Seconique NEVADA User manual

IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
PAGE 1
FOR DOMESTIC USE ONLY
NEVADA 5 DRAWER LOW WARDROBE
ASSEMBLY INSTRUCTIONS
SEC/SH/10/19/CA1

PARTS LIST
8x1
12 x2
Large Drawer Back Panel
17 x2
Base
7x1
x1
Drawer Division Panel
14 x10
Large Drawer Front
18
20
x3
x2
Large Drawer Bottom
Door
15 x2
Right Side Panel
19
21
x3
x3
Left Side Panel
Large Division Panel
11
10
9
x1
x1
1x1
2x1
16 x3
3x1
4x1
6x1
5x2
Drawer Bottom Support Bar
Front Baseboard
Small Front Baseboard
Back Baseboard
Top Panel
Small Drawer Back Panel
Small Drawer Front
Small Drawer Bottom
Crossbar
PAGE 2
Please Note:
The below parts have all been stamped with the
part number to help identify them during assembly.
13 x1
Large Back Panel
Drawer Side
(2x)
(3x)
13
12
12
10
6
5
5
4
3
8
7
9
11
1
2
14
14
14
14
15
17
19
16
18
20
21
Small Back Panel
SEC/SH/10/19/CA1

FITTINGS LIST
ABCD
I
Flat Head Screw
Ø6,0 x 10mm (16x)
Double Flat Head Screw
Ø4,0 x 12mm (2x)
Flat Head Screw
Ø4,0 x 14mm (44x)
Flan Head Screw
Ø4,0 x 20mm (12x)
Back Panel Bracket (8x)
E F G
Flat Head Screw
Ø3,5 x 40mm (6x)
Flat Head Screw
Ø4,0 x 50mm (24x) Dowel Ø6,0 x 30mm (75x)
Dowel Ø6,0 x 50mm (2x)
Hanging Rail (1x)
H
Nail 10 x 10 (104x)
J K
Cam Nut Ø12mm (10x) Washer (4x)
L
Plastic Foot (9x)
M
Flan Head Screw
Ø3,5 x 30mm (2x)
N
Cam Bolt (18x)
O
Hole Plugs (30x)
P
Glue (2x)
Glue
Q
Drawer Runners (5x)
R
A1
Back Panel Strip (1x)
S
Strap (2x)
T
Handle (6x)
PAGE 3
USE
DO NOT USE
!
TIPS FOR FITTINGS CAM-LOCKS
PO
P
O
WHEN FITTING CAM NUT. ENSURE STARTING
POSITION IS CORRECT BEFORE YOU INSERT
CONNECTING CAM BOLT TURN CLOCKWISE UNTIL
SECURE
CORRECT WRONG Cam bolt head needs to be in centre
CAMBOLT
Tighten until shoulder in
flush with panel. Do not
overtighten or undertighten
(see example beside)
Shoulder
PanelPanel
U
Cam Nut Ø15mm (8x)
V
Metallic Support (1x)
W X
Hinge (2x)
Y Z
Hinge Plate (2x) Hanging Rail Support (2x)
SEC/SH/10/19/CA1

Pre-Assembly
G+P
H
L
Q
A
Q
A
Detail 5
B
B
Q
Q
PAGE 4
Detail 1 Detail 3Detail 2 Detail 4
Please note
pre-drill
Please note
pre-drill
Please note
pre-drill
Please note
pre-drill
A B
Flat Head Screw
Ø6,0 x 10mm (16x)
Double Flat Head Screw
Ø4,0 x 18mm (2x)
G
Dowel Ø6,0 x 30mm (7x)
H
Nail 10 x 10 (4x)
L
Plastic Foot (4x)
P
Glue
Glue
SECOND HOLE
LAST SIXTH HOLE
Q
180º
Detail 1
Detail 5
Detail 1
Detail 1
Q
Drawer Runners (5x)
Detail 1
Detail 3
Detail 2
Detail 1
Detail 3
Detail 2
Detail 2
Detail 2
Detail 1
Detail 3
Detail 4
Detail 1
Detail 3
Detail 4
Detail 4
Detail 4
1
2
6
6
SEC/SH/10/19/CA1

PAGE 5
G+P CCCCCC
ZXY
H
L
Detail 1 Detail 3 Detail 6 Detail 7 Detail 8
Please note
pre-drill
Please note
pre-drill
Please note
pre-drill
Pre-Assembly
C
Flat Head Screw
Ø4,0 x 14mm (12x)
X
Hinge (2x)
Y Z
Hinge Plate (2x) Hanger Support (2x)
H
Nail 10 x 10 (2x)
L
Plastic Foot (2x)
G
Dowel Ø6,0 x 30mm (2x)
P
Glue
Glue
Detail 1
Detail 3
11
9
2
Detail 7
Detail 7
Detail 8
Detail 8
Detail 6
Detail 6
SEC/SH/10/19/CA1