertical [3].
2) Connect horizontals [5,6] between verticals [2,3].
3) Attach Door to back of assembly, between verticals [2,3].
See Door Attachment detail.
4) Connect horizontals [7,8] to vertical [1], inserting Light Panel.
Repeat step, connecting horizontals [9,10] to vertical [4],
inserting Light Panel.
FRONT VIEW
FRONT VIEW
TOP VIEW
11
44
5
6
7
8
Door
9
10
2
3
V4
Connector
set
screw
bolt
S40
CEI-110
CEI110 to S40 Connection
*
Slide V4 connector into groove of S40
extrusion as shown; secure with set screw.
Attach CEI-110 extrusion to S40 by
securing bolt to hole of V4 connector.
Light
Panel Light
Panel
Door
Hinge
Hinge
Slide pin into
hinge attached
to vertical.
Slide door
hinge over pin.
Door Attachment
*
Pin
*
*
*
*
**
When assembled
Counter Assembly

© 2023
Step 2 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
When assembled
Item
11
12
13
14
15
16
--
--
Qty.
2
2
2
2
1
1
2
1
Description
38.752”h TSP2 Vertical Extrusion
35.853”h GS310 Veritcal Extrusion
2.955”w Z140 Horizontal Extrusion
2.955”w Z140 Horizontal Extrusion
32”w CEI110 Horizontal Extrusion
32”w CEI110 Horizontal Extrusion
Bracket
Front Light Panel
Steps:
1) Assemble horizontals [13,14] between verticals [11,12] inserting infill;
Attach Brackets to top & bottom of horizontals [13,14] using bolts.
Refer to Corner Assembly detail.
2) Attach corner assembly to horizontals [7,15] & [8,16], inserting Light Panel.
3) Attach corner assembly to horizontals [9,15] & [10,16].
4) Connect transformer to side & front light panels.
Corner Assembly
(Qty. 2)
Bracket
Bracket
bolts
bolts
Infill
11 12
13
14
Light Panel
7
8
9
10
15
16
Corner
Assembly
Corner
Assembly
Bracket
bolts
V4
V4
V4
V4
Attach bracket to
CEI110 horizontals,
using bolts &
V4 Connectors.
Bracket Connection
*
Set
Screw
Bolt
V4 Connector
**
*
*
TOP VIEW
TSP2
GS310
Z140
Bracket
Transformer
144W / 6 Amp / 24V
1) Connect light strips together & attach transformers.
2) Run power cords out hole in back of light panel to power source.
3) Connect light panel to Velcro on back of extrusions.
To Transformer
Light Strip Connector
Cord
Connect light strips
together, as shown.
Light to Light
Attachment
Light to Transformer
Attachment
Light Panel Connection
Counter Assembly (cont’d)

© 2023
Step 3 of 3
Order #XXXXX
Locked layer contains
placeholder marks.
FRONT VIEW
Shelf Pin
1) Slide pin into groove
of Vertical Extrusion.
2) Use hex tool to
tighten pin in place.
Pin
*
Align hole with pin Rotate pin. Spring
will push pin into hole.
Counter Top Attachment
12
*
Pin
Hole
S
E
G
G
r
aphi
c
S
E
G
G
r
aphi
c
Counter Top
Shelf
**
**
S
E
G Graphic
Steps:
1) Apply SEG graphics to assembled base. Refer to the SEG Installation general information page.
2) Place Shelf onto pins. See Shelf Pin detail.
3) Attach Counter Top to assembled base. See Counter Top Attachment detail.
Completed Assembly
Counter Assembly (cont’d)