Secutron MR-3500 Series User manual

Installation and Operation Manual LT-1083SEC Rev. 2.1
September 2018
MR-3500
Fire Alarm Control Panel

1
Table of Contents
1.0 Industry Canada and FCC Notice 5
1.1 Notice for all MR-3500 Series Built-In UDACTs Sold in Canada ................................... 5
1.2 Industry Canada Notice ................................................................................................. 5
1.3 Notice for all MR-3500 Series Built-in UDACTs Sold in the U.S.A. ............................... 5
1.4 FCC Notice .................................................................................................................... 6
2.0 Introduction 7
2.1 The MR-3500 Addressable Fire Alarm Control Panel .................................................... 7
2.2 General Notes ................................................................................................................ 8
3.0 MR-3500 Overview 9
3.1 MR-3500 Fire Alarm Control Panel Models ................................................................... 9
3.2 MR-3500 System Components ...................................................................................... 10
4.0 Installation 18
4.1 BBX-1024DS and BBX-1024DSR Mechanical Installation ............................................ 18
4.2 Installation Tips .............................................................................................................. 19
4.3 Installing Adder Modules ................................................................................................ 19
4.4 Installing the ALC-636 Dual Loop Adder ........................................................................ 23
5.0 Operation 26
5.1 Addressable/Analog Devices ......................................................................................... 26
5.2 Configurable Input Types ............................................................................................... 28
5.3 Output Types ................................................................................................................. 33
5.4 NAC Circuit Operation ................................................................................................... 34
5.5 Single Stage Operation .................................................................................................. 35
5.6 Two-Stage Operation ..................................................................................................... 36
5.7 Evacuation Codes .......................................................................................................... 37
5.8 Positive Alarm Sequence ............................................................................................... 37
5.9 Remote Annunciator Operation ..................................................................................... 39
5.10 Dialer Operation ............................................................................................................. 41
5.11 Using the Operation Menu from the Control Panel ........................................................ 42
6.0 Indication & Controls 55
6.1 Indication and Controls .................................................................................................. 55

2
Table of Contents
6.2 LCD Display ................................................................................................................... 55
6.3 Common LED Indicators and Control Buttons ............................................................... 57
7.0 Wiring 61
7.1 Wiring Tables ................................................................................................................. 61
7.2 Wire Routing .................................................................................................................. 63
7.3 Addressable Loop Wiring ............................................................................................... 64
7.4 NAC Circuit Wiring ......................................................................................................... 65
7.5 Module and Devices Wiring ........................................................................................... 68
7.6 Power Supply Wiring ...................................................................................................... 72
7.7 System Checkout ........................................................................................................... 75
7.8 Troubleshooting .............................................................................................................75
8.0 Appendix A - Compatible Receivers 76
9.0 Appendix B - MR-3500 Series Compatible Devices 77
9.1 MR-3500 Series ULI Listed Compatible Devices ........................................................... 77
9.2 MR-3500 Compatible Horn/Strobes ............................................................................... 81
9.3 MR-3500 Series ULC Listed Compatible Devices ......................................................... 82
10.0 Appendix C - Manual Panel Configuration 85
10.1 COMMAND MENU ......................................................................................................... 85
10.2 COMMAND MENU/ 1. CONFIGURATION MENU ......................................................... 85
10.3 CONFIGURATION MENU/1. PANEL CONFIGURATION ............................................. 85
10.4 PANEL CONFIGURATION/1. FEATURES .................................................................... 85
10.5 PANEL CONFIGURATION/2. ADDRESS CFG. ............................................................ 89
10.6 PANEL CONFIGURATION/3. DEVICE LABEL .............................................................. 89
10.7 PANEL CONFIGURATION/4. USER MESSAGE .......................................................... 89
10.8 PANEL CONFIGURATION/5. LANGUAGE ................................................................... 89
11.0 Appendix D - Reporting 90
11.1 Ademco Contact-ID MR-3500 Series Event Codes ...................................................... 90
11.2 Security Industries Association SIA Format Protocol MR-3500 Series Event Codes .... 91
12.0 Appendix E - Specifications And Features 92
12.1 MR-3500 Fire Alarm Control Panel ................................................................................ 92
12.2 MR-3500 System Module and Annunciator Specifications ............................................ 93
13.0 Appendix F - Battery Calculations 94
14.0 Warranty and Warning Information 96

3
List of Figures
Figure 1 MR-3500 with DOX-1024DSR ....................................................................................... 9
Figure 2 BBX-1024DS and BBX-1024DSR Installation Instructions and Dimensions ................. 18
Figure 3 Main Board with all Adder Modules Installed ................................................................. 20
Figure 4 Port and Jumper Locations on Main Board .................................................................... 21
Figure 5 Installing the PR-300 Polarity Reversal and City Tie Module ........................................ 23
Figure 6 Installing the ALC-636 Dual Loop Adder ........................................................................ 24
Figure 7 MR-3500 Configurator Date and Time Settings ............................................................. 27
Figure 8 Enabling the Positive Alarm Sequence .......................................................................... 39
Figure 9 Operation Menu ............................................................................................................ 42
Figure 10 LED Indicators and Control Buttons ............................................................................... 55
Figure 11 Numeric Keypad ............................................................................................................ 56
Figure 12 Wire Routing .................................................................................................................. 63
Figure 13 Addressable Loop Wiring - Class B or Style 4 ............................................................... 64
Figure 14 Addressable Loop Wiring - Class A or Style 6 ............................................................... 64
Figure 15 Addressable Loop Wiring - Class X or Style 7 ............................................................... 65
Figure 16 NAC Circuit – Class B or Style Y Wiring ........................................................................ 66
Figure 17 NAC Circuit – Class A or Style Z Wiring ........................................................................ 66
Figure 18 RTI-1 Common Remote Trouble Indicator Wiring .......................................................... 67
Figure 19 Wiring the Dialer ........................................................................................................... 68
Figure 20 Connecting an FACP to a 3G4010 Interface Device in Canada .................................... 69
Figure 21 Connecting an FACP to a 3G4010CF Interface Device outside Canada ...................... 70
Figure 22 Wiring the PR-300 Polarity Reversal and City Tie Module ............................................ 71
Figure 23 Main Power Supply Wiring and Connections ................................................................. 73
Figure 24 Supervision of Auxiliary Supplies ................................................................................... 74

4
List of Tables
Table 1 MR-3500 System Components ...................................................................................... 10
Table 2 Advanced Protocol Detectors ......................................................................................... 15
Table 3 Advanced Protocol Intelligent Modules .......................................................................... 15
Table 4 Advanced Protocol Manual Stations .............................................................................. 16
Table 5 Ancillary Modules ........................................................................................................... 16
Table 6 Bases ............................................................................................................................. 16
Table 7 CLIP Detectors ............................................................................................................... 17
Table 8 CLIP Modules ................................................................................................................. 17
Table 9 Main Board Connectors and Jumper ............................................................................. 22
Table 10 PR-300 Polarity Reversal and City Tie Module Connectors and Jumpers ..................... 23
Table 11 ALC-636 Dual Loop Adder Connectors and Jumpers .................................................... 24
Table 12 UL864 90.23 Table ......................................................................................................... 26
Table 13 Configurable Input Types ............................................................................................... 28
Table 14 Configurable Output Types ............................................................................................ 33
Table 15 Annunciator Address DIP Switch Settings ..................................................................... 40
Table 16 List Bypass Special Characters ..................................................................................... 51
Table 17 Keypad and Cursor button descriptions ......................................................................... 56
Table 18 LED Indicators and Control Buttons ............................................................................... 57
Table 19 Advanced Protocol and CLIP Devices Addressable Loop Wiring Table ........................ 61
Table 20 NAC and Auxiliary Power Circuits Wiring Table ............................................................. 62
Table 21 MRI-502MAP Conventional Zone Module Input Circuit Wiring Table ............................ 62
Table 22 Power Supply Electrical Ratings .................................................................................... 72
Table 23 Compatible DACR Receivers ......................................................................................... 76
Table 24 ULI Advanced Protocol Detectors .................................................................................. 77
Table 25 ULI Advanced Protocol Intelligent Modules ................................................................... 77
Table 26 ULI Advanced Protocol Manual Stations ........................................................................ 77
Table 27 ULI Ancillary Modules .................................................................................................... 77
Table 28 ULI Bases ....................................................................................................................... 78
Table 29 ULI Intelligent Detectors ................................................................................................. 78
Table 30 ULI Intelligent Modules ................................................................................................... 78
Table 31 ULI Two-Wire Smoke Detectors ..................................................................................... 79
Table 32 MR-3500 Compatible Horn/Strobes ............................................................................... 81
Table 33 ULC Advanced Protocol Detectors ................................................................................ 82
Table 34 ULC Advanced Protocol Intelligent Modules .................................................................. 82
Table 35 ULC Advanced Protocol Manual Stations ...................................................................... 82
Table 36 ULC Ancillary Modules ................................................................................................... 82
Table 37 ULC Bases ..................................................................................................................... 83
Table 38 ULC Intelligent Detectors ............................................................................................... 83
Table 39 ULC Intelligent Modules ................................................................................................. 83
Table 40 ULC Two-Wire Smoke Detectors ................................................................................... 84
Table 41 Contact-ID Event Codes ................................................................................................90
Table 42 SIA-DCS Event Codes ...................................................................................................91
Table 43 MR-3500 Specifications ................................................................................................. 92
Table 44 MR-3500 System Modules and Annunciator Specifications .......................................... 93
Table 45 Recommended Batteries ................................................................................................ 95

5
1.0 Industry Canada and FCC Notice
1.1 Notice for all MR-3500 Series Built-In UDACTs Sold in Canada
Secutron's MR-3500 SERIES BUILT-IN UDACT Communicator described in this manual is
listed by Underwriters Laboratories Canada (ULC) for use in slave application under Standard
ULC-S527 (Standard for Control Units for Fire Alarm Systems) and ULC-S559 (Equipment for
Fire Signal Receiving Centres and Systems). These Communicators should be installed in
accordance with this manual; the Canadian / Provincial / Local Electrical Code; and/or the
local Authority Having Jurisdiction (AHJ).
1.2 Industry Canada Notice
Repairs to certified equipment should be made by an authorized Canadian maintenance
facility designated by the supplier. Any repairs or alteration made by the user to this
equipment, or equipment malfunctions, may give the telecommunications company cause to
request the user to disconnect the equipment. Users should ensure for their own protection
that the Earth Ground connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This is necessary both for proper
operation and for protection.
1.3 Notice for all MR-3500 Series Built-in UDACTs Sold in the
U.S.A.
Secutron's MR-3500 SERIES BUILT-IN UDACT Digital Communicator described in this
manual is listed by Underwriters Laboratories Inc. (ULI) for use in slave application in
conjunction with a Listed Fire Alarm Control Panel under Standard 864 (Control Units for Fire
Protective Signalling Systems). These Communicators comply with the National Fire
Protection Association (NFPA) performance requirements for UDACTs and should be installed
in accordance with NFPA 72 Chapter 4 (Supervising Station Fire Alarm System). These
Communicators should be installed in accordance with this manual; the National Electrical
Code (NFPA 70); and/or the local Authority Having Jurisdiction (AHJ).
Attention: Users should not attempt to make such connections themselves, but
should contact the appropriate electric inspection authority, or
electrician, as appropriate.
Notes: The Ringer Equivalence Number (REN) assigned to each terminal device
provides an indication of the maximum number of terminals allowed to be
connected to a telephone interface. The termination on an interface may consist
of any combination of devices subject only to the requirement that the sum of the
Ringer Equivalence Numbers of all the devices does not exceed 5.
The Label Identification Number for this product is US:6OTAL01BMR3500. The
01B represents the REN without a decimal point (for example, 01B is a REN of
0.1B).
!
i

6
Industry Canada and FCC Notice
1.4 FCC Notice
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the telco transformer of this equipment is a label that contains, among other
information, a product identifier in the format US:6OTAL01BMR3500. If requested, this
number must be provided to the telephone company. This equipment is capable of seizing the
line. This capability is provided in the hardware.
Type of Service
The Communicator is designed to be used on standard device telephone lines. It connects to
the telephone line by means of a standard jack called the USOC RJ-11C (or USOC FJ45S).
Connection to telephone company provided coin service (central office implemented systems)
is prohibited. Connection to party lines service is subject to state tariffs.
Telephone Company Procedures
The goal of the telephone company is to provide you with the best service it can. In order to do
this, it may occasionally be necessary for them to make changes in their equipment,
operations or procedures. If these changes might affect your service or the operation of your
equipment, the telephone company will give you notice, in writing, to allow you to make any
changes necessary to maintain uninterrupted service. In certain circumstances, it may be
necessary for the telephone company to request information from you concerning the
equipment which you have connected to your telephone line. Upon request of the telephone
company, provide the FCC registration number and the ringer equivalence number (REN);
both of these items are listed on the equipment label. The sum of all of the REN’s on your
telephone lines should be less than five in order to assure proper service from the telephone
company. In some cases, a sum of five may not be usable on a given line.
If Problems Arise
If any of your telephone equipment is not operating properly, you should immediately remove it
from your telephone line, as it may cause harm to the telephone network. If the telephone
company notes a problem, they may temporarily discontinue service. When practical, they will
notify you in advance of this disconnection. If advance notice is not feasible, you will be
notified as soon as possible. When you are notified, you will be given the opportunity to correct
the problem and informed of your right to file a complaint with the FCC. Contact your
telephone company if you have any questions about your phone line. In the event repairs are
ever needed on the Communicator, they should be performed by Secutron, Inc. or an
authorized representative of Secutron, Inc. For information contact Secutron, Inc. at the
address and phone numbers shown on the back page of this document.

7
2.0 Introduction
This document provides information for the successful installation and operation of the
MR-3500.
2.1 The MR-3500 Addressable Fire Alarm Control Panel
Secutron’s MR-3500 Addressable Fire Alarm Control Panel provides the following:
• Advanced Protocol mode with one or three loops with 159 addressable sensors and 159
addressable modules per loop.
• CLIP Device compatible.
• Four Power Limited Class B (Style Y), Class A (Style Z) NAC circuits.
• NAC circuits may be configured as silenceable signal, non-silenceable signal,
silenceable strobes, non-silenceable strobes, or relay output. The audible signal may be
Steady, Temporal Code, California Code, or March Time.
• Supports sync strobe protocols from major manufacturers.
• Software configuration.
• Two-stage, alarm verification, waterflow retard and positive alarm sequence operations.
• Configurable Signal Silence Inhibit, Auto Signal Silence, Two-Stage Operation, and
One-Man Walk Test.
• Subsequent Alarm, Supervisory, Monitor and Trouble operation.
• Relay Contacts for Common Alarm, Common Supervisory and Common Trouble all
non-disconnectable and Auxiliary Alarm Relay (disconnectable).
• Built-in Dialer Module.
2.1.1 Optional Items
• Supports up to 2 RAX-1048TZDS Display Adder Modules.
• Semi-flush or surface mountable enclosures for retrofits and new installations.
Note: Installation of the MR-3500 Fire Alarm Control panel should be in accordance
with Canadian Electrical Code Part 1, ULC-S524 installation of Fire Alarm
System; or National Electrical Code NFPA 70 and NFPA 72. Final acceptance
subject to the Local Authority Having Jurisdiction (AHJ).
!

8
Introduction
2.2 General Notes
Circuits
Refers to a physical electrical interface for the analog loop, indicating signals or relays, and
common alarm, supervisory, and trouble relay outputs.
Zone/Group
Is a logical concept for a Fire Alarm Protected Area, and will consist of at least one Circuit. The
MR-3500 uses Groups extensively to facilitate annunciation of multiple input and output points
on the 30 (up to 64) LED display and to facilitate the bypassing of inputs and outputs.
Display Points
The MR-3500 LCD display annunciates the status of the system and connected devices.
There are up to two (2) RAX-1048TZDS Display Adder Module Display points that may be
configured to assign LEDs to groups of inputs or outputs. There are two LEDs for every display
point; one single color (yellow) and one dual color (red/yellow).
Wiring Styles
The analog loop can be connected in Class B (Style 4), Class A (Style 6), or Class X (Style 7)
configurations.

9
3.0 MR-3500 Overview
This chapter lists all the possible components of an MR-3500 system.
3.1 MR-3500 Fire Alarm Control Panel Models
All MR-3500 Fire Alarm Control Panels have the following features:
• Main Board, Power Supply and Backbox.
• Multi-zone fire alarm control panel
• MAM-3500 Main Display with 4 x 20 LCD display.
• Class A (Style 6), Class X (Style 7), or Class B (Style 4) analog loop(s).
• Four Power Limited Class B (Style Y), Class A (Style Z) NAC circuits (max 1.5 Amps
each - 6.0 Amps total).
• Dedicated common alarm, supervisory, trouble, and auxiliary alarm relays.
• Additional RAX-1048TZDS Display Adder Module can be added to provide 96
annunciation points per Adder.
• Additional outputs include connections for a RTI remote trouble indicator, PR-300
Reverse Polarity Module, an RS-485 bus for connection of up to seven RAX-LCD-LITE,
RAM-3500-LCDs, SRM-312s and RA-1000 Series annunciators.
• Auxiliary power is available in the form of 24V FWR unfiltered and unsupervised, 24VDC
filtered and regulated, and resettable auxiliary power supply.
Figure 1 MR-3500 with DOX-1024DSR

10
MR-3500 Overview
3.2 MR-3500 System Components
The following table describes the components of the MR-3500.
Table 1 MR-3500 System Components
Model Description
MAM-3500 Main Display
DOX-1024DS White enclosure door
DOX-1024DSR Red enclosure door
ALC-636 636 Point Dual Loop Adder.
RAM-3500-LCD Remote Annunciator with 4-line LCD Display.
PR-300 Polarity Reversal and City Tie Module.
Visual
IndicatorTest

11
MR-3500 Overview
PCS-100 Power Supply Interface Board use for powering
GS3060 Universal Wireless Alarm Communicator.
SRM-312W Smart Relay Module with White Enclosure.
Can support up to 12 relays.
MR-2312-SR12 Smart Relay Module with Red Enclosure.
Can support up to 12 relays.
RAM-1016TZDS 16 Point Annunciator Chassis with 16 Trouble
LEDs.
RAM-1032TZDS 32 point Remote Annunciator with 32 Trouble LEDs.
RAX-1048TZDS 48 Point adder annunciator display with 48 Trouble
LEDs.
Table 1 MR-3500 System Components (Continued)
Model Description

12
MR-3500 Overview
MGD-32 Graphic Annunciator.
RAX-LCD-LITE Remote Annunciator with 4-line LCD Display.
AGD-048 Graphic Annunciator Adder Driver Board.
RTI-1 Common Remote Trouble Indicator, Buzzer and
LED.
MMX-BB-1001 White Enclosure for one annunciator.
MMX-BB-1001R Red Enclosure for one annunciator.
MMX-BB-1002 Enclosure for two annunciators.
Table 1 MR-3500 System Components (Continued)
Model Description
P1
P2
JW5
JW15
JW
2 3 4 9 10 11
JW
8 7 6 14 13 12
JW1
P3
P4
P1
P2
JW5
JW15
JW
2 3 4 9 10 11
JW
8 7 6 14 13 12
JW1
P3
P4

13
MR-3500 Overview
MMX-BB-1002R Red Enclosure for two annunciators.
MMX-BB-1003 White Enclosure for three annunciators.
MMX-BB-1003R Red Enclosure for three annunciators.
MMX-BB-1008 Enclosure for eight annunciators.
MMX-BB-1008R Red Enclosure for eight annunciators.
MMX-BB-1012 Enclosure for twelve annunciators.
Table 1 MR-3500 System Components (Continued)
Model Description

14
MR-3500 Overview
MMX-BB-1012R Red Enclosure for twelve annunciators.
MP-300 End of line resistor plate. 3K9.
MMX-BC-160R External Battery Cabinet.
INX-10A Intelligent NAC Expander Panel.
Table 1 MR-3500 System Components (Continued)
Model Description

15
MR-3500 Overview
3.2.1 Devices
The following tables lists all the devices available for the MR-3500.
Table 2 Advanced Protocol Detectors
Advanced Protocol Detectors
MRI-1251AP Advanced Protocol Ion Smoke Detector
MRI-1251APA Advanced Protocol Ion Smoke Detector ULC
MRI-2251AP Advanced Protocol Photo Smoke Detector
MRI-2251APA Advanced Protocol Photo Smoke Detector ULC
MRI-2251TAP Advanced Protocol Photo Heat Detector
MRI-2251TAPA Advanced Protocol Photo Heat Detector ULC
MRI-2251TMAP Advanced Protocol Acclimate Detector
MRI-2251TMAPA Advanced Protocol Acclimate Detector ULC
MRI-5251AP Advanced Protocol Heat Detector
MRI-5251APA Advanced Protocol Heat Detector ULC
MRI-5251HAP Advanced Protocol High Temperature Heat Detector
MRI-5251HAPA Advanced Protocol High Temperature Heat Detector ULC
MRI-5251RAP Advanced Protocol Rate of Rise Heat Detector
MRI-5251RAPA Advanced Protocol Rate of Rise Heat Detector ULC
Table 3 Advanced Protocol Intelligent Modules
Advanced Protocol Intelligent Modules
MRI-M500MAP Advanced Protocol Monitor Module
MRI-M500MAPA Advanced Protocol Monitor Module ULC
MRI-M500RAP Advanced Protocol Relay Control Module
MRI-M500RAPA Advanced Protocol Relay Control Module ULC
MRI-M500SAP Advanced Protocol Supervised Control Module
MRI-M500SAPA Advanced Protocol Supervised Control Module ULC
MRI-M501MAP Advanced Protocol Mini Monitor Module
MRI-M501MAPA Advanced Protocol Mini Monitor Module ULC
MRI-M502MAP Advanced Protocol Conventional Zone Module
MRI-M502MAPA Advanced Protocol Conventional Zone Module ULC

16
MR-3500 Overview
Table 4 Advanced Protocol Manual Stations
Advanced Protocol Manual Stations
MS-401AP Addressable Single Stage Manual Station ULC
MS-401APU Addressable Single Stage Manual Station UL
MS-402AP Addressable Two Stage Manual Station ULC
Table 5 Ancillary Modules
Ancillary Modules
CR-6 Six Relay Control Module
CZ-6 Six Conventional Zone Interface Module
IM-10 Ten Input Monitor Module
MIX-M500X Fault Isolator Module
MIX-M500XA Fault Isolator Module ULC
SC-6 Six Supervised Control Module
Table 6 Bases
Bases
B210LP Intelligent Flanged Mounting Base
B210LPA Intelligent Flanged Mounting Base ULC
B224BI Intelligent Isolator Base
B224BIA Intelligent Isolator Base ULC
B224RB Intelligent Relay Base
B224RBA Intelligent Relay Base ULC
B501 Intelligent Flangeless Mounting Base
B501A Intelligent Flangeless Mounting Base ULC
DNR Intelligent non-relay photoelectric low-flow duct smoke detector housing
DNRW Watertight Intelligent Non-relay Photoelectric Low-flow Duct Smoke Detector
Housing
DNRA Intelligent Non-relay Photoelectric Low-flow Duct Smoke Detector Housing ULC

17
MR-3500 Overview
Table 7 CLIP Detectors
Intelligent Detectors
MRI-1251B Intelligent Low Profile Ionization Smoke Sensor
MRI-1251BA Intelligent Low Profile Ionization Smoke Sensor ULC
MRI-2251B Intelligent Low Profile Photoelectronic Smoke Sensor
MRI-2251BA Intelligent Low Profile Photoelectronic Smoke Sensor ULC
MRI-2251TB Intelligent Low Profile Photoelectronic Smoke Sensor c/w 135°F Fixed Temp.
Thermal Sensor
MRI-2251TBA Intelligent Low Profile Photoelectronic Smoke Sensor c/w 135°F Fixed Temp.
Thermal Sensor ULC
MRI-2251TMB Intelligent Low Profile Multi-Criteria Sensor
MRI-2251TMBA Intelligent Low Profile Multi-Criteria Sensor ULC
MRI-5251B Intelligent Low Profile Fixed Temp. Thermal Sensor 135°F
MRI-5251BA Intelligent Low Profile Fixed Temp. Thermal Sensor 135°F ULC
MRI-5251H Intelligent Low Profile High Temperature Thermal Sensor 190°F
MRI-5251HA Intelligent Low Profile High Temperature Thermal Sensor 190°F ULC
MRI-5251RB Intelligent Low Profile Fixed Temp. and Rate of Rise Thermal Sensor 135°F
MRI-5251RBA Intelligent Low Profile Fixed Temp. and Rate of Rise Thermal Sensor 135°F ULC
MRI-7251B Intelligent Low Profile Laser Smoke Detector
MRI-7251BA Intelligent Low Profile Laser Smoke Detector ULC
Table 8 CLIP Modules
Intelligent Modules
MRI-500DM Intelligent Dual Monitor Module
MRI-500DMA Intelligent Dual Monitor Module ULC
MRI-M500M Intelligent Addressable Monitor Module
MRI-M500MA Intelligent Addressable Monitor Module ULC
MRI-M500R Intelligent Addressable Relay Module
MRI-M500RA Intelligent Addressable Relay Module ULC
MRI-M500S Intelligent Addressable Supervised Control Module
MRI-M500SA Intelligent Addressable Supervised Control Module ULC
MRI-M501M Intelligent Addressable Mini-Monitor Module
MRI-M501MA Intelligent Addressable Mini-Monitor Module ULC
MRI-M502M Intelligent Addressable Interface Module
MRI-M502MA Intelligent Addressable Interface Module ULC

18
4.0 Installation
This chapter describes the installation of the MR-3500.
4.1 BBX-1024DS and BBX-1024DSR Mechanical Installation
The BBX-1024DS and BBX-1024DSR are suitable for flush or surface mounting, and have a
built-in trim ring.
Figure 2 BBX-1024DS and BBX-1024DSR Installation Instructions and Dimensions
Dimensions of Enclosure (minus built in trim ring) 14.5” x 4.2” x 26”
Distance between horizontal mounting screws 12”
Distance between vertical mounting screws 23.5”
Complete Dimensions of Enclosures 16.3” x 5.5” x 27.5”
26.0 "
14.5 "
4.2 "
External Dimensions
12.0 "
23.5 "
Mounting Dimensions
1.3 " 1.7 "
2.0 "
Top View
2.1 "
1.3 " 6.0 "
9.5 "
Side View