Security Brands RIDGE RTE 14-RTE433T User manual

1 of 4
Model 14-RTE433T
QUICK START GUIDE
2Make sure you have all items shown here. (Screwdriver not shown)
START HERE
1Carefully unpack box.
RTE Unit 9-V Battery Lock Key Carriage Bolt
( x4 )
Hex Nut
( x4 )
Hole PlugKey Switch Keys
Key Switch
For enabling and
disabling unit
(Unit is disabled as
shown)
Exit Button
Triggers gate/door
to open
Lock
For securing interior
of RTE unit
RTE Unit Front Panel (Front) RTE Unit Front Panel (Back)
Internal wiring not shown for clarity.
Programming Button
For pairing transceiver
with RTE unit
Reset Button
For pairing RTE unit
with transceiver Power LED
Indicates whether or
not unit has power
Relay Status LED
Indicates whether relay is
active or inactive
(Relay is active when lit)
Connection Terminals
For wiring to compatible
AC/DC power source and
gate operator or door opener
Programming LED
Indicates status of
pairing process
9-V Battery
Must be installed
before use
What’s what?
Important components labeled
You MUST have the Ridge Transceiver (14-REC20) for this RTE unit to work. It is bundled
with the Ridge 2.0 (14-500), Ridge RTE (14-RTE433), and can be purchased separately as well.
Transceiver (Not Included)
Shown with cover removed.
Internal wiring not shown for clarity.
Adhesive
Mounting Pad

© 2021 Security Brands, Inc. All rights reserved. QSG-14RTE433T-EN Rev. A (1/2021)
2 of 4
Model 14-RTE433T
QUICK START GUIDE
CAUTION!

The transceiver is not weatherproof and must be mounted inside a
weatherproof enclosure. Internal components can be damaged if
exposed to the elements.
Failure to comply will VOID WARRANTY.
5a Connect transceiver
Ridge Transceiver
12–24 VAC/DC
POWER
RELAY A
12–24 VAC/DC
POWER
Gate Operator / Door Opener
POS. (+)
NEG. (–)
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
OR
12–24-VAC/DC
Power Source
(Not Included)
NC
NEG. (–)
POS. (+)
+–
COM
NO
FREE EXIT
COM
5b Connect transceiver
COM
RADIO
Ridge Transceiver
12–24 VAC/DC
POWER
RELAY A
12–24 VAC/DC
POWER
Gate Operator / Door Opener
POS. (+)
NEG. (–)
COM
REVERSE LOOP
COM
OPEN
STOP
CLOSE
12–24-VAC/DC
Power Source
(Not Included)
NC
NEG. (–)
POS. (+)
COM
NO
FREE EXIT
COM COM
RADIO
Gate Operator Timer-to-Close
OFF
Gate Operator Timer-to-Close
ON
A closing gate can cause injury to
persons or damage to property.
ALWAYS USE SAFETY DEVICES!
CAUTION!

WARNING!
AUTOMATIC GATES CAN CAUSE SERIOUS INJURY OR DEATH!
ALWAYS CHECK that the GATE PATH IS CLEAR BEFORE OPERATING!
REVERSING or other SAFETY DEVICES SHOULD ALWAYS BE USED!

3Unlock and remove front panel of
RTE unit; then using included
carriage bolts and hex nuts, attach
unit to pedestal as shown.
Consult gate operator or
door opener manual for
exact connections.
Terminals vary widely across
manufacturers and models.
Consult gate operator or
door opener manual for
exact connections.
Terminals vary widely across
manufacturers and models.
+–
4Using Tek screws, zip ties, or
included adhesive mounting pad,
attach transceiver to inside wall or
another surface of gate operator.

QUICK START GUIDE 3 of 4
Model 14-RTE433T
6b Remove RTE unit front panel; then hold
down Reset button on circuit board for
5 seconds and let go.
(Make sure battery is connected)
6c While pairing, RTE unit will beep momentarily.
Once transceiver LED goes out, pairing is complete.
LED will
go out
LED will light
solid orange
6a Remove transceiver cover; then
hold down Programming button on
circuit board for 3 seconds and let go.
Your system is ready to use.
INSTALLATION COMPLETE!
N
7Make sure gate/door path is clear;
then press exit button on RTE unit
and confirm gate/door opens.
(If nothing happens, repeat Step 6)
Unit Enabled
(exit button active)
Unit Disabled
(exit button inactive)
AThe RTE unit can be disabled and re-enabled at any time by taking the
key switch keys and using the key switch located below the exit button. BUnit Reset Procedure
This procedure is used to reset unit to factory default settings.
Step 1 - Remove front panel of RTE unit.
Step 2 - Disconnect battery.
Step 3 - Press and hold Reset Button; reconnect battery; then release Reset Button.
Unit will sound one (1) tone. Release Reset Button after you hear tone.
Step 4 - Press and release Reset Button; then reattach front panel onto RTE unit.
The unit is now reset to factory default settings.

© 2021 Security Brands, Inc. All rights reserved. QSG-14RTE433T-EN Rev. A (1/2021)
QUICK START GUIDE 4 of 4
Model 14-RTE433T
Notes
Ridge RTE
14-RTE433T
NEED HELP Call [phone]
Email [email protected]
We are available Mon–Fri / 8am–5pm Central