Seconique Corona 2 Door 1 Drawer Wardrobe User manual

DO NOT
USE
OLIVER 2 DOOR WARDROBE
ASSEMBLY INSTRUCTIONS
Page 01
IMPORTANT
FOR DOMESTIC USE ONLY
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT. ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME. THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE. DO NOT OVERTIGHTEN FIXING.
FOR CLEANING, YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH, DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT. ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
SEC/SH/09/23/EU1

PART LIST
Page 02
Part Number Part Code Part Description Quantity Carton
1 S100-101-205-EU1-01 11/2
2
3
Back Panel II
4
Side Panel - Left
1
51
6
7
8
Shelf Panel
2
S100-101-205-EU1-02
S100-101-205-EU1-03
S100-101-205-EU1-04
S100-101-205-EU1-05
S100-101-205-EU1-06
S100-101-205-EU1-07
S100-101-205-EU1-08
2
2
1
1
Top Panel
Side Panel - Right
Doors
2/2
Bottom Panel
Back Panel I
1
2
3
4
5
6
6
7
7
8
8
SEC/SH/09/23/EU1
1/2
1/2
1/2
2/2
2/2
2/2

PLASTIC H STRIP
ANTI - TIP STRAP
SCREW M4 X 16MM
PVC STOPPER
HINGES 7/8
HARDWARE LIST
(SCREWDRIVER NOT PROVIDED)
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
THE CAM LOCK IS POINTING TOWARD ON THE EDGE OF THE PANEL.)
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK. YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.
Page 03
A
B
C
D
E
F
G
H
I
DOWEL 6 X 30MM 12 PCS
2 PCS
SCREW M4 X 32MM
CAM BOLT + CAM NUT
HANDLE
SCREW M3.5 X 16MM 14 PCS
TACK 46 PCS
J
K
L
M
SCREW M3.5 X 12MM
HANDLE SCREW 20MM
L PVC FOOT
ALLEN KEY
10 PCS
4 SETS
4 PCS
SCREW M6 X 50MM
1 PC
12 PCS
N
TAPPING SCREW M8 X 12MM
HANGING RAIL SUPPORT
HANGING RAIL
O
P
Q
R
S
2 PCS
2 PCS
1 PC
3 PCS
2 PCS
2 PCS
8 PCS
4 PCS
T
SQUARE PVC FOOT 2 PCS
6 PCS
2 PCS
SEC/SH/09/23/EU1

STEP 1
STEP 2
Page 04
PARTS REQUIRED
1 - SIDE PANEL - LEFT x1
HARDWARE REQUIRED
TOOLS REQUIRED
K04
A08
O02
DP
B04
PARTS REQUIRED
3 - SHELF PANEL x1
HARDWARE REQUIRED
TOOLS REQUIRED
A04
B04
A
KO
B
K
B
A
1
2
KK
O
B
B
B
A
A
A
A
A
A
2 - SIDE PANEL - RIGHT x1
4 - BOTTOM PANEL x1
5 - TOP PANEL x1
D02
P02
3
4
5
A
A
A
B
B
B
SEC/SH/09/23/EU1

STEP 3
STEP 4
Page 05
PARTS REQUIRED
1 - SIDE PANEL - LEFT x1
2 - SIDE PANEL - RIGHT x1
3 - SHELF PANEL x1
HARDWARE REQUIRED
TOOLS REQUIRED
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
C04
4 - BOTTOM PANEL x1
B
3
1
2
4
C
C
C
C
SEC/SH/09/23/EU1

STEP 5
STEP 6
Page 06
PARTS REQUIRED
5 - TOP PANEL x1
HARDWARE REQUIRED
TOOLS REQUIRED
F10
C04
L02
F
L
E
E
M02
R
E
MF
F
C
C
C
FF
FF
F
M
L
5
E
E
E
E
EE
E
E
7
7
6
6
PARTS REQUIRED
HARDWARE REQUIRED
TOOLS REQUIRED
6 - BACK PANEL I x2
46
E
R03
7 - BACK PANEL II x2
C
SEC/SH/09/23/EU1

STEP 7
STEP 8
Page 07
PARTS REQUIRED
x2
HARDWARE REQUIRED
H12
TOOLS REQUIRED
G02
PARTS REQUIRED
J04
Q01
D
N
D
N
NN
NN
DD
DD
DD
DD
DD
3. FRONT-TO-BACK BY THE SLACKING
THE HINGE ARM MOUNTING SCREW
YOU SHOULD RE-ADJUST SCREWS
AS SHOWN TO ALIGN DOOR ONCE
HINGES HAVE BEEN ATTACHED.
1. VERTICAL ADJUSTMENT VIA
SLOT IN THE MOUNTING PLATE
2. LATERAL ADJUSTMENT BY
SCREW ADJUSTING
H
N
8
8
HARDWARE REQUIRED
D12
TOOLS REQUIRED
N06
8 - DOORS x2
8 - DOORS
8
8
Q
H
H
N
J
G
H
H
H
H
G
J
J
SEC/SH/09/23/EU1

STEP 9
Page 08
WARNING
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
T
TOP
TOP
WALL
S
WALL
TOP
S
PART REQUIRED
T
02
HARDWARE REQUIRED
S
02
TOOLS REQUIRED
SEC/SH/09/23/EU1