Seconique NEVADA User manual

DO NOT USE
!
NEVADA 5 DRAWER NARROW CHEST
ASSEMBLY INSTRUCTIONS
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
CARE AND MAINTENANCE
FOR DOMESTIC USE ONLY
SEC/AY/06/21/CA6
PAGE 01

Part Number Part Description Quantity Carton
01
02
03
04
05
06
07
08
09
10
Le Side Panel 11/1
1
2
1
1
2
10
5
5
5
Right Side Panel
Back Baseboard
Front Baseboard
Top Panel
Back Panel
Drawer Side
Drawer Back Panel
Drawer Front
Drawer Bottom
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
1/1
TOOLS REQUIRED
1
2
3
3
4
9
10
87
7
5
6
6
PARTS LIST
Please Note:
The below parts have all been stamped with the part number to help identify them during assembly.
SEC/AY/06/21/CA6
PAGE 02

FITTINGS LIST
A B C D
E F G H
I J K L
M
Cam Bolt (14x)
Flat Head Screw
Ø6,0 x 10mm (20x)
Flat Head Screw
Ø4,0 x 14mm (30x)
Flan Head Screw
Ø4,0 x 20mm (10x)
Flat Head Screw
Ø4,0 x 50mm (16x)
Dowel Ø6,0 x 30mm (56x) Nail 10 x 10 (74x) Cam Nut Ø12mm (10x)
Plastic Foot (4x)
Hole Plugs (6x) Glue (2x) Drawer Runners (5x)
N
Cam Nut Ø15mm (4x)
Flan Head Screw
Ø3,5 x 30mm (1x)
Washer (2x)
O P
Back Panel Strip (1x)
Q R
Strap (1x) Handle (5x)
SEC/AY/06/21/CA6
PAGE 03
2/+ 2/+ 2/+ 2/+
2/+ 2/+ 2/+
2/+
2/+
1/+
1/+
1/+
1/+
TIPS FOR FITTINGS CAM-LOCKS
Cam bolt head needs to be in centre
PO
WHEN FITTING CAM NUT. ENSURE STARTING
POSITION IS CORRECT BEFORE YOU INSERT
CONNECTING CAM BOLT TURN CLOCKWISE UNTIL
SECURE
CORRECT WRONG
CAMBOLT
Tighten until shoulder in
flush with panel. Do not
overtighten or undertighten
(see example beside) Shoulder
Panel
P
Panel
O
S
Hole Plugs (10x)
2/+

1
Detail 1
Detail 4
Detail 4
Detail 1
2
1 - x1
LEFT SIDE PANEL
STEP 1
PARTS REQUIRED
SEC/AY/06/21/CA6
PAGE 04
TOOLS REQUIRED
HARDWARE REQUIRED
E02
J02
F02
10 x 10
N01
STEP 2
2 - x1
RIGHT SIDE PANEL
PARTS REQUIRED
TOOLS REQUIRED
HARDWARE REQUIRED
E02
J02
F02
10 x 10
N01
F
J
E+N
Detail 1 Detail 4
F
J
E+N
Detail 1 Detail 4
Ø6,0 x 30mm
Ø6,0 x 30mm

Detail 5
Detail 3
2
UP SECOND HOLE
SECOND HOLE
LAST FIFTH HOLE
UP SECOND HOLE
SECOND HOLE
LAST FIFTH HOLE
HARDWARE REQUIRED
PARTS REQUIRED
1 - x1
LEFT SIDE PANEL
TOOLS REQUIRED
STEP 4
STEP 3 SEC/AY/06/21/CA6
PAGE 05
A10
B05
O05
LEFT
PARTS REQUIRED
2 - x1
RIGHT SIDE PANEL
HARDWARE REQUIRED
TOOLS REQUIRED
A10
B05
O05
RIGHT
PLEASE NOTE
PRE-DRILLED
HOLES.
PLEASE NOTE
PRE-DRILLED
HOLES.
PLEASE NOTE
PRE-DRILLED
HOLES.
PLEASE NOTE
PRE-DRILLED
HOLES.
Detail 5
O
A
B
Detail 3
O
A
B
1
Ø6,0 x 10mm
Ø4,0 x 14mm
Ø4,0 x 14mm
Ø6,0 x 10mm