TRENDnet TEW-825DAP(V1) User manual

TEW-825DAP(V1)
Quick Installation Guide

Table of Content
1 English
1. Before You Start
2. Initial Access Point Setup
3. AP Management Utility
4. Mounting the Device

1
1. Before You Start
Package Contents
ŸTEW-825DAP
Ÿ1 x Network cable (1.5m / 5 ft.)
ŸCD-ROM (User's Guide and Configuration Utility)
ŸQuick Installation Guide
ŸPower adapter (12V DC, 1.5 A)
ŸMounting plate
Minimum Requirements
ŸComputer with network port and web browser
ŸNetwork switch or router with an available network port

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
2
2. Initial Access Point Setup
1. Bring the TEW-825DAP to a location of its final installation point.
2. Connect the TEW-825DAP to your router or switch. You may also connect the device directly to
a network port on your computer. If you are connecting to a router or switch, make sure your
computer is connected to the same network.
3. If you are connecting your TEW-825DAP to a PoE router or switch, the device will power on
automatically. If you are connecting to a computer, or a non-PoE router or switch, you will need
to use the included power adapter.
4. To use the power adapter, plug the power adapter into the TEW-825DAP, then plug the adapter
into an electrical outlet. Wait 60 seconds, then confirm that the status LEDs on the front of the
unit are illuminated. Your TEW-825DAP access point is now active. The device is pre-
configured to automatically connect to your network.
5. For your security, each TEW-825DAP comes pre-encrypted with a unique WiFi Name (SSID) and
WiFi Password. You can find your device's SSID and WiFi password on the white labels located
on the device. Use this information to connect to the TEW-825DAP access point. If the
TEW-825DAP is reset, the SSID and WiFi key will also be reset to the default login credentials
located on the white label.
6. No further setup is required, proceed to Section 4 Mounting the Device. To change device
settings proceed to Section 3 AP Management Utility.
Preset
Wireless Settings
Wi-Fi Name/SSID
(AC/N)
TRENDnetXXX_5GHz_XXXX
(N/B/G)
TRENDnetXXX_2.4GHz_XXXX
Wi-Fi Password
Management Login
http://tew-825dap
username: admin
password: admin
XXXXXXXXXXXXX

3
1. Insert the included CD into your computer, and select AP Utility from the menu.
Note: The AP Management Utilitly only supports Windows based computers. Please visit
TRENDnet.com for complete list of the supported operating systems.
Mac Users: Please refer to the User's Guide to manually configure the access point.
3. AP Management Utility
2 . Run the utility. The utility will attempt to detect your device automatically. If it does not, click
on the Discover button.
AP Utilily

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
4
4. The Device Settings page will show your basic Wi-Fi network settings. If your network requires
a static IP address, select the Static radio button and enter your settings. If you are not sure,
leave IP Mode on the default setting, DHCP.
3. Select your device by checking the box next to your TEW-825DAP, and click on Device
Settings.
IP Address 192.168.10.25
Static

5
5. To configure your wireless network, select the Band from the dropdown menu, and enter your
settings. If you are using both 2.4GHz and 5GHz networks, they must be configured
individually. The Key is your current WiFi password. The default key is located on the white
sticker on the bottom of the TEW-825DAP.
6. When you are finished, enter the AP management password for your TEW-825DAP (default:
admin) and click OK to save your changes. If this is the first time you are accessing the device,
or if the unit has been reset, the default password is admin. The utility will save your settings.
7. If you are using both 2.4GHz and 5GHz networks, they must be configured individually. Repeat
steps 2 to 6 to configure your other network.
8. Once your wireless networks are configured, confirm connectivity by logging into your
TEW- 825DAP WiFi network. If you can successfully connect, your configuration is complete.
Band
Preset
Wireless Settings
Wi-Fi Name/SSID
(AC/N)
TRENDnetXXX_5GHz_XXXX
(N/B/G)
TRENDnetXXX_2.4GHz_XXXX
Wi-Fi Password
Management Login
http://tew-825dap
username: admin
password: admin
XXXXXXXXXXXXX

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
6
9. To access the unit's advanced settings, launch the AP Management utility, locate your
TEW-825DAP, click on the IP Address, and select Yes to configure your device.
10. This will launch your default web browser, and automatically direct it to your TEW-825DAP for
advanced settings.
11. On the Login screen, enter the username and password. If this is your first time accessing the
device, or if the TEW-825DAP has been reset, the default login credentials are:
User Name: admin
Password: admin
12. Select the desired language, then click Login to continue.
192.168.10.62

7
13. The status screen will display information about your TEW-825DAP access point, and the
unit's wireless networks.
14. For detailed information on advanced settings and features, please refer to the User's Guide.

ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
8
1. Remove the mounting plate from the TEW-825DAP.
4. Mounting the Device
2. Place the mounting plate on the wall or ceiling where the device will be located, and mark the
location of the screw holes. Ensure that the device has enough clearance to slide on and off the
mounting plate. If it is a non-PoE installation, ensure that your mounting location has access to
an electrical outlet.
3. Drill out the marked screw holes, and insert the plastic wall anchors into the screw holes.
4. Secure the mounting plate, using the screws that came with the device.
5. Place the TEW-825DAP on the mounting plate, and attach the network cable. If it is a non-PoE
installation, connect the power adapter.
Toll Free English Technical Support
US/Canada: 855-373-4741
Hours: Monday-Friday
7:00 AM- 6:00 PM, Pacific Standard Time.
After hours: 866-845-3673
25
4
3