Seconique NEVADA 4 DOOR 2 DRAWER WARDROBE User manual

ASSEMBLY INSTRUCTIONS
PAGE 1 OF 13
CHARLES 4 DOOR 2 DRAWER WARDROBE
SEC/SH/11/16/EU1
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT.ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME.THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE.DO NOT OVERTIGHTEN FIXING.
FOR CLEANING,YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH,DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT.ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
FOR DOMESTIC USE ONLY

NB ( 0.35 )
NC ( 0.5 )
VD ( 0.55 )
NB
NC
VD
PAGE 2 OF 13
SEC/SH/11/16/EU1
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
( SCREWDRIVER NOT PROVIDED )
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
CAM LOCK IS POINTING TOWARD THE HOLE ON EDGE OF PANEL. )
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK.YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 3 OF 13
SEC/SH/11/16/EU1
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING.IF YOU DO FIND THAT SOMETHING IS MISSING,DO NOT CONTINUE
ASSEMBLY,PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
PARTS LIST PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
TOP PANEL
INNER PANEL
BASE PANEL
LOWER BASE CROSSBAR
LEFT SIDE PANEL
BACK CROSSBAR
SHELF PANEL
DOOR WITH MIRROR 1
TOP FRAME
DOOR WITH MIRROR 2
DOOR PANEL 1
1 PC
1 PC
1 PC
1 PC
2 PCS
1 PC
2 PCS
1 PC
4 PCS
1 PC
1 PC
1 PC
1PC
1 PC
MIDDLE SHELF
RIGHT SIDE PANEL
BACK PANEL
15 DOOR PANEL 2 1 PC
16
19
20
17
18
21
DRAWER SIDE - LEFT
2 PCS
2 PCS
2 PCS
2 PCS
2 PCS
2 PCS
DRAWER BOTTOM SUPPORT RAIL
DRAWER BASE
DRAWER FRONT
DRAWER SIDE - RIGHT
DRAWER BACK
1
10 9
9
9
9
2
7
7
11
4
6
8
15
14
13
12
3
5
5
17
19
21
20
16
18

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 4 OF 13
SEC/SH/11/16/EU1
HARDWARE LIST
A
B
C
D
E
F
G
H
I
J
K
L
M
N
52 PCS
20 PCS
42 PCS
8 PCS
6 PCS
24 PCS
2 PCS
4 PCS
3 PCS
4 PCS
12 PCS
4 PCS
4 PCS
DOWEL 6 X 30MM
BOLT M6 X 50MM
SCREW M3.5 X 16MM
SCREW M4 X 30MM
SCREW M4 X 38MM
TACK
DRAWER RUNNER A
DRAWER RUNNER B
HINGES
HANDLE
HANDLE SCREW 4 X 30MM
HANGING RAIL (L & R)
HANGING RAIL SUPPORT
O
PLASTIC H STRIP
12 PCS
SCREW M4 X 50MM
46 PCS
P
Q
R
S
T
U
V
TAPPING SCREW 8 X 12MM
PVC LEG
PVC LEG
ALLEN KEY
ANTI - TIP STRAP
SCREW M4 X 16MM
CAM BOLT + CAM NUT
7 PCS
24 PCS
4 PCS
1 SET
2 PCS
4 PCS
4 SETS
SHELF SUPPORT
SCREW 4 X 25MM
SCREW M3.5 X 12MM
W
4 PCS
X
Y
SCREW M4 X 16MM 2 PCS
1 PC

ABA ( 0.25 )
ABD ( 0.3 )
ABE ( 0.3 )
ACL ( 0.3 )
ABA
ABD
ABE
ACL
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 5 OF 13
SEC/SH/11/16/EU1
STEP 1
Q
H
TOP SECOND HOLE
FIRST HOLE
LAST FOURTH HOLE
8
2
YOU WILL NEED:-
A
M
4 PCS
4 PCS
4
SCREW MUST BE INSERTED IN THE FIRST
HOLE ON THE DRAWER RUNNER
2
6
SAME PANEL
H
Q
A
A
6,2
6,2,8
2
2
LEFT SIDE
RIGHT SIDE
4 PCS
24 PCS
Q
M