SECTORMAXX WK-2 User manual

QUICK START GUIDE
WK-2x Access Point
WK-2, WK-2-B, WK-2-C / 802.11ac Dual Band Access
Version 1.1

2 3
Package Contents 3
WK-2 Mounting Options 4
WK-2-C Mounting 14
Powering Up the Access Point 22
Conguring the Access Point 25
Step 1: Login 25
Step 2: Radio 30
Step 3: Security Proles 34
Step 4: Conguration 36
Guest Network 38
Contents
Contents depend on your WK-2x model. Please refer to the installation manual of your product.
WK-2x
• 802.11ac Dual Band Access Point
• Built in 3x3 internal antennas
• Powered by POE+
• 2 LAN ports for Network Extensions
System Requirements
Windows or Mac PC with an Ethernet interface.
WK-2x Default Settings
Package Contents
Operation Mode: Access Point
IP Address: DHCP or 192.168.1.250
Username/Password: pakedge/pakedgea
SSID: Pakedge2.4-1 and Pakedge5-1
Power Output: High
Security: Disabled

45
WK-2 Mounting Options Vertical mount: Secure the wall bracket to the wall anchors using the included hardware.
UP
A1 A2
A4A3
A6 A8A7
A5
B4 B3
B2
B1
A. Double-gang electrical box, wall
B. Single-gang electrical box, european
outlet box us 4” round junction box, us
3.5” round juction box
Using the Provided Wall Mount Bracket.

67
Line the two tabs on the top of the wall bracket with the two pockets on the back of the access
point.
UP
Horizontal mount: Line up the slots and secure the wall bracket to the wall anchors using the
included hardware.
Attach the recommended plastic cable clip. Route cables along the channel on the back of the
WAP and secure cables to the plastic clip by pressing the cable to the clip.
ROUTE CABLES
RECOMMENDED
CABLE CLIP PLACEMENT

8 9
Place the WAP rmly against the wall bracket, ensuring the cables are tucked in the channel on the
back of the WAP and/or behind the wall bracket.

10 11
Slide the WAP downward until the top two tabs on the Wall Bracket are locked into place
SLIDE WAP DOWN
TO LOCK
Secure the WAP to the wall bracket’s bottom tab with the included security screw.
SUPPLIED TORX SCREWDRIVER(OPTIONAL)
TORX SECURITY SCREW
TORX SECURITY SCREW INSTALLATION

12 13
Using provided T-bar Bracket
Place the appropriate sized T-bar bracket into the slots on the back of the WAP and line up the
two holes on the T-bar bracket with the two mounting points on the back of the WAP. Using the
supplied hardware, mount the T-bar bracket to the WAP.
NOTE: Please refer to the user manual for more detailed information regarding the installation and
conguration of the access point.
Rotate the WAP counter-clockwise until the T-bar bracket is secured to the T-bar.

14 15
1. Open the release latch and push on the back of WK-2-C to swing the WAP out from
ceiling/wall bracket.
WK-2-C Mounting 2. Swing WAP down.

16 17
3. Using the supplied template, cut a 9.125” diame-
ter circle at the desired mounting location for your
WK-2-C. Route an in-wall Ethernet cable through
the opening on the back of WK-2-C housing.
Insert the WK-2-C into the ceiling/wall.
4. Use a Phillips screwdriver to tighten the mounting ears. Use a clockwise rotation.
NOTE: Do not use excessive force when tightening the mounting-ears. This can strip the mounting
ears and render them non-functional.

18 19
5. Plug Ethernet cable into WK-2-C. Route Ethernet cable as shown. Use optional cable clip if
necessary.
6. Swing WAP back into WK-2-C housing.

20 21
WK-2-C installation with optional pre-construction bracket
Pre-construction bracket sold separately.
1. Place the pre-construction bracket against the bottom of the ceiling studs at the desired
mounting location.
2. Mark locations for mounting screws. Drill 1/16” pilot holes at marked locations. Secure
pre-construction bracket to ceiling studs using the provided hardware.
3. Install sheet rock over pre-construction bracket. Make note of where the cutout on the
pre-construction bracket is when installing the drywall.
4. Cut opening in sheet rock using the cutout on the pre-construction bracket as a guide.
Note: the Pakedge logo should be facing outwards.

22 23
The access point can be powered via PoE+ or by the included power adapter. Please see below for
examples:
Power Using a PoE+ Injector
Powering Up the Access Point
WK-2
Smartphone
Panel
Laptop
Laptop
Tablet
Switch
PoE+
Injector
Ethernet Cable
Ethernet Cable
WK-2
Smartphone
Panel
Laptop
Laptop
Tablet
Switch
Ethernet Cable
Power using a PoE+ Switch

24 25
Power using the included power adapter
The Wireless Access Point should now be up and running with its default settings. It does not need
to be congured to be functional. To make changes to the SSID and security settings, you need to
access the WK-2x using a web browser.
WK-2
Smartphone
Panel
Laptop
Laptop
Tablet
Power
Outlet
AC Adapter
Step 1: Login
There are two options to login to the unit:
Option 1:
Connect a computer to the WK-2x with an Ethernet cable. Enter 192.168.1.250 into the address
bar of your web browser. You should see a login page. In the username box, type pakedge. In the
password box, type pakedgea and click Login.
NOTE: If your computer is not set to the default IP scheme of the WK-2x (192.168.1.X), you must
rst congure the TCP/IP settings on your computer to log in to the WK-2x through a web brows-
er.
Conguring the Access Point

26 27
Using Windows 7
1. Under Control Panel – Network and
Internet, click on View Network Status and
Tasks.
2. On the left panel, click on Change Adapter
Settings and right-click on Local Area
Connection.
3. Select Properties.
4. Select Internet Protocol Version 4
(TCP/IPv4) and click Properties.
5. Select Use The Following IP Address and
enter the following information:
Additional settings can be left blank.
6. Click “OK” and “Close”
IP Address: 192.168.1.10
Subnet Mask: 255.255.255.0
Following page will display when logged in:

28 29
Option 2
You can use the Where’s My WAP (WMW)
software, which is free to download from
the Dealer Portal section of the Pakedge
website
This application will automatically scan the
network for any Pakedge access point. Once
the application nds the access points,
you will have the option to change their IP
addresses by clicking on the pencil icon.
Note: If you plan on using multiple access points at your home, remember that they all come with
the same IP address by default.
Once you are logged in to the AP, hover over Network and click on LAN.
Note: The default IP Setting on the WK-2x is DHCP. If you want to assign a static IP to the WK-2x,
select Static IP from drop-down menu and ll in the IP address, subnet mask and gateway infor-
mation. Click Apply to implement your changes.

30 31
The rst tab under Wireless is Radio. By default, the WK-2x operates in Access Point Mode. The
mode can be set for either the 2.4 or the 5 GHz band. The available modes for the WK-2x are:
Access Point, WDS Root Access Point, WDS Repeater and WDS Bridge.
Step 2: Radio
NOTE: That once you apply a country code, you cannot change it unless you reset the WK-2x to
factory default.
WK-2
In Access Point Mode, the WK-2x broadcasts both 2.4 GHz and 5 GHz signals to stations that
support 802.11 ac.
Access Point Mode
Smartphone
Panel
Laptop
Laptop
Tablet
Ethernet Cable

32 33
In WDS Bridge Mode, you can connect the WK-2x to a client by its Ethernet port. The WK-2x will
receive the wireless signal from an access point and send the signal, through its Ethernet port, to
the client. A separate WK-2x must be in WDS Root Access Point mode for this setting to operate.
WDS Bridge Mode
WK-2
WK-2
Laptop
Ethernet Cable
Ethernet Cable
WDS Repeater Mode can be used to connect two WK-2x access points wirelessly and extend your
wireless network coverage. A separate WK-2x must be in WDS Root Access Point mode for this
setting to operate.
WDS Repeater Mode
Refer to the user manual for information on the other operating modes.
WK-2
WK-2
Laptop
Ethernet Cable

34 35
The next tab over is the Security Proles. You can change security settings for 2.4 GHz and 5 GHz.
Step 3: Security Proles The most secure and common mode is WPA2-PSK.
This setting is known to be the most secure and is compatible with all the latest devices.
NOTE: When choosing the security settings, consider your client devices. Older laptops or phones
do not support WPA2 security. Also, some devices are only compatible with certain security types.
You may want to reference your device specications.

36 37
In this section, you can change the SSID name and apply the security prole that was set up in step
4. By default, the SSID is Pakedge2.4-1 and Pakedge5-1. You will have the option to change the
name and add security proles by selecting the options from the drop-down menu.
Step 4: Conguration

38
This will allow you to set up a guest network. Please see manual for further details.
Guest Network
pakedgedevice&software inc
3847 Breakwater Avenue, Hayward,CA 94545-3606
Main: 650-385-8700 Fax: [phone]
www.pakedge.com
[e-mail]