Seconique LIGHT SONOMA OAK EFFECT CHARISMA Quick start guide

CHARISMA 3 SHELF UNIT
ASSEMBLY INSTRUCTIONS
SEC/SH/04/21/SF1
LIGHT SONOMA OAK EFFECT
Page 01
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY YEARS OF OF SERVICE.
IF YOU FOLLOW THE GUIDELINES FOR ITS SAFE ASSEMBLY AND PERIODIC
MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE THIS PRODUCT.
ITS USE WILL INVALIDATE ANY CLAIM YOU MAY HAVE AND COULD MAKE THIS PRODUCT
UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECIEVES IT MAY BE
NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME TO TIME.
THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK FURNITURE.
DO NOT OVERTIGHTEN FIXINGS.
DO NOT DRAG FURNITURE AS THIS CAN CAUSE DAMAGE TO THE JOINTS.
DO NOT USE FURNITURE POLISH AS THIS WILL SMEAR THE SURFACE.
DO NOT USE LINT OR ABRASIVE CLOTHS AS THESE WILL SCRATCH THE SURFACE.
PLEASE USE A DAMP CLOTH (NOT WET) OR A LINT FREE CLOTH (OR MICROFIBRE TYPE
CLOTH), AND ENSURE THAT YOU TEST THE CLOTH FIRST ON AN INCONSPICUOUS AREA
OF THE FURNITURE BEFORE USE.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS USE A PLACE MAT
UNDER HOT OR COLD ITEMS TO PREVENT MARKING, AND SOFT FELT PADS
UNDERNEATH ORNAMENTS.
IMPORTANT
FOR DOMESTIC USE ONLY
PLEASE READ BEFORE YOU CONTINUE FURTHER

HARDWARE LIST
SEC/SH/04/21/SF1
Page 02
BEFORE YOU START ASSEMBLING.IF YOU DO FIND THAT
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED
PLEASE CONTACT YOUR SUPPLIER IMMEDLATELY.
SOMETHING IS MISSING.DO NOT CONTINUE ASSEMBLY.
1234
567
PARTS LIST
Part Code
Part Number Part Description Quantity Carton
1
2
3
4
5
6
7
S300-306-037-SF1-01 Top Panel 11/1
Middle Panel
Boom Panel
Small Side Panel
Large Side Panel
Small Metal Tube
Large Metal Tube
S300-306-037-SF1-02
S300-306-037-SF1-03
S300-306-037-SF1-04
S300-306-037-SF1-05
S300-306-037-SF1-06
S300-306-037-SF1-07
1
1
1
1
1
1
1/1
1/1
1/1
1/1
1/1
1/1

STEP 1
STEP 2
1 - x1
TOP PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
4 - x1
SMALL SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
F02
SEC/SH/04/21/SF1
Page 03
A03
6 - x1
SMALL METAL TUBE
F
F
4
6
A
A
A
1

B03
STEP 3
STEP 4
2 - x1
MIDDLE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
SEC/SH/04/21/SF1
Page 04
C03
2
Please make sure the panels are aligned correctly.
D03
C
C
D
D
2
B
B
B

TOOLS REQUIRED
HARDWARE REQUIRED
C03
D03
F02
STEP 5
STEP 6
5 - x1
LARGE SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
PARTS REQUIRED
SEC/SH/04/21/SF1
Page 05
7 - x1
LARGE METAL TUBE
Please make sure the panels are aligned correctly.
C
C
D
D
F
F
7
5
3
3 - x1
BOTTOM PANEL