Seconique CHARLES 1 DRAWER DRESSING TABLE & MIRROR... User manual

ASSEMBLY INSTRUCTIONS
PAGE 1 OF 9
CHARLES 1 DRAWER DRESSING TABLE & MIRROR FRAME
SEC/SH/11/16/EU1
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT.ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME.THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE.DO NOT OVERTIGHTEN FIXING.
FOR CLEANING,YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH,DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT.ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
FOR DOMESTIC USE ONLY

DR
DT
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 2 OF 9
SEC/SH/11/16/EU1
( SCREWDRIVER NOT PROVIDED )
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF THE
CAM LOCK IS POINTING TOWARD THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK.YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 3 OF 9
SEC/SH/11/16/EU1
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING.IF YOU DO FIND THAT SOMETHING IS MISSING,DO NOT CONTINUE
ASSEMBLY,PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
PARTS PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
SIDE PANEL - LEFT
TOP FRONT CROSSBAR
LOWER FRONT CROSSBAR
BACK PANEL
TOP PANEL
DRAWER BACK
DRAWER SIDE - LEFT
DRAWER SIDE - RIGHT
DRAWER SUPPORT RAIL
BACK MIRROR SUPPORT
DRAWER FRONT
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
SIDE PANEL - RIGHT
DRAWER BASE
14 MIRROR 1 PC
1
5
14
6
13
13
4
3
2
10
7
8
9
11
12

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 4 OF 9
SEC/SH/11/16/EU1
HARDWARE LIST
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
DOWEL 6 X 30MM
SCREW 4 X 30MM
SCREW 4 X 38MM
TACK
HANDLE
HANDLE SCREW 4 X 30MM
L-BRACKET
EDGE PROTECTOR
SCREW 3.5 X 16MM
DRAWER RUNNER A
DRAWER RUNNER B
ALLEN KEY
CAM BOLT + CAM NUT
SHELF SUPPORT
SCREW 4 X 50MM
BOLT M7 X 60MM
20 PCS
11 PCS
4 PCS
7 PCS
1 PC
2 PCS
3 PCS
2 SETS
30 PCS
2 PCS
2 PCS
1 PC
2 SETS
8 PCS
2 PCS
8 PCS
Q
R
ANTI - TIP STRAP
SCREW M4 X 16MM
2 PCS
2 PCS

CY ( 0.3 )
DA ( 0.15 )
DB ( 0.18 )
DC ( 0.18 )
DD ( 0.15 )
DE ( 0.28 )
CY
DA
DB
DC
DD
DE
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 5 OF 9
SEC/SH/11/16/EU1
STEP 1 STEP 2.1
STEP 2.2
YOU WILL NEED:- YOU WILL NEED:-
B
M
SCREW MUST BE INSERTED
IN THE FIRST HOLE ON THE
DRAWER RUNNER.
A
H
I
J
K
14 PCS
3 PCS
2 SETS
18 PCS
2 PCS
8 PCS
1 PC
A
JH
I
J
KJ
B
M
4
2
3
6
5
1
1
3
2
4
5
5
3
2
1
4
A
FRONT BACK
FIRST HOLE
LAST SECOND HOLE
UP SECOND HOLE

DF ( 0.2 )
DL ( 0.12 )
DF
DG
DL
DM
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 6 OF 9
SEC/SH/11/16/EU1
YOU WILL NEED:- YOU WILL NEED:-
C 3 PCS J 6 PCS
STEP 3 STEP 4
C
J
5
3
2
4
1
6
6
2
1 & 5
6
2
BEFORE FIXING THE TOP PANEL.
PLEASE ALIGN THE TOP PANEL
WITH THE FRONT FRAME.
FRONT SIDE VIEW
A
6

BP ( 1 : 7.5 )
BR ( 1 : 6 )
BT ( 1 : 3.5 )
BU ( 0.2 )
BV ( 1 : 5 )
CU ( 0.22 )
CV ( 0.2 )
DJ ( 0.35 )
DU ( 0.1 )
DY ( 0.17 )
EA ( 0.2 )
EB ( 0.15 )
BP
BR
BT
BU
BV
CU
CV
DH
DJ
DU
DV
DW
DY
EA
EB
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 7 OF 9
SEC/SH/11/16/EU1
STEP 5.2
STEP 6
STEP 5.5
STEP 5.1
STEP 5.3
STEP 5.4
STEP 5.6
YOU WILL NEED:-
6 PCS
2 PCS
4 PCS
7 PCS
1 PC
2 PCS
2 PCS
A
E
F
L
G
J6 PCS
YOU WILL NEED:-
N2 SETS
C
D
D
A
G
LN
C
E
A
P2 PCS
O8 PCS
O
P
14
1 X DRAWER
THIRD HOLE
LAST THIRD HOLE
BACK
FRONT
A
C
A
F
L
L
L
J
N
N
D
7
9
810
10
11
11
10
12
12
8&9
8&9
7
10
12

DK ( 0.18 )
DK
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 8 OF 9
SEC/SH/11/16/EU1
STEP 7 STEP 8
YOU WILL NEED:-
C6 PCS
C
13
13
13

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 9 OF 9
SEC/SH/11/16/EU1
WARNING
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
HARDWARE LIST
( Q ) Anti-Tip Strap - 2 pcs
( R ) M4 X 16MM - 2 pcs
TOP
WALL
TOP
WALL
TOP
Q
Q
R

ASSEMBLY INSTRUCTIONS
PAGE 1 OF 3
CHARLES 1 DRAWER DRESSING TABLE STOOL
SEC/SH/11/16/EU1
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT.ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME.THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE.DO NOT OVERTIGHTEN FIXING.
FOR CLEANING,YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH,DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT.ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
FOR DOMESTIC USE ONLY

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 2 OF 3
SEC/SH/11/16/EU1
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING.IF YOU DO FIND THAT SOMETHING IS MISSING,DO NOT CONTINUE
ASSEMBLY,PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
PARTS LIST PARTS LIST
1
2
3
4
TOP CROSSBARS
CENTRE CROSSBAR
SIDE PANEL
SEAT CUSHION
2 PCS
1 PC
2 PCS
1 PC
HARDWARE LIST
A
B
C
D
E
DOWEL 6 X 30MM
BOLT 6 X 50MM
SCREW M3.5 X 16MM
EDGE PROTECTOR
ALLEN KEY
12 PCS
6 PCS
12 PCS
4 PCS
1 PC
1
1
2
3
3
4

LP ( 0.2 )
LU ( 0.26 )
LV ( 0.3 )
LP
LR
LU
LV
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE.
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 3 OF 3
SEC/SH/11/16/EU1
STEP 1.1 STEP 2.1
STEP 1.2
STEP 2.2
STEP 2.3
YOU WILL NEED:- YOU WILL NEED:-
A
B
E
12 PCS
6 PCS
1 PC
D 4 PCS
C 12 PCS
1
12
3
1
2
1
3
4
1
4
A
E
B
C
DC